EBK APPLIED FLUID MECHANICS
7th Edition
ISBN: 9780100668348
Author: UNTENER
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 14, Problem 14.36PP
To determine
The design of the channel cross-sections for the shapes shown in Table 14.3.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
1. What are the main factors influencing the flow velocity in an open channel? Explain how each factor affects the flow?
Compute for the specific energy of a rectangular channel having a flow of 1.8 cubic meter/sec. The channel. Is 3 meters wide and 0.8 meters deep. Elevation of the channel bed is 15.28m
Water flows at a depth of 0.7 m and velocity of 3 m/s in a 4-m wide rectangular channel when it encounters a sudden expansion that increased the channel width to 5 meters. What will happen to the water surface at the expansion?
a. It will go up
b. It will go down
c. It will remain at the same level
d. It will undergo a hydraulic jump
Chapter 14 Solutions
EBK APPLIED FLUID MECHANICS
Ch. 14 - Compute the hydraulic radius for a circular drain...Ch. 14 - A rectangular channel has a bottom width of 2.75...Ch. 14 - A drainage structure for an industrial park has a...Ch. 14 - Repeat Problem 14.3 lO if the side slope is 45Ch. 14 - Compute the hydraulic radius for a trapezoidal...Ch. 14 - Compute the hydraulic radius for the section shown...Ch. 14 - Repeat Problem 14.6 for a depth of 3.50 in.Ch. 14 - Compute the hydraulic radius for the channel shown...Ch. 14 - Compute the hydraulic radius for the channel shown...Ch. 14 - Water is flowing in a formed, unfinished concrete...
Ch. 14 - Determine the normal discharge for an aluminum...Ch. 14 - A circular culvert under a highway is 6 ft in...Ch. 14 - A wooden flume is being built to temporarily carry...Ch. 14 - A storm drainage channel in a city where heavy...Ch. 14 - Figure 14.21 represents the approximate shape of a...Ch. 14 - Calculate the depth of flow of water in a...Ch. 14 - Calculate the depth of flow in a trapezoidal...Ch. 14 - A rectangular channel must carry 2.0m3/s of water...Ch. 14 - The channel shown in Fig. 14.22 has a surface of...Ch. 14 - A square storage room is equipped with automatic...Ch. 14 - The flow from two of the troughs described in...Ch. 14 - For a rectangular channel with a bottom width of...Ch. 14 - It is desired to carry 2.00m3/s of water at a...Ch. 14 - For the channel designed in Problem 14.23, compute...Ch. 14 - Prob. 14.25PPCh. 14 - Prob. 14.26PPCh. 14 - A trapezoidal channel has a bottom width of 2.00...Ch. 14 - For the channel described in Problem 14.27,...Ch. 14 - Repeat Problem 14.28, except that the channel is...Ch. 14 - A trapezoidal channel has a bottom width of 2.00...Ch. 14 - Prob. 14.31PPCh. 14 - Compute the flow area and hydraulic radius for a...Ch. 14 - Prob. 14.33PPCh. 14 - Prob. 14.34PPCh. 14 - Prob. 14.35PPCh. 14 - Prob. 14.36PPCh. 14 - Prob. 14.37PPCh. 14 - Prob. 14.38PPCh. 14 - A rectangular channel 2.00 m wide carries 5.5m3/s...Ch. 14 - Prob. 14.40PPCh. 14 - A triangular channel with side slopes having a...Ch. 14 - A trapezoidal channel with a bottom width of 3.0...Ch. 14 - Prob. 14.43PPCh. 14 - Determine the required length of a contracted weir...Ch. 14 - Prob. 14.45PPCh. 14 - Prob. 14.46PPCh. 14 - Compare the discharges over the following weirs...Ch. 14 - Prob. 14.48PPCh. 14 - For a Parshall flume with a throat width of 9 in,...Ch. 14 - Prob. 14.50PPCh. 14 - A flow rate of 50ft3/s falls within the range of...Ch. 14 - Prob. 14.52PPCh. 14 - A long-throated flume is installed in a...Ch. 14 - Prob. 14.54PPCh. 14 - Prob. 14.55PPCh. 14 - Prob. 14.56PPCh. 14 - Prob. 14.57PPCh. 14 - For a long-throated flume of design B in a...Ch. 14 - For a long-throated flume of design C in a...Ch. 14 - Prob. 14.60PPCh. 14 - Prob. 14.61PP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water is flowing in an open channel at a depth of 2 m and breadthof 3 m and a velocity of 3 m/s. What is the flow rate at thechannel?arrow_forwardWater is to be transported in a cast iron rectangular channel with a bottom width of 6 ft at a rate of 70 ft3/s. The terrain is such that the channel bottom drops 2.1 ft per 1000 ft length. Determine the minimum height of the channel under uniform-flow conditionsarrow_forwardCompute for the critical depth in a channel with constant spesific energy of 5cm in a channel with 2.5 width and flow of 2m/secarrow_forward
- Water is to be transported in an unfinished-concrete rectangular channel with a bottom width of 4 ft at a rate of 51 ft3/s. The terrain is such that the channel bottom drops 2 ft per 1000 ft length. Determine the minimum height of the channel under uniform-flow conditions. What would your answer be if the bottom drop is just 1 ft per 1000 ft length?arrow_forwardWater flows in a rectangular channel with a width of 2.5 m. The kinetic energy correction coefficient (i.e. velocity coefficient) is estimated as a = 1.2. If the flow rate is 5 m³/s and the flow depth is 1.5 m: (a) determine the specific energy of the flow. (b) Calculate the alternate depth considering α = 1.0.arrow_forwardWater flows in an open channel across a weir which occupies the full width of the channel. The lenght of the weir is 0.5 m and the height of water over the weir is 100 mm. What is the flow rate of water?arrow_forward
- A rectangular channel is 3m wide and has a depth of flow of 1.5m. The channel roughness can be assumed to be 0.015 and the bed slope is 0.001. Calculate The height by which the bed should be raised to just produce critical depth The width by which the bed should be narrowed to just produce critical deptharrow_forwardWater at 15°C flows at a depth of 0.25 m with an average velocity of 7 m/s in a rectangular channel. Determine (a) the critical depth, (b) the alternate depth, and (c) the minimum specific energy.arrow_forwardConsider the same rectangular channel as in the previous problem (4.0 m wide, filled with water to 6.0 m, and walls of corrugated metal). If the slope is 0.65°, estimate the volume flow rate of the water.arrow_forward
- The best hydraulic cross section for a rectangular open channel is one whose fluid height is (a) half, (b) twice, (c) equal to, or (d) one-third the channel width.arrow_forwardWater flows in a rectangular open channel with constant channel width at 1 m depth, 0.8 m/s velocity. Determine the water depth of the channel when the flow velocity changed to 1.6 m/s.arrow_forwardWater at 20°C flows in a partially full 4-m-diameter circular channel at an average velocity of 2 m/s. If the maximum water depth is 1 m, determine the hydraulic radius, the Reynolds number, and the flow regime.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License