Physics for Scientists & Engineers, Volume 2 (Chapters 21-35)
5th Edition
ISBN: 9780134378046
Author: GIANCOLI, Douglas
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
5. (A). A simple turnbuckle arrangement is constructed from a 40 mm outside diameter
tube threaded internally at each end to take two rods of 25 mm outside diameter with
threaded ends. What will be the nominal stresses set up in the tube and the rods,
ignoring thread depth, when the turnbuckle cames an axial load of 30 kN? Assuming
a sufficient strength of thread, what maximum load can be transmitted by the
turnbuckle if the maximum stress is limited to 180 MN/m?
[39.2, 61.1 MN/m2, 88.4 kN]
6. (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC
is of 20 mm diameter and40 mm long and CD is of 12 mm diameter and 50 mm long.
Determine the stress set up in each section of the bar when it is subjected to an axial
tensile load of 20 kN. What will be the total extension of the bar under this load? For
the bar material, E = 210GN/m?.
[32.63.7, 176.8 MN/m²_ 0.062mm]
(II) An iron bolt is used to connect two iron plates together. The bolt must withstand shear forces up to about 3300 N. Calculate the minimum diameter for the bolt, based on a safety factor of 7.0.
Assume Young’s modulus for bone is 1.40×1010 N/m2
. The bone breaks if stress greater
than 1.50 × 109 N/m2
is imposed on it.
(i) What is the maximum force that can be exerted on the femur bone in the leg if it
has a minimum effective diameter of 2.50 cm?
(ii) If this much force is applied compressively, by how much does the 20.0 cm long bone
shorten?
Chapter 12 Solutions
Physics for Scientists & Engineers, Volume 2 (Chapters 21-35)
Ch. 12.1 - Prob. 1AECh. 12.2 - We did not need to use the force equation to solve...Ch. 12.2 - CHAPTER-OPENING QUESTIONGuess Now! The diving...Ch. 12.2 - Why is it reasonable to ignore friction along the...Ch. 12.3 - Prob. 1EECh. 12.5 - Two steel wires have the same length and are under...Ch. 12 - Describe several situations in which an object is...Ch. 12 - A bungee jumper momentarily comes to rest at the...Ch. 12 - Prob. 3QCh. 12 - Your doctors scale has arms on which weights slide...
Ch. 12 - A ground retaining wall is shown in Fig. 1240a....Ch. 12 - Can the sum of the torques on an object be zero...Ch. 12 - A ladder, leaning against a wall, makes a 60 angle...Ch. 12 - Prob. 8QCh. 12 - Prob. 9QCh. 12 - Place yourself facing the edge of an open door....Ch. 12 - Prob. 11QCh. 12 - Prob. 12QCh. 12 - Prob. 13QCh. 12 - Which of the configurations of brick, (a) or (b)...Ch. 12 - Is the Youngs modulus for a bungee cord smaller or...Ch. 12 - Examine how a pair of scissors or shears cuts...Ch. 12 - Materials such as ordinary concrete and stone are...Ch. 12 - Prob. 1MCQCh. 12 - Prob. 2MCQCh. 12 - Prob. 3MCQCh. 12 - Prob. 4MCQCh. 12 - Prob. 5MCQCh. 12 - Prob. 6MCQCh. 12 - Prob. 7MCQCh. 12 - Prob. 8MCQCh. 12 - Prob. 9MCQCh. 12 - Prob. 10MCQCh. 12 - Prob. 11MCQCh. 12 - (I) A tower crane (Fig. 1248a) must always be...Ch. 12 - Prob. 2PCh. 12 - Prob. 3PCh. 12 - Prob. 4PCh. 12 - (II) Calculate the forces FA and FB that the...Ch. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8PCh. 12 - Prob. 9PCh. 12 - (II) Find the tension in the two wires supporting...Ch. 12 - Prob. 12PCh. 12 - (II) The force required to pull the cork out of...Ch. 12 - Prob. 14PCh. 12 - (II) Three children are trying to balance on a...Ch. 12 - Prob. 16PCh. 12 - (II) A traffic light hangs from a pole as shown in...Ch. 12 - Prob. 18PCh. 12 - Prob. 19PCh. 12 - Prob. 20PCh. 12 - Prob. 21PCh. 12 - Prob. 22PCh. 12 - Prob. 23PCh. 12 - (III) A door 2.30 m high and 1.30 m wide has a...Ch. 12 - Prob. 25PCh. 12 - Prob. 26PCh. 12 - Prob. 27PCh. 12 - (III) A uniform ladder of mass m and length leans...Ch. 12 - (III) A refrigerator is approximately a uniform...Ch. 12 - (III) A 56.0-kg person stands 2.0 m from the...Ch. 12 - Prob. 31PCh. 12 - Prob. 33PCh. 12 - Prob. 34PCh. 12 - Prob. 35PCh. 12 - Prob. 36PCh. 12 - Prob. 37PCh. 12 - Prob. 38PCh. 12 - Prob. 39PCh. 12 - Prob. 40PCh. 12 - (I) A sign (mass 1700 kg) hangs from the end of a...Ch. 12 - Prob. 42PCh. 12 - (II) How much pressure is needed to compress the...Ch. 12 - (II) At depths of 2000 m in the sea, the pressure...Ch. 12 - Prob. 45PCh. 12 - (I) The femur bone in the human leg has a minimum...Ch. 12 - Prob. 47PCh. 12 - (II) (a) What is the maximum tension possible in a...Ch. 12 - (II) If a compressive force of 3.3 104 N is...Ch. 12 - Prob. 50PCh. 12 - (II) Assume the supports of the uniform cantilever...Ch. 12 - Prob. 52PCh. 12 - Prob. 53PCh. 12 - Prob. 54PCh. 12 - Prob. 55PCh. 12 - (III) The truss shown in Fig. 1272 supports a...Ch. 12 - (II) How high must a pointed arch be if it is to...Ch. 12 - Prob. 60GPCh. 12 - A cube of side l rests on a rough floor. It is...Ch. 12 - Prob. 62GPCh. 12 - When a wood shelf of mass 6.6 kg is fastened...Ch. 12 - Prob. 64GPCh. 12 - Prob. 67GPCh. 12 - The mobile in Fig. 1274 is in equilibrium. Object...Ch. 12 - A 65.0-kg painter is on a uniform 25-kg scaffold...Ch. 12 - Prob. 70GPCh. 12 - Prob. 73GPCh. 12 - Prob. 74GPCh. 12 - Prob. 76GPCh. 12 - Prob. 77GPCh. 12 - Prob. 78GPCh. 12 - Prob. 79GPCh. 12 - Parachutists whose chutes have failed to open have...Ch. 12 - Prob. 81GPCh. 12 - One rod of the square frame shown in Fig. 1295...Ch. 12 - A uniform beam of mass M and length l is mounted...Ch. 12 - Prob. 84GPCh. 12 - A uniform 6.0-m-long ladder of mass 16.0 kg leans...Ch. 12 - In Fig. 1279, consider the right-hand...Ch. 12 - Assume that a single-span suspension bridge such...Ch. 12 - A uniform sphere of weight mg and radius r0 is...Ch. 12 - A uniform ladder of mass m and length leans at an...Ch. 12 - Prob. 90GPCh. 12 - Prob. 91GPCh. 12 - A 23-kg sphere rests between two smooth planes as...Ch. 12 - Prob. 93GPCh. 12 - Prob. 94GPCh. 12 - Prob. 95GP
Knowledge Booster
Similar questions
- The center of gravity of a loaded truck depends on how the truck is packed. If it is 4.0 m high and 2.4 m wide, and its CG is 2.2 m above the ground, how steep a slope can the truck be parked on without tipping over (Fig. 9-81)? - 2.4 m- CG 4.0 m 2.2 m FIGURE 9-81 Problem 62.arrow_forward(25) A biomechanical model of the bones and biceps muscles of a person's arm supporting a mass m=2 kg is shown below. The weight of the forearm is 9 N. If the cross section of the tendon AB is 28 mm' what is the average normal stress in the tendon? 4f 290 mm r OS 150 mm 200 mmarrow_forwardFB (I) Three forces are applied to a tree sapling, as shown in Fig. 9–46, to stabilize it. If FA = 385 N and FB = 475 N, find Fc in magnitude 105° and direction. FA FIGURE 9–46 Éc. Problem 1.arrow_forward
- 8arrow_forwardAn inverted conical bar hangs from the ceiling of a building. De- termine the elongation under the action of its own weight. The bar has a length L, diameter D, and the weight per unit volume is .arrow_forwardA cube of side l rests on a rough floor. It is subjected to a steady horizontal pull F, exerted a distance h above the floor as shown in Fig. 9-79. As Fis increased, the block will either begin to slide, or begin to tip over. Determine the coefficient of static friction us so that (a) the block begins to slide rather than tip; (b) the block begins to tip. [Hint: Where will the normal force on the block act if it tips?] h FIGURE 9–79 Problem 60.arrow_forward
- (II) The subterranean tension ring that exerts the balancing horizontal force on the abutments for the dome in Fig. 9–34 is 36-sided, so each segment makes a 10° angle with the adjacent one (Fig. 9–77). Calculate the tension F that must exist in each segment so that the required force of 4.2 x 105 N can be exerted at each corner (Example 9–13). -F 5° 5° FIGURE 9-77 420,000 N Problem 58. Buttressarrow_forwardCalculate the Young’s modulus in the cantilever depression method. The length is 1m which is suspended with a load of 150gm. The depression is found to be 4cm. The thickness of the beam is 5mm and breadth is 3cm. a) 3.92 × 1010 N/m2 b) 9000 × 1010 N/m2 c) 4000 × 1010 N/m2 d) 1.245 ×1010 N/m2arrow_forwardA farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands more than the glass when it warms up, in such a way that the volume increases by 0.4%. Calculate the force exerted by the juice per square centimeter if its bulk modulus is 1.8 × 109 N/m2, assuming the bottle does not break.arrow_forward
- "One end of a steel rod of radius R = 10mm and length L = 90 cm is held in a vise. A force of magnitude F = 50000 N is then applied perpendicularly to the end face (uniformly across the area) at the other end, pulling directly away from the vise. What will be the elongation of the rod (in the unit meters)? Young modulus is 109 N/m2y" 200 x 7.2 x 10-4 3.4 x 10-4 4.6 x 10-4 2.7 x 10-4arrow_forwardA uniform meter stick supported at the 25-cm mark is in equilibrium when a 1-kg rock is suspended at the 0-cm end (as shown in Fig. 9–37). Is the mass of the meter stick greater than, equal to, or less than the mass of the rock? Explain your reasoning. FIGURE 9-37 Question 8.arrow_forward'A model for the elbow joint models the bicep muscle connecting to the horizontal forearm by a vertical tendon 4cm from the elbow joint. A mass m is held in the hand 30cm from the elbow joint. If the maximum tension that can be exerted by the tendon before injury occurs is 2250N, find the maximum mass that can be held in this way.' Im stuck on this questionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University