THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<
9th Edition
ISBN: 9781266657610
Author: CENGEL
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13.3, Problem 83P
Is it possible for an adiabatic liquid-vapor separator to separate wet steam at 100 psia and 90 percent quality, so that the pressure of the outlet streams is greater than 100 psia?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A single-effect evaporator is being used to concentrate 8000 kg/h of tomato juice from 5% total solids to 30% total solids. The juice enters the evaporator at 25°C. The evaporator is operated with steam (85% quality) at 143.27 kPa. The vacuum inside the evaporator allows the juice to boil at 75°C. Calculate (a) the steam requirements and (b) steam economy for the process. Assume the condensate is discharged at 75°C. The specific heat of the liquid feed is 4.1 kJ/(kg°C) and the concentrated product is 3.1 kJ/(kg°C).
1. A refrigeration system using R-22 has a capacity of 320 kW of refrigeration.
The evaporating temperature is -10°C and the condensing temperature is
40°C. Calculate the fraction of vapor in the mixture before the evaporator.
Properties of R-22:
At -10°C; hg = 401.60 kJ/kg, hf = 188.43 kJ/kg
At 40°C; hf 249.69 kJ/kg
Indonesia
Inggris
A single effect evaporator was used to concentrate 8000 kg / hr of tomato juice from 5% total solids to 30% total solids. The juice enters the evaporator at 25 ° C. The evaporator is operated on Steam (85% quality) at 143.27 kPa. The vacuum in the evaporator allows the juice to boil at 75 ° C. The specific heat of the dilute material is 4.1 kJ / (kg ° C) and the concentrate product is 3.1 kJ / (kg ° C). Count it (a) The rate of demand for steam? b. Steam economy if condensate temperature is released at 75 ° C.?
Chapter 13 Solutions
THERMODYNAMICS (LL)-W/ACCESS >CUSTOM<
Ch. 13.3 - What are mass and mole fractions?Ch. 13.3 - Consider a mixture of several gases of identical...Ch. 13.3 - The sum of the mole fractions for an ideal-gas...Ch. 13.3 - Somebody claims that the mass and mole fractions...Ch. 13.3 - Consider a mixture of two gases. Can the apparent...Ch. 13.3 - What is the apparent molar mass for a gas mixture?...Ch. 13.3 - Prob. 7PCh. 13.3 - The composition of moist air is given on a molar...Ch. 13.3 - Prob. 9PCh. 13.3 - Prob. 10P
Ch. 13.3 - A gas mixture consists of 20 percent O2, 30...Ch. 13.3 - Prob. 12PCh. 13.3 - Prob. 13PCh. 13.3 - Consider a mixture of two gases A and B. Show that...Ch. 13.3 - Is a mixture of ideal gases also an ideal gas?...Ch. 13.3 - Express Daltons law of additive pressures. Does...Ch. 13.3 - Express Amagats law of additive volumes. Does this...Ch. 13.3 - Prob. 18PCh. 13.3 - How is the P-v-T behavior of a component in an...Ch. 13.3 - Prob. 20PCh. 13.3 - Prob. 21PCh. 13.3 - Prob. 22PCh. 13.3 - Consider a rigid tank that contains a mixture of...Ch. 13.3 - Prob. 24PCh. 13.3 - Is this statement correct? The temperature of an...Ch. 13.3 - Is this statement correct? The volume of an...Ch. 13.3 - Is this statement correct? The pressure of an...Ch. 13.3 - A gas mixture at 300 K and 200 kPa consists of 1...Ch. 13.3 - Prob. 29PCh. 13.3 - Separation units often use membranes, absorbers,...Ch. 13.3 - Prob. 31PCh. 13.3 - The mass fractions of a mixture of gases are 15...Ch. 13.3 - The volumetric analysis of a mixture of gases is...Ch. 13.3 - An engineer has proposed mixing extra oxygen with...Ch. 13.3 - A rigid tank contains 0.5 kmol of Ar and 2 kmol of...Ch. 13.3 - A mixture of gases consists of 0.9 kg of oxygen,...Ch. 13.3 - Prob. 37PCh. 13.3 - One pound-mass of a gas whose density is 0.001...Ch. 13.3 - A 30 percent (by mass) ethane and 70 percent...Ch. 13.3 - Prob. 40PCh. 13.3 - Prob. 41PCh. 13.3 - A rigid tank that contains 2 kg of N2 at 25C and...Ch. 13.3 - Prob. 43PCh. 13.3 - Prob. 44PCh. 13.3 - Prob. 45PCh. 13.3 - Is the total internal energy of an ideal-gas...Ch. 13.3 - Prob. 47PCh. 13.3 - Prob. 48PCh. 13.3 - Prob. 49PCh. 13.3 - Prob. 50PCh. 13.3 - The volumetric analysis of a mixture of gases is...Ch. 13.3 - A mixture of nitrogen and carbon dioxide has a...Ch. 13.3 - The mass fractions of a mixture of gases are 15...Ch. 13.3 - A mixture of gases consists of 0.1 kg of oxygen, 1...Ch. 13.3 - An insulated tank that contains 1 kg of O2at 15C...Ch. 13.3 - An insulated rigid tank is divided into two...Ch. 13.3 - Prob. 59PCh. 13.3 - A mixture of 65 percent N2 and 35 percent CO2...Ch. 13.3 - Prob. 62PCh. 13.3 - Prob. 63PCh. 13.3 - Prob. 66PCh. 13.3 - Prob. 67PCh. 13.3 - Prob. 68PCh. 13.3 - Prob. 69PCh. 13.3 - The gas passing through the turbine of a simple...Ch. 13.3 - Prob. 71PCh. 13.3 - A pistoncylinder device contains 6 kg of H2 and 21...Ch. 13.3 - Prob. 73PCh. 13.3 - Prob. 74PCh. 13.3 - Prob. 75PCh. 13.3 - Prob. 76PCh. 13.3 - Prob. 77PCh. 13.3 - Prob. 78PCh. 13.3 - Prob. 79PCh. 13.3 - Prob. 81PCh. 13.3 - Fresh water is obtained from seawater at a rate of...Ch. 13.3 - Is it possible for an adiabatic liquid-vapor...Ch. 13.3 - Prob. 84PCh. 13.3 - Prob. 85RPCh. 13.3 - The products of combustion of a hydrocarbon fuel...Ch. 13.3 - A mixture of gases is assembled by first filling...Ch. 13.3 - Prob. 90RPCh. 13.3 - Prob. 91RPCh. 13.3 - Prob. 92RPCh. 13.3 - A rigid tank contains a mixture of 4 kg of He and...Ch. 13.3 - A spring-loaded pistoncylinder device contains a...Ch. 13.3 - Prob. 95RPCh. 13.3 - Reconsider Prob. 1395. Calculate the total work...Ch. 13.3 - Prob. 97RPCh. 13.3 - Prob. 100RPCh. 13.3 - Prob. 101RPCh. 13.3 - Prob. 102FEPCh. 13.3 - An ideal-gas mixture whose apparent molar mass is...Ch. 13.3 - An ideal-gas mixture consists of 2 kmol of N2and 4...Ch. 13.3 - Prob. 105FEPCh. 13.3 - Prob. 106FEPCh. 13.3 - An ideal-gas mixture consists of 3 kg of Ar and 6...Ch. 13.3 - Prob. 108FEPCh. 13.3 - Prob. 109FEPCh. 13.3 - Prob. 110FEPCh. 13.3 - Prob. 111FEP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Additional Instructions: Define each enthalpy obtained from tables and chart and draw the p-h diagram labeling the respective evaporating and condensing pressures and temperatures in each problem. (2) A standard vapor compression system produces 20 tons of refrigeration using R-12 as a refrigerant while operating between a condenser temperature of 41.6 C and an evaporator temperature of -25°C. Determine (a) the refrigerating effect in kJ/kg, (b) the circulating rate in kg/s, (c) the power supplied, (d) the COP, (e) the heat rejected in kW, and (f the volume flow rate in L/s. Ans. (a) 100.26 kJ/kg, (b) 0.7022 kg/s, (c) 25.69 kW, (d) 2.74, (e) 96.09 kW, (f) 92.18 L/sarrow_forwardConsider the vapor-compression refrigeration cycle shown below with tetrafluoroethane as the refrigerant. If the evaporation temperature is -12°C, determine the coefficients of performance for condensation temperatures of 16°C, 28°C, and 40°C. Use the table containing the properties of saturated 1,1,1,2- tetrafluoroethane (R134A) and the PH diagram for tetrafluoroethane (HFC-134a). T S Vapor-compression refrigeration cycle. 4 Throttle valve Condenser Compressor Evaporator Assume isentropic compression of the vapor. The coefficient of performance for a condensation temperature of 16°C is The coefficient of performance for a condensation temperature of 28°C is 3 The coefficient of performance for a condensation temperature of 40°C is 2arrow_forwardA single-effect evaporator concentrates 4.00 kg/s of a 10% by mass solution of H2SO4. The entering feed is at 25 °C. The vapor released at the top has a mass flow rate of 3.20 kg/s. The evaporator operates at a total pressure of 30.2 kPa at 90 °C. What is the rate of heat transfer in the evaporator? Use a steam table for the enthalpy of the vapor?arrow_forward
- Steam is expanded in the high pressure turbine from 4000kPa, 360°C to 1000kPa with an isentropic efficiency of 80%. The steam is then reheated isobarically to 360°C after which it passes through the low pressure turbine expanding down to 4kPa with an isentropic efficiency of 75%. If the condensate has a temperature of 24°C, calculate: (a). the condition of the steam entering the reheater (b). the condition of the steam entering the condenser (c). the total power output for a mass flow-rate of 10tonnes of steam per hour (d). the specific steam consumption in kg steam/kWh (e). the Rankine efficiency of the plant including the feed pump workarrow_forwardA two-stage ammonia food-freezing plant – with a desired capacity of 528,000 kJ/h at -40℃ evaporating temperature and 35C condensing temperature – has a flash intercooling system with a liquid sub cooler. The vapour leaving the evaporator is at -30℃ and entering the first stage compressor is at -15℃. The vapour leaving the flash chamber is superheated by 10℃ in the suction line to the second stage compressor. Water intercooling is done to cool the vapour to 45℃. Adiabatic efficiencies of both compressors are 0.65 and 0.77 respectively. Find the piston displacements, discharge temperatures and power requirements of the two compressors.arrow_forwardاريد حل كتابة يدarrow_forward
- Please show full working in stepsarrow_forwardRice at 35% moisture is to be dried to produce 500 lb/hr with 5% moisture. The air at 85 C and 30% RH is a mixture of outside air at 77 F and recirculated air coming from the drier is reheated to 113 C before entering the dryer and leaves at 100 C and 60 % RH. The steam that is used to reheat the air enters and leaves the reheater saturated at 75 psi. Determine: (a) the amount of feed in lb/hr. (b) the amount of air in lb/hr. (c) the amount of steam needed to reheat the air in lb/hr.arrow_forwardAtmospheric air at 40°C dbt and 55% RH is passed over a cooling coll at the rate of 600 m/mint. At exit from coil the air is saturated and its temperature is 8°C. The condensate also leaves at 8°C. Determine the amount of condensate leaving coll per minute and refrigeration in kW. The specific heat of superheated steam may be assumed to be 1.88 kJ/kg-K. Solve the problem without psychromatic chart.arrow_forward
- Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 7. Determine the quality of steam at the condenser inlet.arrow_forward300 kg/min of water is required to be cooled from 50°C to 25°C in a wet cooling tower. For these purposes, 730 m3/min of atmospheric air is circulated through it at countercurrent. If the atmosphere is at a pressure of 94 kPa and the dry bulb and humid are 25°C and 15°C, respectively, and in the mixing process 3.7% of water is lost per evaporation, determine*:a) Relative and absolute humidity and dew temperature of the atmosphere.b) Absolute humidity and temperature of the air at the outlet.arrow_forwardA 2 kg/sec of steam is delivered to the turbine at 5 MPa and 600 degree celsius. Before condensation at 30 degree celsius, steam is extracted for feed water heating in the Closed feedwater heater with drain pump forward at 0.65 MPa. Determine the following: (a) mass flowrate of extracted steam in kg/sec, (b) Heat added in kJ/min (c) Heat rejected in kJ/min, (d) Ideal turbine work, (e) Pump work in KW, and (f) thermale efficiencyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer [Conduction, Convection, and Radiation]; Author: Mike Sammartano;https://www.youtube.com/watch?v=kNZi12OV9Xc;License: Standard youtube license