Concept explainers
List at least two common examples of fans, of blowers, and of compressors.
The examples of fans.
The examples of blowers.
The examples of compressors.
Explanation of Solution
Conclusion:
A fan is a machine which is used to create flow within a fluid typically a gas such as air. And the examples of fans are ceiling fans, the cooling fan in computers, table fans and propellers.
A blower is a machine which is used to generate the flow of air at different pressures and the examples of blowers are hairdryers, air blowers used in the furnace, automobile ventilation systems and leaf blowers.
The compressor is a mechanical device which increases the outlet pressure of the fluid and the examples of compressors are refrigerator and air conditioner compressors and air compressors used to inflate the tire of the automobiles.
Want to see more full solutions like this?
Chapter 14 Solutions
Fluid Mechanics Fundamentals And Applications
- Large hydroturbines achieve overall efficiencies above 95%, while the best efficiency of large pumps is a little more than 90%. Discuss some reasons for this to happen.arrow_forwardA turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. After resolving the turbine speed, what horsepower would be developed under a head of 11 meters?arrow_forwardCalculate the available suction head height of the centrifugal pump from the following data: (1) The atmospheric pressure is 730 V mm of mercury, (2) the head loss in the suction pipe (including friction loss and accessories loss, etc. is 2.95 meters, ( 3) The speed in the water suction pipe is 1.6m/sec, (4) the water temperature is 30°C.arrow_forward
- A fan when driven by a 5.8 Hp motor at a speed of 800 rpm delivers 510 m3/min at a total pressure of 5 cm water gage. If in the same installation, 6.5 cm water gage pressure is required. What power will the fan be driven?arrow_forwardProperties of jet obtained from orifice, from notches, from weirsarrow_forwardDescribe the geometry and operation of a human peristalticPDP that is cherished by every romantic person on earth.How do the two ventricles differ?arrow_forward
- Define the Maximum Power Generation by a Wind Turbine.arrow_forwardThe net head delivered by a pump at a rotational speed of 1000 rpm is 10 m. If the rotational speed is doubled, the net head delivered will be (a) 5 m (b) 10 m (c) 20 m (d ) 40 m (e) 80 marrow_forwardSketch and discuss in great detail the different pump curves including supply curve, system curve and efficiency curve.arrow_forward
- The original design of a hydraulic turbine has data as follows: flow rate of 1 cumex, effective head of 50 m, and runner diameter of 1.5 m. If the same turbine design is to be used in another application where the available flow is 2.5 cumex and effective head is 75 m, what would be the runner diameter (in meters) for this new application?arrow_forwardGive at least two reasons why turbines often have greater efficiencies than do pumps.arrow_forwardExplain in detail the positioning and environmental impact of large wind turbinesarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY