Concept explainers
A wheel moves in the
Fig. P15.248
Velocity of point P at
Answer to Problem 15.248RP
The velocity at point P is equal to
Explanation of Solution
Given information:
Point P is located on horizontal diameter.
The angular displacement is given as:
The linear displacement is given as:
The angular velocity
The linear velocity
Calculation:
According to given information:
Differentiate
At
Therefore
Then
Differentiate
At
Therefore, the velocity of point P is:
Conclusion:
At
The velocity at point P is equal to
Want to see more full solutions like this?
Chapter 15 Solutions
Vector Mechanics For Engineers
- A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is r=4.0m. The velocity of the plate C is VC=6.0 m/s to the right. The velocity of the plate D is VD=2.0 m/s to the left. Using the instantaneous center of zero velocity (IC) to determine (3) The magnitude of the angular velocity of the cylinder ω=____________rad/sarrow_forwardImagine that the CD on the right side is rotating with a constantangular velocity of �=6 rad/s between t=0 and t=3 s. Then, at t=3 s,it is suddenly subjected to a constant angular acceleration of α=6rad/s2 for 2 seconds. Determine the number of turns for the totaltime interval from t=0 to t=5 s. (Diameter of the CD is 12 cm)arrow_forwardIn the system shown in the figure, rod ab rotates at 5rad / s speed. When theta angle is 60 degrees, determine the velocity of block c.arrow_forward
- A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is r=4.0m. The velocity of the plate C is VC=6.0 m/s to the right. The velocity of the plate D is VD=2.0 m/s to the left. Using the instantaneous center of zero velocity (IC) to determine (1) The distance between point A and IC point, rA/IC=_____ marrow_forwardThe constant angular acceleration of the rotating disk is 12 rad/s . The angular velocity of the disk is 24 rad/s clockwise when t = 0. Determine the total angle turned by the disk between t = 0 and t = 4sec. the answer is 48 rad. show your solution.arrow_forwardHi, I need help with this question please. Block A is connected to a fixed pin O with a string 100 mm long. The block and the channel are at rest when a motor on a shaft through O starts to rotate the channel with angular velocity ω = sin(0.2t) rad/s and the string starts to pull the block towards O with speed v = sin(0.2t) mm/s. 1. At the time instant t = 2.5π s, determine: a) the components of the velocity and acceleration of the ball in polar coordinatesb) the speed of the ballc) the components of the velocity and acceleration of the ball in normal coordinatesd) sketch the polar and normal components of the velocity and acceleration of the ball on the figure.arrow_forward
- A train is moving horizontally to the right with the speed of VT=60 mi/h. Meanwhile, a car is traveling toward the train with the speed of VC=30 mi/h and a 30deg angle with respect to horizontal direction. Select the correct expression of the velocity vector of the train relative to the car ___________mi/h A. (60-30cos30°)-30sin30° B. (60-30cos30°) +30sin30° C. (60+30cos30°)-30sin30° D. (30cos30°-60) +30sin30°arrow_forwardThe rod is attached with ball-and-socket joints to smooth collars A and B at its end points. A is moving upward at a constant speed of vA = 6.4 ft/s . The angular velocity of the rod is directed perpendicular to the axis of the rod. Determine the magnitude of the velocity of B at the instant shown Determine the x, y, and z components of the angular velocity of the rod using scalar notation.arrow_forwardA disc rolls straight on a flat floor without slipping. The magnitude of the angular velocity ω= 3.0 rad/s, the angular acceleration α=2.0 rad/s2. The radius of the disc is r=1.0 m. b) Is the following statement true? Point A shown above is the instant center of zero velocity of the disk at the moment. True Falsearrow_forward
- The bar rotates about the fixed point ܱ with a constant angular velocity of 2 rad/s. Point A moves outwards along the bar at a constant rate of 100 mm/s. Point B is a fixed point on the bar. At the instant shown, what is the magnitude of the velocity of point A relative to point Barrow_forwardhow are the radial accelerations of points at the teeth of the two sprockets related? Explain.arrow_forwardCollars A and B are attached by a rod of length 30 cm, as shown below. The joint at A is a ball-and-socket and at B a pin joint. Collar A moves in the z direction, while the guide bar for collar B is on xy plane. At the instant shown, collar A is at a height of 24 cm and collar B is moving with a speed of 3 m/s towards the x axis. Find the (a) angular velocity of the rod, and (b) the sliding of collar B. Use the image attached to solve the questionarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY