Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 7ASRQ
Technician A uses a 30-degree stone for topping a 45-degree valve seat. Technician B uses a 60-degree stone to lower a 45-degree valve seat. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?
Technician A uses a feeler gauge and straightedge to determine the pump cover flatness.Technician B uses an outside micrometer tomeasure the diameter and thickness of theouter rotor. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor B
what can happen when valve spring tension is too low?
Chapter 12 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - Prob. 8RQCh. 12 - To ensure proper seating of the valve, the valve...Ch. 12 - When checking valve fit, contact between the valve...
Ch. 12 - If the valve face and valve seat do not contact...Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - Which of the following statements is not true?...Ch. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - When fitting a freshly ground valve into a freshly...Ch. 12 - Technician A says off-square springs may cause...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - Technician A uses a 30-degree stone for topping a...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says it is not necessary to measure valve stem height unless the valves have been replaced. Technician B says valve stem height can be adjusted with shims. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that positive valve stem seals fit tightly around the top of the valve guide. Technician B says that positive stem seals scrape oil off the valve as it moves up and down. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following is not a type of valve guide seal? Positive Negative Umbrella O-ringarrow_forward
- Technician A uses a feeler gauge and straightedge to determine the pump cover flatness. Technician B uses an outside micrometer to measure the diameter and thickness of the outer rotor. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says an engine may use one or more valve springs per valve. Technician B says additional valve springs are used to control vibration and increase total pressure. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTrue or False: All gas valves snap open and closed.arrow_forward
- Technician A uses soft gaskets on valve covers. Technician B uses soft gaskets on water pumps. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following statements is not true? Normally the desired valve face-to-seat contact area for intake valves is 1 inch. Normally the desired valve face-to-seat contact area for exhaust valves is 1 inch. The average valve seat width is 0.060 inch and the average seat begins 0.030 inch from the valve margin. A properly reconditioned seat has the correct seat width and sealing position on the valve face.arrow_forwardWhich among the valves is called non return valve a.flap check b.ball c.plunger valve d.diaphragm e.Checkarrow_forward
- Valves are favored because of their lower cost and lighter weight Correct answer plug ball poppet butterflyarrow_forwardthe metring valve portion of combination valve fails .technician A says that this means the entire combination valve must be replaced.Technician B says that the metring part can be repaired who is correct?arrow_forwardA cylinder leakage (leak-down) test indicates 30% leakage, and air is heard coming out of the air inlet. Technician A says that this is a normal reading for a slightly worn engine. Technician B says that one or more intake valves are defective.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license