Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 15, Problem 13RQ
What is the difference between piping and bambooing?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
144
About industrial piping, answer questions:
WHAT IS THE PURPOSE OF THE FORM COEFFICIENT FOR THE CALCULATION OF FLEXIBILITY?
What is the Mannesmann milling process? Why is the Mannesmann piercing process not capable of producing extremely long lengths of seamless tubing?
151 About industrial pipping:
HOW SHOULD ECONOMIC SPEEDS BE USED?
Chapter 15 Solutions
Manufacturing Engineering & Technology
Ch. 15 - How does extrusion differ from rolling and...Ch. 15 - Explain the difference between extrusion and...Ch. 15 - What is a spider die? What is it used for?Ch. 15 - Why are wires sometimes drawn in bundles?Ch. 15 - What is a dead-metal zone?Ch. 15 - Define the terms (a) cladding, (b) dummy block,...Ch. 15 - Why is glass a good lubricant in hot extrusion?Ch. 15 - What types of defects may occur in (a) extrusion...Ch. 15 - Describe the difference between direct and reverse...Ch. 15 - What is land? What is its function in a die?
Ch. 15 - How are tubes extruded? Can they also be drawn?...Ch. 15 - Prob. 12RQCh. 15 - What is the difference between piping and...Ch. 15 - What is impact extrusion?Ch. 15 - What is the pipe defect in extrusion?Ch. 15 - List the similarities and differences between...Ch. 15 - Explain why extrusion is a batch, or...Ch. 15 - The extrusion ratio, die geometry, extrusion...Ch. 15 - Explain why cold extrusion is an important...Ch. 15 - What is the function of a stripper plate in impact...Ch. 15 - Explain the different ways by which changing the...Ch. 15 - Glass is a good lubricant in hot extrusion. Would...Ch. 15 - How would you go about avoiding center-cracking...Ch. 15 - Table 15.1 gives temperature ranges for extruding...Ch. 15 - Will the force in direct extrusion vary as the...Ch. 15 - Comment on the significance of metal flow patterns...Ch. 15 - In which applications could you use the type of...Ch. 15 - What is the purpose of the land in a drawing die?...Ch. 15 - Can spur gears be made by (a) drawing and (b)...Ch. 15 - How would you prepare the end of a wire in order...Ch. 15 - What is the purpose of a dummy block in extrusion?...Ch. 15 - Describe your observations concerning Fig. 15.9.Ch. 15 - Occasionally, steel wire drawing will take place...Ch. 15 - Explain the advantages of bundle drawing.Ch. 15 - Under what circumstances would backward extrusion...Ch. 15 - Why is lubrication detrimental in extrusion with a...Ch. 15 - In hydrostatic extrusion, complex seals are used...Ch. 15 - Describe the purpose of a container liner in...Ch. 15 - Estimate the force required in extruding 7030...Ch. 15 - Assuming an ideal drawing process, what is the...Ch. 15 - Prob. 41QTPCh. 15 - Calculate the extrusion force for a round billet...Ch. 15 - Prob. 43QTPCh. 15 - A round wire made of a perfectly plastic material...Ch. 15 - Assume that the summary to this chapter is...Ch. 15 - Prob. 47SDPCh. 15 - Figure 15.2 shows examples of discrete parts that...Ch. 15 - The parts shown in Fig. 15.2 are economically...Ch. 15 - Survey the technical literature, and explain how...Ch. 15 - Prob. 51SDPCh. 15 - List the processes that are suitable for producing...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 22 About industrial piping, answer questions: FOR THE CALCULATION OF SPAN BETWEEN SUPPORTS, WHAT IS THE BASIC LIMITATION TO DEFINE THE MAXIMUM DISTANCE BETWEEN SPANS?arrow_forwardIndustrial Pipes Is the residual tightening given in screw cases intended to compensate for internal pressure and should be added to the initial tightening?arrow_forwardDescribe the defects found on the injection/ compression moulded parts with different temperatures or time setting. Discuss the possible causes for each case.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License