Concept explainers
The rating of speed reducer for power
The rating of speed reducer for nitrided power
Answer to Problem 26P
The rating of speed reducer for power is
The rating of speed reducer for nitrided power is
Explanation of Solution
Write the expression for diameter of pinion.
Here, the number of teeth on pinion is
Write the expression for diameter of the gear.
Here, the number of teeth on gear is
Write the expression for velocity of the pinion.
Here, the number of rotation made by pinion is
Write the expression for constant of transmission accuracy level number.
Here, the transmission accuracy level number is
Write the expression for constant
Write the expression for dynamic factor.
Write the expression for allowable bending stress number through hardened steels.
Here, the brinel hardness number is
Write the expression for stress cycle factor for bending.
Here, the number of cycles is
Write the expression for allowable stress.
Here, the reliability factor is
Write the expression for load correction factor for uncrowned teeth.
Write the expression for pinion proportion factor.
Here, the face width is
Write the expression for pinion proportion modifier for straddle mounted pinion.
Write the expression for mesh alignment factor.
Here, the empirical constant is
Write the expression for mesh alignment correction factor.
Write the expression for load distribution factor
Write the expression for overload factor for pinion.
Write the expression for overload factor for gear.
Write the expression for transmitted load in pinion.
Here, the spur gear geometry factor is
Write the expression for power for pinion.
Write the expression for transmitted load for gear.
Write the expression for power for gear.
Write the expression for gear ratio.
Here, the number of teeth on gear is
Write the expression for pitting resistance stress cycle factor for pinion.
Write the expression for pitting resistance stress cycle factor for gear.
Write the expression for geometry factor.
Here, the pressure angle is
Write the expression for hardness ratio factor
Write the expression for contact fatigue strength for pinion.
Write the expression for contact fatigue strength for gear.
Write the expression for pinion contact endurance strength.
Write the expression for transmitted load.
Write the expression for power of pinion.
Write the expression for gear contact strength.
Write the expression for transmitted load.
Her, the elastic coefficient is
Write the expression for power of gear.
Write the expression for contact fatigue strength for pinion for nitride.
Write the expression for contact fatigue strength for gear.
Write the expression for pinion contact endurance strength.
Write the expression for transmitted load.
Write the expression for power of pinion.
Write the expression for gear contact strength.
Write the expression for transmitted load.
Her, the elastic coefficient is
Write the expression for power of gear.
Write the expression for rated power.
Write the expression for rated power for nitrided.
Conclusion:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Refer to table 14-9, “Empirical constant
Substitute
Substitute
Refer Figure 14-6, “spur gear geometry factor”, to obtain the geometry factor for number of teeth
Since the thickness of gear is constant so
Since the loading is uniform so
Refer table 14-2, “values of the lewis form factor
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Thus, the rating of speed reducer for power is
Substitute
Thus, the rating of speed reducer for nitrided power is
Want to see more full solutions like this?
Chapter 14 Solutions
SHIGLEY'S MECHANICAL ENG.DESIGN W/CODE
- The gears of a gear wheel with a module of 4 mm, width of 60 mm and number of 18 teeth were broken during operation. If the gear wheel is made of cast iron (GG-25), with what torque is it loaded? Given: Speed factor Kv= 1.25; kuarrow_forwardProvide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4arrow_forwardA 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear. Part A Find the appropriate standard diametral pitch for the gearset. Part B Find the minimum required face width of the gears needed to satisfy the safety requirementsarrow_forward
- A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic loaarrow_forwardA helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.arrow_forwardA set of gears is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor, depicted below. The gear on the motor shaft is a 10-pitch pinion, has 18 teeth, and drives at 1200 rpm clockwise. The driven gear has 72 teeth. The motor has failed and is to be replaced with the only motor available, a 600 rpm motor with an 8-pitch pinion. Specify the set of commercially available 20⁰ spur gears, by number of teeth (N3and N4), that would result in the same conveyor speed and can be used without modification to the mounting (the center distance must not change). Find the number of teeth N3 on the pinion (drive) gear (teeth): Find the number of teeth N4 on the driven gear (teeth):arrow_forward
- What are the harmful effects of backlash error in gears?arrow_forwardTwo spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teetharrow_forwardA parallel-shaft gearset consists of an 18-tooth helical pinion driving a 32-tooth gear. The pinion has a left-hand helix angle of 20, a normal pressure angle of 25, and a normal module of 3 mm. Evaluate root diameter (mm) of the pinion. A) 51,21 B) 49,92 C) 50,00 D) 48,00 E) 52,08arrow_forward
- A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.arrow_forwardQ.8 A pair of helical gears in which teeth on pinion are 20 and on gear are 30, the normal module is 5 mm and normal pressure angle is 20°. The helix angle is 30°. The pinion is provided 5 kW at 720 rpm. Determine various forces on the teeth.arrow_forwardPlease answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY