EBK ACTIVITIES MANUAL FOR PROGRAMMABLE
5th Edition
ISBN: 8220102795983
Author: Petruzella
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 13, Problem 1P
Program Plan Intro
Programmable Logic Controller (PLC):
- PLC is a specialized computer used in industrial segments to control machines and process.
- PLC is program that consists of a set of instructions which resembles the controlling functions needed to perform specific tasks.
- The function of PLC is similar to that of a relay and hence, in an industrial segment a relay is greatly replaced by a suitable PLC.
- When compared to general Personal Computer (PC), a PLC is available in small and tiny sizes.
- The basic architecture of a PLC consists of an input-output interface module and a small Central Processing Unit (CPU) that runs by controlling
programming language.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the difference between modes of operation (run,prog,rem)in plc
Describe How a Time-driven sequence PLC program operates.
8-
...... can be connected to the analog
******
input of the PLC.*
O Level switches
Ph
O Flow switches
Pushbutton switches
Selector switches
Chapter 13 Solutions
EBK ACTIVITIES MANUAL FOR PROGRAMMABLE
Ch. 13 - Prob. 1RQCh. 13 - Prob. 2RQCh. 13 - Prob. 3RQCh. 13 - List three potential noise-generating inductive...Ch. 13 - Prob. 5RQCh. 13 - Prob. 6RQCh. 13 - Prob. 7RQCh. 13 - Under what condition can a ground loop circuit be...Ch. 13 - Prob. 9RQCh. 13 - What operating state will cause an inductive load...
Ch. 13 - Prob. 11RQCh. 13 - Prob. 12RQCh. 13 - Prob. 13RQCh. 13 - Prob. 14RQCh. 13 - Prob. 15RQCh. 13 - List four uses for the data monitor function.Ch. 13 - Prob. 17RQCh. 13 - Prob. 18RQCh. 13 - Prob. 19RQCh. 13 - Prob. 20RQCh. 13 - Prob. 21RQCh. 13 - Prob. 22RQCh. 13 - Prob. 23RQCh. 13 - Prob. 24RQCh. 13 - Prob. 25RQCh. 13 - Prob. 26RQCh. 13 - Prob. 27RQCh. 13 - Prob. 28RQCh. 13 - Prob. 29RQCh. 13 - Prob. 30RQCh. 13 - Prob. 1PCh. 13 - A fuse is blown in an output module. Suggest two...Ch. 13 - Prob. 3PCh. 13 - Prob. 4PCh. 13 - Prob. 5PCh. 13 - Prob. 6PCh. 13 - A specific output is forced on, but the LED module...Ch. 13 - An electronic-based input sensor is wired to a...Ch. 13 - Prob. 9PCh. 13 - Prob. 11PCh. 13 - Prob. 12PCh. 13 - Prob. 13PCh. 13 - The program of Figure 13-39 is supposed to execute...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- PLC programming Draw or write a ladder plc diagr for 3 proximity sensor. The proximity sensor is position right and left and 1 in front.arrow_forward.............Control loop is a continuous cycle of the PLC reading Ladder Logic O Outputs Inputs Oarrow_forwardWhat are some good and bad applications of PLCs?arrow_forward
- .....CAPTION PLEASE DRAWarrow_forwardA traffic light PLC program working with a screen will be installed. We will enter and adjust the intervals on the screen. (Red, green and yellow light flashing times). Put the every step's picture please.arrow_forwardThis assignment is a research about SCADA systems and programs used to make SKADA for Schneider PLCarrow_forward
- 1- Write a PLC ladder program to implement the process illustrated in Figure. 2- Indicate all the input and output field devices in their un-actuated conditions with symbolic addresses. The sequence of operation requires that: A start/stop pushbutton station is used to start and When the process starts, the tank is empty and solenoid A energizes to start filling the tank with liquid. As the tank fills, the Empty sensor switch closes. When the tank is half full, the Mid-full level sensor switch closes and the motor starts running to mix the liquid. When the tank is full, the Full level sensor switch closes momentarily so that: stop the process. a- The motor stops. b- Solenoid A is de-energized. c- Solenoid B is energized to empty the tank. When the tank is completely empty, the Empty sensor switch opens to de-energize solenoid B. The start button is pressed to repeat the sequence. out Puts SOL A oulput Motor Infut Full level sensor switch Mid-Full level Empty sensor sensor switch switch…arrow_forward1- Write a PLC ladder program to implement the process illustrated in Figure. 2- Indicate all the input and output field devices in their un-actuated conditions with symbolic addresses.arrow_forwardWhat is the significance of watchdog timers in many embedded systems?arrow_forward
- In PLC operation retrieves the data into an output module Input scan Output scan Program scan None of the abovearrow_forwardThe advantages of PLCs include: a. Reliability, Improved maintenance and troubleshooting and high cost b. Reliability, Improved maintenance and troubleshooting and offline programming c. Reliability, Limited application base, low costarrow_forwardA microcontroller is running at system clock frequency. Timer 2 is configured for a frequency of 125 kHz. The prescalar value of the Timer 2 counter is(a) 64(b) 128(c) 32(d) 256arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning
What is a Thyristor? - A Galco TV Tech Tip; Author: GalcoTV;https://www.youtube.com/watch?v=LBb_Qz7J3zA;License: Standard Youtube License