Concept explainers
A uniform beam of mass M and length l is mounted on a hinge at a wall as shown in Fig. 12–91. It is held in a horizontal position by a wire making an angle θ as shown. A mass m is placed on the beam a distance x from the wall, and this distance can be varied. Determine, as a function of x, (a) the tension in the wire and (b) the components of the force exerted by the beam on the hinge.
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Modified Mastering Physics with Pearson eText -- Combo Access -- for Physics for Scientist and Engineers (18 week)
Additional Science Textbook Solutions
College Physics: A Strategic Approach (3rd Edition)
Conceptual Integrated Science
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
Essential University Physics (3rd Edition)
Introduction to Electrodynamics
An Introduction to Thermal Physics
- A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.arrow_forwardA uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.arrow_forwardIn Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?arrow_forward
- 10) One end of a uniform beam is hinged to a wall and the other end is supported by a tension wire that makes angles 0 = 25° with both the wall and the beam as shown in the figure below. The beam is 1 m long and weighs 222 N with its center of mass located at the half of its total length. Find (a) the tensile force in the wire, (b) the horizontal component of the force of the hinge on the beam, and (c) the vertical component of the force of the hinge on the beam. Hingearrow_forwardSir Lost-a-Lot dons his armor and sets out from the castle on his trusty steed (see figure below). Usually, the drawbridge is lowered to a horizontal position so that the end of the bridge rests on the stone ledge. Unfortunately, Lost-a-Lot's squire didn't lower the drawbridge far enough and stopped it at e = 20.0° above the horizontal. The knight and his horse stop when their combined center of mass is d = 1.25 m from the end of the bridge. The uniform bridge is { = 7.25 m long and has mass 2 500 kg. The lift cable is attached to the bridge 5.00 m from the hinge at the castle end and to a point on the castle wall h = 12.0 m above the bridge. Lost-a-Lot's mass combined with his armor and steed is 1 070 kg. While Lost-a-Lot ponders his next move, the enemy attacks! An incoming projectile breaks off the stone ledge so that the end of the drawbridge can be lowered past the wall where it usually rests. In addition, a fragment of the projectile bounces up and cuts the drawbridge cable! The…arrow_forwardA 10 kg ladder has a length of 8 feet and leans on a vertical wall with an angle of 30 degree. Determine the force exerted by the tip of the ladder on the vertical wall and the force exerted by its foot on the horizontal ground. ( complete solution)arrow_forward
- 1. (1) Three forces are applied to a tree sapling, as shown in Fig. 12-45, to stabilize it. If FA = 385 N and FB = 475 N, find Fe in magnitude and direction. FB FIGURE 12-45 FC Problem 1. FIGURE 12-46 Problem 2. 2. (1) Approximately what magnitude force, FM, must the extensor muscle in the upper arm exert on the lower arm to hold a 7.3-kg shot put (Fig. 12-46)? Assume the lower arm has a mass of 2.3 kg and its CG is 12.0 cm from the elbow-joint pivot. 2.5 cm FM -30.0 cm- 105° Elbow joint FAarrow_forwardA metal rod of mass M = 6 kg and length L = 0.5 m, is attached at one end by a hinge to a vertical wall. It is initially supported at the other end so that it is in static equilibrium and lies horizontally. (a) (i) Determine the magnitude and direction of the force on the bar due to the support. (ii) Determine the magnitude and direction of the force on the bar due to the hinge. (b) Show that the moment of inertia of the bar about the end that is attached to the wall is IH = 0.5 kg m2 (c) The support is removed and the bar swings down about the end attached to the hinge. What is the acceleration of a point on the end of the rod just after the support is removed (at this instant the acceleration vector will point directly down)? Give your result in terms of g.arrow_forwardA uniform 30-lb beam, 10 feet long is carried by two mean A and B, one at each end of the beam. a) If A exerts a force of 25 lbs, where must a load of 50 lbs be placed on the beam? b) What force does B exert? ( Complete Solution)arrow_forward
- In the figure, one end of a uniform beam of weight 100 N is hinged to a wall; the other end is supported by a wire that makes angles 8- 29 with both wall and beam. Find (a) the tension in the wire and the (b) horizontal anid (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units Units (b) Number Units (c) Nurmiberarrow_forward(b) A heavy uniform rod AB of weight W is hinged at A to a fixed point. It is pulled aside by a horizontal force P so that it rests inclined at an angle 0 to the vertical. Show that (i) the magnitude of the force Pis 1-cos2e W 2V 1-sin24 (ii) the reaction at the hinge is V3+ sec*0arrow_forward(a) A uniform steel beam of mass 200.00 kg is held up by a steel cable that is connected to the beam a distance L 6.00 m from the wall, at an angle 0=30.00° as shown Figure 1. The beam is bolted to the wall with an unknown force F exerted by the wall on the beam. An object of mass 600.00 kg, resting on top of the beam, is placed a distance d 2.00 m from the wall. Solve this problem fully, by finding the tension in the cable, the horizontal and vertical components of the force that the wall exerts on the beam and its magnitude and its direction. Figure 1arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University