EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM
5th Edition
ISBN: 8220102803503
Author: Petruzella
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 21RQ
Program Plan Intro
FIFO:
- FIFO is the abbreviation for First In First Out.
- Here, the first word entered will be the first word coming out.
- FIFO arrangement is the best way for
programming queue operations. - FIFO principle is normally used in inventory control systems and data acquisition.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Draw the circuit for parallel in serial out shift registers.
The function of the segment register in protected mode operation is discussed.
Show the steps involved in the followingMOV BX,91CFH ;BX = 91CFHMOV CL,3SHR BX,CL ;shift right BX three times
Show the contents of the flag register.
Chapter 12 Solutions
EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM
Knowledge Booster
Similar questions
- What is the code for AX/AL register?arrow_forwardWhat is the polynomial representation of this linear feedback shift register? I think its 1 + X2 + X3. is that right? should it be the other way around?arrow_forwardDesign a three-bit up/down counter using T flip-flops. It should include a control input called Up/Down. If Up/Down = 0, then the circuit should behave as an up-counter. If Up/Down = 1, then the circuit should behave as a down-counter.arrow_forward
- Design a 2-bit Universal Shift Register. S1 and S0 are the select inputs of MUX. O ie si SO Operation Shift Left 1 Shift Right 1 Parallel Loadarrow_forwardWhat is the code for BP/CH register?arrow_forward2. Using a multiplexer, design a circuit which its output is one if the majority of its input is one; otherwise, its output should be a zero. NOTE: You should use a block diagrams for the multiplexer, but clearly show the input and output lines.arrow_forward
- Write vhdl code for 4-bit Universal shift register using d flip flop with following control mode : Parallel write 00 Shift left 01 Shift right Parallel read 11 10 Write the code using boolean expressionarrow_forwardShift registers are basically storage devices in which data can be shifted in our out in several ways. Select the correct response O True Falsearrow_forwardIf a register has serial inputs and parallel outputs, how can it be utilized to do the opposite function?arrow_forward
- Q1 a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) Part DigClock Part List: OFFTIME = .5uS DSTM1 ONTIME = .5us DELAY = STARTVAL = 0 OPPVAL = 1 DisClock FileStm1 FieStm16 CLK FileStim2 FileStim32 FileStim4 FileStime Libraries Design Cache EVAL 1. SOURCEarrow_forwardDescribe the clock generator in simple terms.arrow_forwardHow to design FSM for a 3-bit shift register and simulate it using programming C?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning