Bundle: Principles Of Foundation Engineering, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
9th Edition
ISBN: 9781337947060
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
Solutions are available for other sections.
Concept explainers
Question
Chapter 12, Problem
To determine
Find the ultimate side skin resistance.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
b) A pre-cast concrete pile of size 310 mm x 310 mm and 16 m length is to be drilled in
a stiff clay deposit. The undrained cohesion of the soil along the embedment of the
pile is shown in Table 1. Determine the allowable load on the pile using the factor of
safety as 2.0. Assume the adhesion factor along the pile is 0.4.
The average values of the undrained shear strength (cu) with depth are given below. If a CFA pile having a diameter of 0.6 m and length of 10 m is to be constructed in this clayey soil, estimate the ultimate side skin resistance Qs.
A group pile has a section of 4 x 4 with each having a diameter of 305 mm are
embedded in clay. The length of the piles are 12 m and the spacing between the piles
(d) are 1.0 m. The recorded soil profile for the ground is shown in Table 1. Propose the
allowable load bearing capacity of the pile with a factor of safety of (FS) of 3.
(b)
TABLE 1: Soil type and soil parameter
Depth
Soil parameter
Unit weight = 17.5 kN/m³
= 20 kN/m2
0.0 m to 2.0 m
Cohesion
%3D
2.0 m to 8.0 m
Unit weight = 18.5 kN/m³
%3D
Cohesion
= 60 kN/m?
8.0 m to 15.0 m Unit weight= 20.1 kN/m³
%3D
Cohesion
= 80 kN/m2
Chapter 12 Solutions
Bundle: Principles Of Foundation Engineering, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
Ch. 12 - Prob. 12.1PCh. 12 - A 20 m long concrete pile is shown in Figure...Ch. 12 - A 500 mm diameter are 20 m long concrete pile is...Ch. 12 - Redo Problem 12.3 using Coyle and Castellos...Ch. 12 - A 400 mm 400 mm square precast concrete pile of...Ch. 12 - Determine the maximum load that can be allowed on...Ch. 12 - A driven closed-ended pile, circular in cross...Ch. 12 - Consider a 500 mm diameter pile having a length of...Ch. 12 - Determine the maximum load that can be allowed on...Ch. 12 - Prob. 12.10P
Ch. 12 - Prob. 12.11PCh. 12 - Prob. 12.12PCh. 12 - A concrete pile 16 in. 16 in. in cross section is...Ch. 12 - Prob. 12.14PCh. 12 - Solve Problem 12.13 using Eqs. (12.59) and...Ch. 12 - Prob. 12.16PCh. 12 - Prob. 12.17PCh. 12 - A steel pile (H-section; HP 310 125; see Table...Ch. 12 - Prob. 12.19PCh. 12 - A 600 mm diameter and 25 m long driven concrete...Ch. 12 - Redo Problem 12.20 using Vesics method, assuming...Ch. 12 - Prob. 12.22PCh. 12 - Prob. 12.23PCh. 12 - Solve Problem 12.23 using the method of Broms....Ch. 12 - Prob. 12.25PCh. 12 - Solve Problem 12.25 using the modified EN formula....Ch. 12 - Solve Problem 12.25 using the modified Danish...Ch. 12 - Prob. 12.28PCh. 12 - Prob. 12.29PCh. 12 - Figure 12.49a shows a pile. Let L = 15 m, D (pile...Ch. 12 - Redo Problem 12.30 assuming that the water table...Ch. 12 - Refer to Figure 12.49b. Let L = 18 m, fill = 17...Ch. 12 - Estimate the group efficiency of a 4 6 pile...Ch. 12 - The plan of a group pile is shown in Figure...Ch. 12 - Prob. 12.35PCh. 12 - Figure P12.36 shows a 3 5 pile group consisting...Ch. 12 - Prob. 12.37P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. f N/mm2 Cross sectionarrow_forwardA frictional pile with a circular cross-section (diameter = D) is pushed into the soil %3D to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. P xx f N/mm2arrow_forwardConsider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?arrow_forward
- Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.arrow_forwardDetermine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure 18.36, with a safety factor of 3. Use the a method for computing the shaft friction. FIG. 18.36arrow_forwardDetermine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load.arrow_forward
- A frictional pile with a circular cross-section (diameter = D) is pushed into the soil to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. P L Cross sectionarrow_forwardSteel pipe piles are to be used as friction piles (i.e., pile capacity is from shaft resistance only) in an area where a deep deposit of normally consolidated clay exists. The soil unit weight is 17kN/m3, with shear strength cohesion cu equal to 45 kPa. Using the total stress α-method, determine the design axial capacity due to shaft resistance for a pile diameter of 0.30 m and an embedded length of 10 m. Apply a factor of safety of 2.75.arrow_forwardA concrete pile of size 50 cm x 50 cm is to be provided in a clay stratum whose unconfined compressive strength is 110 kPa. Compute the minimum length of pile required to carry safe working load of 450 kN with a factor of safety 2.5. Assume adhesion factor as 0.6.arrow_forward
- Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, ơ'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225KN/m? At 12m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 300KN/m? 7m 5m Clay 3 10m Unit weight = 18KN/m Friction angle = 0 degree 2 Cohesion = 100KN/m Figure 1: Pile systemarrow_forwardCheck the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C, = 0.09, ơ'o = 150KN/m? At 10m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 225KN/m? At 12m, e, = 0.55, Cc = 0.32, C, = 0.09, oo = 300KN/m? 7m 5m Clay 10m Unit weight = 18kN/m Friction angle = 0 degree Cohesion = 100KN/marrow_forwardCheck the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning