EP ENGR.MECH.-MOD.MASTERING ACCESS
15th Edition
ISBN: 9780134867267
Author: HIBBELER
Publisher: PEARSON CO
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 15, Problem 139P
The missile weighs 40 000 lb. The constant thrust provided by the turbojet engine is T = 15 000 lb. Additional thrust is provided by two rocket boosters B. The propellant in each booster is burned at a constant rate of 150 lb/s, with a relative exhaust velocity of 3000 ft/s. If the mass of the propellant lost by the turbojet engine can be neglected, determine the velocity of the missile after the 4-s burn time of the boosters. The initial velocity of the missile is 300 mi/h.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A launch vehicle has 6 engines operating in parallel which are fed from the same propellant tank.
Initially, each engine has an equivalent exhaust velocity of 3500 m/s and consumes 400 kilograms of
propellant per second.
One of the engines malfunctions and consequently operates at 50% thrust and 120% propellant
consumption. Calculate the equivalent exhaust velocity in m/s of all engines if treated as a single
engine, including the malfunctioning engine in your calculation.
The jet has a speed of 1260 km/hkm/h when it is flying horizontally. Air enters the intake scoop S� at the rate of 52 m3/sm3/s. The engine burns fuel at the rate of 1.85 kg/skg/s, and the gas (air and fuel) is exhausted relative to the plane with a speed of 2330 km/hkm/h. The plane has a mass of 8 MgMg. Assume that the air has a constant density of ρa�� = 1.112 kg/m3kg/m3. (Figure 1)
Determine the drag exerted on the plane by air resistance.
Express your answer to three significant figures and include the appropriate units.
Please write legibly.
Chapter 15 Solutions
EP ENGR.MECH.-MOD.MASTERING ACCESS
Ch. 15 - The 0.5kg ball strikes the rough ground and...Ch. 15 - Prob. 2FPCh. 15 - Prob. 3FPCh. 15 - The wheels of the 1.5-Mg car generate the traction...Ch. 15 - Prob. 5FPCh. 15 - If the coefficient of kinetic friction between the...Ch. 15 - Prob. 3PCh. 15 - Each of the cables can sustain a maximum tension...Ch. 15 - Crates A and B weigh 100 lb and 50 lb,...Ch. 15 - Prob. 8P
Ch. 15 - Prob. 9PCh. 15 - During operation the jack hammer strikes the...Ch. 15 - For a short period of time, the frictional driving...Ch. 15 - The 2.5-Mg van is traveling with a speed of 100...Ch. 15 - Prob. 14PCh. 15 - The towing force acting on the 400-kg safe varies...Ch. 15 - Prob. 18PCh. 15 - Prob. 19PCh. 15 - If it takes 35 s for the 50-Mg tugboat to increase...Ch. 15 - Prob. 23PCh. 15 - The balloon has a total mass of 400 kg including...Ch. 15 - Prob. 26PCh. 15 - Prob. 30PCh. 15 - Prob. 7FPCh. 15 - The cart and package have a mass of 20 kg and 5...Ch. 15 - The 5-kg block A has an initial speed of 5 m/s as...Ch. 15 - Prob. 10FPCh. 15 - Prob. 11FPCh. 15 - The cannon and support without a projectile have a...Ch. 15 - The 5-Mg bus B is traveling to the right at 20...Ch. 15 - Prob. 36PCh. 15 - A railroad car having a mass of 15 Mg is coasting...Ch. 15 - A ballistic pendulum consists of a 4-kg wooden...Ch. 15 - Prob. 39PCh. 15 - Prob. 43PCh. 15 - Prob. 44PCh. 15 - Prob. 45PCh. 15 - The 30-Mg freight car A and 15-Mg freight car B...Ch. 15 - Blocks A and B have masses of 40 kg and 60 kg,...Ch. 15 - Block A has a mass of 5 kg and is placed on the...Ch. 15 - Solve Prob. 15-53 if the coefficient of kinetic...Ch. 15 - Prob. 56PCh. 15 - Prob. 13FPCh. 15 - Prob. 14FPCh. 15 - The 30-lb package A has a speed of 5 ft/s when it...Ch. 15 - The ball strikes the smooth wall with a velocity...Ch. 15 - Prob. 17FPCh. 15 - Prob. 18FPCh. 15 - Prob. 58PCh. 15 - Prob. 59PCh. 15 - Prob. 61PCh. 15 - Prob. 62PCh. 15 - Prob. 63PCh. 15 - Prob. 64PCh. 15 - A 1-lb ball A is traveling horizontally at 20 ft/s...Ch. 15 - Prob. 69PCh. 15 - Prob. 73PCh. 15 - Two smooth disks A and B each have a mass of 0.5...Ch. 15 - Prob. 75PCh. 15 - The cue ball A is given an initial velocity (vA)1...Ch. 15 - Prob. 78PCh. 15 - Prob. 79PCh. 15 - A ball of negligible size and mass m is given a...Ch. 15 - Prob. 81PCh. 15 - The 20-lb box slides on the surface for which k =...Ch. 15 - Prob. 84PCh. 15 - Prob. 85PCh. 15 - Prob. 90PCh. 15 - Prob. 92PCh. 15 - Disks A and B have a mass of 15 kg and 10 kg,...Ch. 15 - Prob. 19FPCh. 15 - Prob. 20FPCh. 15 - Initially the 5-kg block is moving with a constant...Ch. 15 - Prob. 22FPCh. 15 - Prob. 23FPCh. 15 - Prob. 24FPCh. 15 - Determine the angular momentum HO of the 6-lb...Ch. 15 - Determine the angular momentum HP of the 6-lb...Ch. 15 - Prob. 96PCh. 15 - Determine the angular momentum Hp, of each of the...Ch. 15 - Prob. 98PCh. 15 - Determine the angular momentum Hp of the 3-kg...Ch. 15 - The 800-lb roller-coaster car starts from rest on...Ch. 15 - The 800-lb roller-coaster car starts from rest on...Ch. 15 - If the rod of negligible mass is subjected to a...Ch. 15 - The amusement park ride consists of a 200-kg car...Ch. 15 - An earth satellite of mass 700 kg is launched into...Ch. 15 - Prob. 115PCh. 15 - Prob. 116PCh. 15 - Prob. 119PCh. 15 - The gauge pressure of water at A is 150.5 kPa....Ch. 15 - Prob. 121PCh. 15 - The fountain shoots water in the direction shown....Ch. 15 - A plow located on the front of a locomotive scoops...Ch. 15 - Prob. 124PCh. 15 - Water is discharged from a nozzle with a velocity...Ch. 15 - Prob. 127PCh. 15 - Prob. 128PCh. 15 - Sand drops onto the 2-Mg empty rail car at 50 kg/s...Ch. 15 - Prob. 133PCh. 15 - A rocket has an empty weight of 500 lb and carries...Ch. 15 - Prob. 135PCh. 15 - Prob. 138PCh. 15 - The missile weighs 40 000 lb. The constant thrust...Ch. 15 - Prob. 140PCh. 15 - Prob. 1RPCh. 15 - Prob. 2RPCh. 15 - Prob. 3RPCh. 15 - Prob. 4RPCh. 15 - The 200-g projectile is fired with a velocity of...Ch. 15 - Block A has a mass of 3 kg and is sliding on a...Ch. 15 - Two smooth billiard balls A and B have an equal...Ch. 15 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (1) During a rockburst (violent rock failure underground), a rock block was ejected as a projectile from the tunnel wall at a height of 1.5 m and the block landed on the floor at a distance of 2.5 m from the left wall. Determine the ejection velocity ve for 0 = 20°. 1.5 m 2.5 marrow_forwardThe vane is moving at 80 ft/s when a jet of water having a velocity of 150 ft/s enters at A. The cross-sectional area of the jet is 1.5 in2, and it is diverted as shown Determine the horsepower developed by the water on the blade. 1hp = 550 ft*lb/sarrow_forwardPrinciple of Linear Impulse and Momentum for a System of Particles To apply the principle of linear impulse and momentum to a system of particles. Integrating the equation of motion, as applied to all particles in a system, yields ∑mi(vi)1+∑∫t2t1Fidt=∑mi(vi)2 where mi is the ith particle's mass, vi is the ith particle's velocity, and Fi is the external force that acts on the ith particle. This relationship states that the sum of the initial linear momenta, at time t1, and the impulses of all the external forces acting between times t1 and t2 is equal to the sum of the linear momenta of the system, at time t2. If the system has a mass center, G, the expression becomes m(vG)1+∑∫t2t1Fidt=m(vG)2 This expression allows the principle of linear impulse and momentum to be applied to a system of particles that is represented as a single particle. Two blocks, each of mass m = 6.90 kg , are connected by a massless rope and start sliding down a slope of incline θ = 36.0 ∘ at t=0.000 s. The…arrow_forward
- 5. The jet engines on an airplace must develop a certain amount of power to propel the airplane through the air with a speed of 280 km/h at a cruising altitude of 4,000 m. By what percent must the power be increased if the same airplane were to maintain its 280 km/h flight speed at 500 m altitude?arrow_forwardEach of the two stages A and B of the rocket has a mass of 2 M-g (M=mega) when their fuel tanks are empty. They each carry 300 kg of fuel and are capable of consuming it at a rate of 50 kg/s and eject it with a constant velocity of 2500 m/s, measured with respect to the rocket. The rocket is launched vertically from rest by first igniting stage B. Then stage A is ignited immediately after all the fuel in B is consumed and A has separated from B Neglect drag resistance and the variation of the rocket’s weight with altitude. Given: Ma = Mb = 2000 Kg M Fuel = 300 Kg Fuel Consumption = 50 Kg/s V0 Ejected Fuel = 2500 m/s V0 rocket = 0 m/sarrow_forwardA freight train is being assembled in a switching yard. Car 1 has a mass of m1 = 64x10^3 kg and moves at a velocity of 1 m/ s. Car 2, with a mass of m2= 87x10^2 kg and a velocity of 1 m/ s, overtakes car 1 and couples to it. Neglecting friction, find the common velocity vf of the cars after they become coupled.arrow_forward
- The second stage of a two-stage rocket weighs 2000 lb (empty) and is launched from the first stage with a velocity of 3000 mi/h. The fuel in the second stage weighs 1000 lb. If it is consumed at the rate of 50lb/s and ejected with a relative velocity of 8000 ft/s, determine the acceleration of the second stage just after the engine is fired. What is the rocket’s acceleration just before all the fuel is consumed? Neglect the effect of gravitation.arrow_forwardDuring the entry of the space shuttle into the earth’s atmosphere, maximum stagnation point heating occurs at the trajectory point corresponding to an altitude of 68.9 km, where ρ∞ = 1.075 × 10−4 kg/m3, and a flight velocity of 6.61 km/s. At this point on its entry trajectory, the shuttle is at a 40.2 degree angle of attack, which presents an effective nose radius at the stagnation point of 1.29 m. If the wall temperature is Tw = 1110 K, calculatethe stagnation point heating rate.arrow_forwardA motorcycle and rider have a combined mass of 350kg. The vehicle’s velocity is 100 km/hr. The rider is to go up a hill incline of 10 meters. The wheels each have a mass of 20 kg and a diameter of 500mm. The wheel design consists of 6 spokes with a mass of 0.5 kg for each spoke. Determine the vehicle’s velocity at the top of the hill, assuming it was a rolling vehicle with engine being turned off.arrow_forward
- The rocket shown is designed to test the operation of a new guidance system. When it has reached a certain altitude beyond the effective influence of the earth's atmosphere, its mass has decreased to 2.49 Mg, and its trajectory is 0= 34° from the vertical. Rocket fuel is being consumed at the rate of 130 kg/s with an exhaust velocity of 625 m/s relative to the nozzle. Gravitational acceleration is 9.54 m/s² at its altitude. Calculate the n- and t-components of the acceleration of the rocket. Answers: an= Vert. 18 at = M 1 Da - Horiz- m/s² m/s²arrow_forwardA spacecraft is moving in gravity-free space along a straight path when its pilot decides to accelerate forward. He turns on the thrusters, and burned fuel is ejected at a constant rate of 2.0 × 102 kg/s, at a speed (relative to the rocket) of 2.5 × 10² m/s. The initial mass of the spacecraft and its unburned fuel is 2.0 × 104 kg, and the thrusters are on for 30 s. a. What is the thrust (the force applied to the rocket by the ejected fuel) on the spacecraft? b. What is the spacecraft's acceleration as a function of time? c. What are the spacecraft's accelerations at t = 0, 15, 30, and 35 s?arrow_forwardOne part of an inspection system in a packaging operation uses an air blast to remove defective pieces of cardboard from the conveyor belt. The blast is initiated by a sensor and clocked so that the product is in front of the blast at just the right . The product is going to be dumped onto a shelf next to the conveyor belt. Determine the speed of the air jet required to tip the cardboard off the conveyor. The density of air is 1.10 kg/m3. The cardboard has a mass of 0.10 kg and the jet has a diameter of 10 mm.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY