EP ENGR.MECH.-MOD.MASTERING ACCESS
15th Edition
ISBN: 9780134867267
Author: HIBBELER
Publisher: PEARSON CO
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13, Problem 40P
The 400-lb cylinder at A is hoisted using the motor and the pulley system shown. If the speed of point B on the cable is increased at a constant rate from zero to vB = 10ft/ s in t = 5 s, determine the tension in the cable at B to cause the motion.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The weight of the spring held follower AB is 0.367 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.2 ft and z = (0.1sin20) ft. If the cam is rotating at a constant rate of 6
rad/s, determine the force, in lb, at the end A of the follower where 0 = 45°. In this position, the spring is compressed 0.4 ft. Neglect friction at the bearing C. Round your answer to 3 decimal places.
6 = 6 rad/s
0.2 ftX
z = 0.1 sin 20
Z
A
k = 12 lb/ft
с
B
The constant tensions of 200N and 160 N are ap-
Q2
plied to the hoisting cable as shown. If the velocity
v of the load is 2 m/s down and the angular velocity
w of the pulley is 8 rad/s counterclockwise at time
t = 0, determine v and w after the cable tensions
have been applied for 5 s. Note the independence of
the results.
200 N
160 N
300 mm
15 kg
k = 250 mm
20 kg
The spring-held follower AB has a weight of 0.75 lb and moves
back and forth as its end rolls on the contoured surface of the
cam, where r=0.2 ft and z = (0.1sine) ft. If the cam is rotating at a
constant rate of 6 rad/s, determine the force at the end A of the
follower when e=90°. In this position the spring is compressed
0.4 ft. Neglect friction at the bearing C.
z = 0.1 sin 20
0.2 ft
e = 6 rad/s
k = 12 lb/ft
Fs
FA-
T
Chapter 13 Solutions
EP ENGR.MECH.-MOD.MASTERING ACCESS
Ch. 13 - Prob. 1FPCh. 13 - If motor M exerts a force of F = (10t2 + 100) N on...Ch. 13 - A spring of stiffness k = 500 N/m is mounted...Ch. 13 - Prob. 4FPCh. 13 - Block B rests upon a smooth surface. If the...Ch. 13 - The 6-lb particle is subjected to the action of...Ch. 13 - If blocks A and B of mass 10 kg and 6 kg...Ch. 13 - Determine the time needed to pull the cord at B...Ch. 13 - Prob. 12PCh. 13 - Block A has a weight of 8 lb and block B has a...
Ch. 13 - The 2-Mg truck is traveling at 15 m/s when the...Ch. 13 - The motor lifts the 50-kg crate with an...Ch. 13 - Prob. 18PCh. 13 - Prob. 19PCh. 13 - The 50-kg block A is released from rest. Determine...Ch. 13 - Prob. 28PCh. 13 - Prob. 29PCh. 13 - Prob. 31PCh. 13 - The tractor is used to lift the 150-kg load B with...Ch. 13 - Prob. 35PCh. 13 - Prob. 39PCh. 13 - The 400-lb cylinder at A is hoisted using the...Ch. 13 - Prob. 43PCh. 13 - Prob. 46PCh. 13 - Prob. 47PCh. 13 - Prob. 48PCh. 13 - Prob. 51PCh. 13 - The block rests at a distance of 2 m from the...Ch. 13 - Determine the maximum speed that the jeep can...Ch. 13 - A pilot weighs 150 lb and is traveling at a...Ch. 13 - The sports car is traveling along a 30 banked road...Ch. 13 - If the 10-kg ball has a velocity of 3m/ s when it...Ch. 13 - Prob. 12FPCh. 13 - Prob. 53PCh. 13 - The 2-kg block B and 15-kg cylinder A are...Ch. 13 - Determine the maximum constant speed at which the...Ch. 13 - Cartons having a mass of 5 kg are required to move...Ch. 13 - The 2-kg spool S fits loosely on the inclined rod...Ch. 13 - Prob. 59PCh. 13 - Prob. 60PCh. 13 - At the instant B = 60, the boys center of mass G...Ch. 13 - Prob. 62PCh. 13 - Prob. 66PCh. 13 - The 150-lb man lies against the cushion for which...Ch. 13 - The 150-lb man lies against the cushion for which...Ch. 13 - Prob. 76PCh. 13 - Prob. 80PCh. 13 - Prob. 81PCh. 13 - Determine the constant angular velocity of the...Ch. 13 - The 0.2-kg ball is blown through the smooth...Ch. 13 - The 2-Mg car is traveling along the curved road...Ch. 13 - The 0.2-kg pin P is constrained to move in the...Ch. 13 - Determine the magnitude of the resultant force...Ch. 13 - The path of motion of a 5-lb particle in the...Ch. 13 - The boy of mass 40 kg is sliding down the spiral...Ch. 13 - Using a forked rod, a 0.5-kg smooth peg P is...Ch. 13 - The collar has a mass of 2 kg and travels along...Ch. 13 - The forked rod is used to move the smooth 2-lb...Ch. 13 - Prob. 109PCh. 13 - Prob. 110PCh. 13 - Prob. 113PCh. 13 - A communications satellite is in a circular orbit...Ch. 13 - Prob. 115PCh. 13 - Prob. 117PCh. 13 - Prob. 118PCh. 13 - Prob. 119PCh. 13 - The rocket is in free flight along an elliptical...Ch. 13 - Prob. 123PCh. 13 - Prob. 124PCh. 13 - Prob. 129PCh. 13 - Prob. 130PCh. 13 - Prob. 131PCh. 13 - The rocket is traveling around the earth in free...Ch. 13 - Prob. 1RPCh. 13 - Prob. 2RPCh. 13 - Block B rests on a smooth surface. If the...Ch. 13 - Prob. 4RPCh. 13 - Prob. 5RPCh. 13 - The bottle rests at a distance of 3ft from the...Ch. 13 - Prob. 7RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The hollow tube assembly rotates about a vertical axis with a constant angular velocity of 6 rad/s. A small 2.3-kg slider P moves inside the smooth horizontal tube portion under the control of the string which passes out the bottom of the assembly. The slider is pulled in towards O at a constant rate of 0.31 m/s. What is the tension in the cord when r= 0.15 m? Die hol buiseenheid roteer om 'n vertikale as met 'n konstante hoeksnelheid van 6 rad/s. 'n Klein 2.3-kg skuifstuk P beweeg binne in die gladde horisontale buisgedeelte onder die beheer van die tou wat aan die onderkant van die eenheid uitsteek. Die skuifstuk word teen 'n konstante tempo van 0.31 m/s na O ingetrek. Wat is die spanning in die koord as r = 0.15 m?arrow_forward3/46 The rod of the fixed hydraulic cylinder is moving to the left with a speed of 100 mm/s and this speed is momentarily increasing at a rate of 400 mm/s each sec- ond at the instant when sa = 425 mm. Determine the tension in the cord at that instant. The mass of slider B is 0.5 kg, the length of the cord is 1050 mm, and the effects of the radius and friction of the small pulley at A are negligible. Find results for cases (a) negligible friction at slider B and (6) µz = 0.40 at slider B. The action is in a vertical plane. 250 mm 0.5 kg B Problem 3/46arrow_forwardIf the motor draws in the cable with an acceleration of 3 m/s^2, determine the reactions at the supports A and B. The beam has a uniform mass of 30 kg/m, and the crate has a mass of 200 kg. Neglect the mass of the motor and pulleys.arrow_forward
- The "flying car" is a ride at an amusement park which consists of a car having wheels that roll along a track mounted inside a rotating drum. By design the car cannot fall off the track, however motion of the car is developed by applying the car's brake, thereby gripping the car to the track and allowing it to move with a constant speed of the track, vt = 3 m/s. The rider applies the brake when going from B to A and then releases it at the top of the drum, A, so that the car coasts freely down along the track to B (0 = π rad). Neglect friction during the motion from A to B. The rider and car have a total mass of 390 kg and the center of mass of the car and rider moves along a circular path having a radius of R = 9.8 m. (Figure 1) Figure R Barrow_forwardThe M engine of the elevator in the figure operates with an efficiency of 0.75. Determine the force required to be supplied to the motor to lift the 425 N box C, so that the P point on the rope will be pulled with an acceleration of 1.35 m / s2 and its speed at the moment shown is 0.7 m / s. Neglect the mass of the spool and rope. Pi M SCarrow_forwardA truck of mass 10 tonnes was moving with a velocity of 130 km/hr. The brakes were applied to bring the truck to 10 km/hr in 500 m. Determine the uniform force exerted by the brakes. Also find the velocity it will reach if the same force is applied in the same direction for 10.5 seconds and also find the distance travelled in this period. (Enter only the values in the boxes by referring the units given in bracket. Also upload the hand written copy in the link provided) The uniform force exerted by the brakes in N is The velocity it will reach if the same force is applied in the same direction for 10.5 seconds in m/s is The distance travelled if the same force is applied in the same direction in this period in m isarrow_forward
- The weight of the spring held follower AB is 0.381 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.2 ft and z = (0.1sin20) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force, in Ib, at the end A of the follower where e = 45°. In this position, the spring is compressed 0.4 ft. Neglect friction at the bearing C. Round your answer to 3 decimal places. z = 0.1 sin 20 0.2 ft e = 6 rad/s A k = 12 lb/ftarrow_forwardThe 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P= 100N inclined at 20o with the horizontal. Find the velocity of the block after it moves 20m starting from rest.arrow_forwardQ2) The slotted arm pivots about O and maintains the relation between the motions of sliders A and B and their control rods. Each small pivoted block is pinned to its respective slider and is constrained to slide in its rotating slot. Show that the displacement x is proportional to the reciprocal of y. Then estab- lish the relation between the velocities vA and vg. Also, if v, is constant for a short interval of motion, determine the acceleration of B. b y 'Barrow_forward
- The 5.27 kg collar B rests on the frictionless arm AA! The collar is held in place by the rope attached to drum D and rotates about O in a horizontal plane. The linear velocity of the collar B is increasing according to v = 0.2 t2 where v is in m/s and tis in seconds. Find the tension in the rope and the force of the bar on .the collar if 5 s,r= 0.558 m and 0 = 58° A A' Darrow_forwardThe 100-kg crate is hoisted by the motor M. If the velocity of the crate increases uniformly from 1.5 m/s to 4.5 m/s in 5 s, determine the tension developed in the cable during the motionarrow_forwardA Ferris wheel provides car A (120 kg) a constant increase of speed of a = 10 m/s . In order to determine the sizes of bolts to be used for the pin connection at A, calculate the horizontal and vertical components of the reaction when the speed reaches v = 15m/s p-4marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY