Concept explainers
One rod of the square frame shown in Fig. 12–95 contains a turnbuckle which, when turned, can put the rod under tension or compression. If the turnbuckle puts rod AB under a compressive force F, determine the forces produced in the other rods. Ignore the mass of the rods and assume the diagonal rods cross each other freely at the center without friction. [Hint: Use the symmetry of the situation.]
Want to see the full answer?
Check out a sample textbook solutionChapter 12 Solutions
Modified Mastering Physics with Pearson eText -- Standalone Access Card -- for Physics for Scientists & Engineers with Modern Physics
Additional Science Textbook Solutions
Lecture- Tutorials for Introductory Astronomy
Applied Physics (11th Edition)
University Physics (14th Edition)
Sears And Zemansky's University Physics With Modern Physics
Cosmic Perspective Fundamentals
The Cosmic Perspective (8th Edition)
- Check Your Understanding Solve Example 12.1 by choosing the pivot at the location of the rear axle.arrow_forwardA wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.arrow_forward(24) Assuming the lower arm has a mass of 2.8 kg and its CG is 12 cm from the elbow- joint pivot, how much force must the extensor muscle in the upper arm exert on the lower arm to hold a 7.5 kg shot put (Fig. 12-7)? 11) 2.5 cm F M A) 100 N 30.0 cm- Elbow joint B) 750 N C) 1500 N D) 500 N E) 1000 Narrow_forward
- 'A model for the elbow joint models the bicep muscle connecting to the horizontal forearm by a vertical tendon 4cm from the elbow joint. A mass m is held in the hand 30cm from the elbow joint. If the maximum tension that can be exerted by the tendon before injury occurs is 2250N, find the maximum mass that can be held in this way.' Im stuck on this questionarrow_forward- 5. Two identical, uniform beams of length 3 m and weighing 260 N each are connected at one end by a frictionless hinge. A light horizontal crossbar, attached at the midpoints of the beams maintains an angle 50° between the beams. The beams are suspended from the ceiling by vertical wires so they form a V. See figure. (a) What force does the crossbar exert on each beam? (b) Is the crossbar under compression or tension, i.e. are the ends of the crossbar being pushed together or stretched farther apart? (c) What force (magnitude and direction) does the hinge exert on each beam? Crossbar Hingearrow_forward(III) A door 2.30 m high and 1.30 m wide has a mass of 13.0 kg. A hinge 0.40 m from the top and another hinge 0.40 m from the bottom each support half the door's weight (Fig. 9–69). Assume that the center of gravity is at the geometrical center of the door, and determine 40 cm 2.30 m the horizontal and vertical force components exerted by each hinge on the door. -1.30 m- F40 cm FIGURE 9-69 Problem 29.arrow_forward
- H:21)arrow_forwardA uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 7.5 kg, a length of 2.3 m, is at an angle of 29° above the horizontal, and is held in place by a horizontal cord attached to the other end of the rod and bolted to the wall above the base of the rod. (a) Determine the tension in the cord. 63.715 X Where is a convenient point about which to take the torques? See if you can write an expression for the torque in terms of the force producing the torque and the perpendicular distance from the line of action of the force to the point about which we have specified to determine the torque. See if you can write a second condition of equilibrium that will allow you to determine the tension in the cord. N (b) Determine the horizontal and vertical components of the force exerted on the rod by the hinge. 36.788 X FH = Now that you know the tension in the cord from part (a), see if you can write a first condition of equilibrium statement that will allow you to…arrow_forwardKPECTED HAS OCCU... Subject ystem S- rchpool.sona- ems.com man Subject Pool tem Department... 6³ 2 [108 W 24,919 Xx :8: F2 3 6. A 150 kg uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. Calculate the magnitude of the tension in the wire if the angle between the cable and the horizontal is 8 = 46°. X 1832.64 N E 20 F3 $ 4 R HEATRA MAL 2 7 F4 % 5 T F5 ^ 6 tv ♫ MacBook Air F6 Y & 7 44 F7 U M M | L T E 10 * 8 0 30.0⁰ DII F8 ( 9 Beam A DD F9 O O W F10 zoom B P C F11 ISUIH by mi 04 M vauies or roc puffer d + = F12 deletearrow_forward
- 17-45. The drop gate at the end of the trailer has a mass of 1.25 Mg and mass center at G. If it is supported by the cable AB and hinge at C, determine the tension in the cable when the truck begins to accelerate at 5 m/s?. Also, what are the horizontal and vertical components of reaction at the hinge C? 30 1.5 m 45°arrow_forward(II) A uniform steel beam has a mass of 940 kg. On it is resting half of an identical beam, as shown in Fig. 9-60. What is the vertical support force at each end? •M •Marrow_forwardA metal rod of mass M = 6 kg and length L = 0.5 m, is attached at one end by a hinge to a vertical wall. It is initially supported at the other end so that it is in static equilibrium and lies horizontally. (a) (i) Determine the magnitude and direction of the force on the bar due to the support. (ii) Determine the magnitude and direction of the force on the bar due to the hinge. (b) Show that the moment of inertia of the bar about the end that is attached to the wall is IH = 0.5 kg m2 (c) The support is removed and the bar swings down about the end attached to the hinge. What is the acceleration of a point on the end of the rod just after the support is removed (at this instant the acceleration vector will point directly down)? Give your result in terms of g.arrow_forward
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning