Concept explainers
Whether the rated power is valid.
Answer to Problem 10P
The rated power is valid.
Explanation of Solution
Write the expression for pitch diameter of gear.
Here, the pitch diameter of gear is
Write the expression for pitch diameter of pinion.
Here, the pitch diameter of pinion is
Write the expression for gear ratio of gear set.
Here, the gear ratio is
Write the expression for pitch line velocity.
Here, the pitch line velocity is
Write the expression for dynamic factor.
Here, dynamic factor is
Write the expression for constant
Here, the transmission accuracy number is
Write the expression for constant
Write the expression of size factor for
Here, size factor is
Write the expression for size factor of pitting resistance for
Here, size factor for pitting resistance is
Write the expression for load distribution factor.
Here, load distribution factor is
Write the general expression for stress cycle factor of pinion for
Here, the stress cycle factor for pinion is
Write the general expression for stress cycle factor of gear for
Here, the stress cycle factor for gear is
Write the expression for reliability factor for bending strength.
Here, the reliability factor is
Write the expression for reliability factor for pitting.
Write the expression for stress cycle factor for pitting resistance for pinion for
Here, the stress cycle factor for pitting resistance for pinion is
Write the critical expression for stress cycle factor for pitting resistance for gear for
Here, the stress cycle factor for pitting resistance for gear is
Write the expression for hardness ratio factor for pitting resistance for gear.
Here, hardness ratio factor for pitting resistance for gear is
Write the expression for constant
Here, the Brinell harness number for pinion is
Write the expression for allowable bending stress number.
Here, the allowable bending stress number is
Write the expression for permissible bending stress for pinion.
Here, the permissible bending stress for pinion is
Write the expression for permissible bending stress for gear.
Here, the permissible bending stress for gear is
Write the expression for bending stress for pinion.
Here, the bending stress in pinion is
Write the expression for bending stress for gear.
Here, the bending stress in gear is
Write the expression for transmitted load by pinion in bending.
Here, the transmitted load by pinion in bending is
Write the expression for transmitted load on gear in bending.
Here, the transmitted load on gear in bending is
Write the expression for allowable contact stress number.
Here, the allowable bending stress number is
Write the expression for permissible contact stress number for pinion.
Here, the permissible contact stress number for pinion is
Write the expression for permissible contact stress number for gear.
Here, the permissible contact stress for gear is
Write the expression for contact stress for pinion.
Here, the contact stress in pinion is
Write the expression for contact stress for gear.
Here, the contact stress in gear is
Write the expression for transmitted load by pinion for wear.
Here, the transmitted load by pinion for wear is
Write the expression for transmitted load on gear for wear.
Here, the transmitted load on gear for wear is
Write the expression for crowning factor for pitting of uncrowned tooth.
Here, the crowning factor for pitting is
Conclusion:
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Substitute
Refer to Figure 15-7 “Bending factor
Substitute
Substitute
Substitute
Refer to Figure 15-7 “Bending factor
Substitute
Substitute
Substitute
Substitute
Refer to Table 14-8 “Elastic Coefficient
Refer to Figure 15-6 “Contact geometry factor
Substitute
Substitute
Substitute
Substitute
Substitute
The power rating for a gearset is defined as minimum of power rating in wear for pinion and gear and in bending for pinion and gear so that the failure by bending and wear of teeth on both gear and pinion can be saved.
The calculated power rating for gearset is
Thus, the rated power is valid.
Want to see more full solutions like this?
Chapter 15 Solutions
SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
- A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut. A.Determine the diametral pitch, B. face width, C. and tooth numbers if the material is cast iron, class 25arrow_forwardProvide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4arrow_forwardFor a pair of spur gears, one design decision is to specify the pressure angles. Please select the common values of pressure angle per textbook. 300 200 250arrow_forward
- 2) Two mating internal 10-pitch, spur gears have 16 and 86 teeth. Determine the center distance. 3) Two mating external 8-pitch, 20o , spur gears have 24 and 64 teeth. Determine the contact ratio. 4) Two mating 20°, 8-pitch, spur gears have 14 and 42 teeth. Will they interfere? 5) A pair of 20°, mild-steel gears are to be selected for an application where they need to transfer 5 hp. The pinion drives at 1800 rpm and the gear must rotate as close to 480 rpm as possible. Select a set of gears to accomplish this task. a) Determine a suitable diametral pitch and pressure angle. b) Use the required velocity ratio to iterate and determine appropriate number of teeth (confirm that these gears are commercially available). c) Calculate the pitch diameters and center distance.arrow_forwardDesign a pair of straight bevel gears to transmit 5.0 hp at a pinion speed of 850 rpm. the gear speed should be approximately 300 rpm. consider both strength and pitting resistance. the driver is a gasoline engine, and the driven machine is a heavy-duty conveyor.arrow_forward(b)A pair of straight bevel gears has a velocity ratio of 2:1. The pitch circle diameter of the pinion is 80 mm at the large end of the tooth.A5KW power is supplied to the pinion which rotates at 800 rp.m. The face width is 40 mm and the pressure angle is 20. Calculate the tangential ,radial and axial components of the resultant tooth force acting on the pinionarrow_forward
- A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.arrow_forwardA 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…arrow_forwardSolve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank youarrow_forward
- Design a pair of plastic gears to drive a small band saw, using the following data: The input is from a 0.5hp electric motor rotating at 1160 rpm. The pinion is mounted on its 0.75 in diameter shaft. The gear is rotating at 250 rpm. For design purposes, consider taking Np=18 (number teeth in pinion) and Pd = 12 (diametral pitch). In this case, the acceptable number of teeth in the gear should be: NG=58 teeth NG = 93 teeth NG = 84 teeth NG = 70 teetharrow_forwardThe figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.arrow_forwardDesign a two-stage compound spur gear train for an overall ratio of approximately 17+08:1. Specify tooth numbers for each gear in the train.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY