Concept explainers
An uncrowned straight-bevel pinion has 30 teeth, a diametral pitch of 6, and a transmission accuracy number of 6. The driven gear has 60 teeth. Both are made of No. 30 cast iron. The shaft angle is 90°. The face width is 1.25 in, the pinion speed is 900 rev/min, and the normal pressure angle is 20°. The pinion is mounted outboard of its bearings and the bearings of the gear straddle it. What is the power rating based on AGMA bending strength? Note: For cast iron gearsets reliability information has not yet been developed. We say that if the life is greater than 107 revolutions, then set KL = 1, CL = 1, CR = 1, KR = 1, and apply a factor of safety. Use SF = 2 and SH =
Want to see the full answer?
Check out a sample textbook solutionChapter 15 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
- A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic loaarrow_forwardA double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. b) Find tangential force on worm.arrow_forwardPlease answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0arrow_forward
- The parallel shafts are connected with two full depth spur gears, with a pinion module of 4 mm. The pressure angle is 25 degree. The number of teeth of the gear is 52. The angular speed ratio is desired as 2,6. Calculate the pitch line velocity (m/s) where the angular speed of the pinion is 2600 rev/min.arrow_forwardA pinion and gear with module 5 mm has a speed reduction ratio of 6 : 1. If centre distance is 420 mm, number of teeth on the pinion is _________ .arrow_forwardColegio de Muntinlupa fabricated a pair of spur gear 2.5 module (20° full depth involute tooth) and to be mounted on shafts with a centerline distance of 90 mm. The speed ratio required is 3:1. Determine the following: a. Pitch diameter of pinionb. Pitch diameter of gearc. Number of teeth of piniond. Number of teeth of geare. Circular pitch of pinionf. Circular pitch of gearg. Addendumh. Dedendumi. Clearancej. Whole depthk. Working Depthl. Backlashm. Tooth thicknessn. Tooth space widtho. Outside diameter of pinionp. Outside diameter of gearq. Root diameter of pinionr. Root diameter of gears. Base diameter of piniont. Base diameter of geararrow_forward
- a parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. the helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and normal diameter pitch of 10 teeth/inch. If the pinion is rotating at 1800 rpm and transmits 50 Hp. find the normal Forcearrow_forwardA straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear will be rotating at a speed of 480 rpm. If the module of the pinion is 2,5 mm and pressure angle is 25 degree; Calculate the module (mm) of the gear.arrow_forwardA 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear. Part A Find the appropriate standard diametral pitch for the gearset. Part B Find the minimum required face width of the gears needed to satisfy the safety requirementsarrow_forward
- A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. If the center distance is increased by 0.125 in., what are the new values for the contact ratio and the pressure angle?arrow_forwardA gear set with a 20-tooth input pinion and a 42-tooth gear has a diametral pitch of 4 teeth/in. the pinion speed is 200 rpm with an input torque of 170 in-lbf. Which component of the load contributes to the transmitted power and what is it’s magnitude? Choose answer below Radial load 68lbf Tangential load 68lbf Radial load 136 lbf Tangential load 136 lbf None of the abovearrow_forwardA simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratioarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY