SHIGLEY'S MECH.ENGINEERING DESIGN-EBK>I
10th Edition
ISBN: 9781259489563
Author: BUDYNAS
Publisher: INTER MCG
expand_more
expand_more
format_list_bulleted
Textbook Question
thumb_up100%
Chapter 12, Problem 3P
A journal bearing has a journal diameter of 3.000 in, with a unilateral tolerance of −0.001 in. The bushing bore has a diameter of 3.005 in and a unilateral tolerance of 0.004 in. The bushing is 1.5 in long. The journal speed is 600 rev/min and the load is 800 lbf. For both SAE 10 and SAE 40, lubricants, find the minimum film thickness and the maximum film pressure for an operating temperature of 150°F for the minimum clearance assembly.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
15.)A full journal bearing has a journal diameter of 4.000in. with a unilateral tolerance of -0.004in. The bushing bore has a diameter of 4.004in and unilateral tolerance of +0.004in. the bearing is 3in long. The journal load is 3000 lbf and it runs at a speed of 400 rpm. What is the load per projected bearing area 9P) in psi?
Choose answer below
75
100
125
250
16.)For the bearing in problem #15, if the lubricant average viscosity is 9 ureym, what is the Sommerfield number (assuming minimum clearance)
Choose answer below
Between 0.6 and 0.7
Between 0.5 and 0.6
Between 0.3 and 0.4
Between 0.2 and 0.3
A pressure-fed bearing has a journal diameter of 75.00 mm with a unilateral tolerance of -0.05 mm. The bushing bore diameter is 75.084 mm with a unilateral tolerance of 0.010 mm.The length of the bushing is 62.00 mm. Its central annular groove is 12.00 mm wide and is fed by SAE 30 oil is 53 °C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 30 kN. The sump can dissipate 300 watts per bearing if necessary. For minimum radial clearances, find:
the average temperature.
Given the film temperature is 85 o C
A full journal bearing has a journal diameter of 25 mm, with a unilateral tolerance of -0.03 mm. The bushing bore has a diameter of 25.03 mm and a unilateral tolerance of 0.04 mm. The 1/d ratio is 1/2. The load is 1.2 kN and the journal runs at 1100 rev/min. If the average viscos- ity is 55 mPa • s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Chapter 12 Solutions
SHIGLEY'S MECH.ENGINEERING DESIGN-EBK>I
Ch. 12 - A full journal bearing has a journal diameter of...Ch. 12 - A full journal bearing has a journal diameter of...Ch. 12 - A journal bearing has a journal diameter of 3.000...Ch. 12 - Prob. 4PCh. 12 - Prob. 5PCh. 12 - Prob. 6PCh. 12 - Prob. 7PCh. 12 - Prob. 8PCh. 12 - A full journal bearing is 28 mm long. The shaft...Ch. 12 - A 114114 in sleeve bearing supports a load of 700...
Ch. 12 - A full journal bearing has a shaft diameter of...Ch. 12 - Prob. 12PCh. 12 - Prob. 13PCh. 12 - A natural-circulation pillow-block bearing with...Ch. 12 - An eight-cylinder diesel engine has a front main...Ch. 12 - A pressure-fed bearing has a journal diameter of...Ch. 12 - Design a central annular-groove pressure-fed...Ch. 12 - Repeat design problem Prob. 1218 using the nominal...Ch. 12 - Table 12-1 gives the Seireg and Dandage curve fit...Ch. 12 - For Prob. 1218 a satisfactory design is...Ch. 12 - An Oiles SP 500 alloy brass bushing is 0.75 in...Ch. 12 - Prob. 23P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- It has a full-slide type bearing rotating at a speed of 1975 rpm.A load of 5693 N is applied. SAE 40 oil in bearing at 60C inlet temperatureplanned to be used.Shaft and bushing diameters in bearing with tolerance data 41−0.010 respectively+0.000mmand 41.125−0.000+0.100 mm.Average radial clearance mounting for this bearing with bush length 20.50 mmCalculate the following;a) Bearing characteristic number,b) Minimum lubricant film thickness,c) Eccentricity value,d) coefficient of friction,e) Average oil film temperature andf) Find the Tmax temperature value.arrow_forwardA full journal bearing has a nominal diameter of 60.0 mm, a bearing length of 30.0 mm and supports a load of 3200 N when running at the design speed of 3200 rpm. The radial clearance has been specified as 0.04 mm. An SAE 20 oil has been chosen and the lubricant supply system is capable of delivering the lubricant to the bearing at 60oC. Using the Raimondi and Body design charts;1.1 find the temperature rise of the lubricant, (19)1.2 the total flow rate required, (1)1.3 the torque required to overcome friction (3)1.4 and the power dissipated in the bearing.arrow_forwardA natural feed journal bearing of diameter 50mm and length 50mm operating at 20rev/s. Carries a load of 2KN. The lubricant used has a viscosity of 20MPa. The radial clearance is 50um. The Sommerfeld number for the bearing?arrow_forward
- Calculate the basic rating life at 90% reliability for the following cylindrical roller bearing and conditions.Fr 5.05 kNFa 3.12 kNBearing: NU 1010 ECP (on pp 522 in the SKF catalogue)Clearance: Normal Give the answer in millions of revolutions.arrow_forwardThe axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.arrow_forwardA conical Clutch transmits rotation from one rotating shaft to another though frictional forces on the conical face. The following data is for a conical clutchInside Diameter 25.0 mmOutside Diameter 100 mmCoefficient of Friction 0.33Axial Force 1000NIncluded angle 100 degreeRotational speed 1500rev/minuteCalculate the Torque and Power that can be transmitted without slipping using both Uniform Pressure Theory and Uniform Wear Theoryarrow_forward
- Thory of machine: Select one of the following bearing for the load conditions. Radial load, F=3000 N, Axial load, F = 1600 N, RPM = 1000. (1) Deep Groove ball bearing dynamic load rating=47000 N radial bad factor, X=0.56 Axial load factor, Y= 1.83 (i) Cylindrical roller bearing Dynamic load rating 28000 N radial load factor, X=1.0 axial load factor, Y=0.0arrow_forwardWrite briefly about fits and tolerances used in design. And solve this example: A medium force fit on a 50 mm shaft requires a hole tolerance of 0.025 mm and a shaft tolerance of 0.016 mm. The maximum interference is to be 0.042 mm. How will you dimension the hole and the shaft, if hole deviation is H?arrow_forwardA double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to overcome the collar friction? Group of answer choices 630000 N mm 315000 N mm 819000 N mm 409500 N mmarrow_forward
- Problem (2): Determine tolerance value and limit dimension of the rod which a diameter is ∅47 mm (nominal size), according to the e6 limit deviation (∅47e6). es=-25 mkm, ei=-41 mkm. Determine the basic size, tolerance and limit dimensions.arrow_forwardA wet disk clutch is to be designed to transmit 150 Nm of torque at 1200 rpm using 4 pairsof sintered lining with a maximum pressure at 1.8 N/mm² and the coefficient of friction as0.06. Assume uniform wear, compute the following:i.The required inner and outer diameters of the sintered lining if the internal diametershould be 0.577 of the external diameter.ii.The number of disks needed.iii.The power transmitting capacity.iv.The axial force exerted by the springs to keep the clutch engaged.arrow_forwardQ1. A tensile testing machine operates using two lead screws. Both lead screws have a square thread profile and can withstand the maximum load of 16 tonnes & torque of 150 KNm. The pitch width p = l = 4 mm. what is the efficiency of the square thread?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License