![Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)](https://www.bartleby.com/isbn_cover_images/9780134009087/9780134009087_largeCoverImage.gif)
Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)
5th Edition
ISBN: 9780134009087
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 13, Problem 3CQ
To determine
Which technician is correct?
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches?
a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds
While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct?
a. A only b. B only c. both A and B d. neither A nor B
Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation.
a. True b. False
Rusted-through brake lines are uncommon.
a. True b. False
A technician is diagnosing a vehicle with…
Which force do not cause rotation
When reviewing the procedure for replacing an axle boot,
Technician A says that the position of the old boot should be marked on the shaft before removing it.
Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
Chapter 13 Solutions
Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What type of lever produces a great amount of force at the expense of speed? Third-class lever Second-class lever First-class lever Fourth-class leverarrow_forwardYou can use a lever to increase force, distance, and speed. true or false just put answerarrow_forwardTrue or False 1. It is acceptable to use a hoist to lift something that weighs more than the rating on the hoist when the load is lifted carefully. 2. Typically, combustible material accidents occur at higher temperatures while flammable material accidents occur at room temperature. 3. Water reactive chemicals include calcium carbide, cyclooctene, metal hydrides, and metals like sodium and potassium. 4. When driving material lifting equipment, workers should maintain at least a 5-foot clearance from overhead power lines. 5. Workers should use at least 2 straps placed equally from the center when lifting a long I-beam. ******************************************************************************************** Multiple Choice 1. Which of the following chemicals is not considered a liver toxin? A. Glacial acetic acid B. Carbon Tetrachloride C. Ethanol D. Trichloroethylene 2. Which of the following is a safety practice intended to protect workers from a lightning strike? A. Use a metal…arrow_forward
- 1.2 Please select all the correct statement blow. A. Retaining rings are inappropriate to retain hubs and bearings onto shafts. B. During shaft design, the locations with the minimum torque and moment should be identified. C. A rivet can always provide a much stronger attachment than a bolt or screw of the same diameter. D. Power screws are used to convert the rotary motion of either the nut or the screw to relatively slow linear motion of the mating member along the screw axis. E. Single-row ball bearings (as shown in the figure below) can carry a significant amount of trust load and can carry more trust load than roller bearings (as shown in the figure below). single-row ball bearing Explanation: roller bearingarrow_forwardWhat additional force A is needed to keep the block in static equiarrow_forwardAnswer only answer 1 to 5 1. As long as the sum of the torques about any axis on a body is zero, it is in complete equilibrium. A.False B.True 2.With the same engine displacement, diesel-powered automobiles typically produce greater torque on the tires than their gasoline-powered counterpart. This means that the diesel variant has greater towing capacity than the gasoline variant. A.True B.False 3. Gravitational potential energy is always positive. A.False B.True 4.Kinetic energy is always positive. A.True B.False 5.A car traveling at constant speed has net work of zero done on it. A.True B.Falsearrow_forward
- Draw FBD of Bicycle axle (Thru axle)arrow_forwardA vehicle to be liftedarrow_forwardWhich of the following choices best represents force? A. A push or pull always causing motion B. A push or pull always causing acceleration C. A push or pull acting without another object D. A push or pull acting on an objectarrow_forward
- The primary manufacturing process for the rocker arm is stamping. True Falsearrow_forwardPlease specify which of the following forces are not conservative forces______. a. Reaction normal force b. Reaction friction force c. Linear Spring Force d. Weightarrow_forwardWhen discussing axle hub nuts, Technician A says that they are never to be reused after they have been staked. Technician B says that they should be chiseled off the stub axle if they are difficult to remove. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781133612315/9781133612315_smallCoverImage.gif)
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Engineering Basics - Statics & Forces in Equilibrium; Author: Solid Solutions - Professional Design Solutions;https://www.youtube.com/watch?v=dQBvQ2hJZFg;License: Standard YouTube License, CC-BY