SHIGLEY'S MECH.ENGINEERING DESIGN-EBK>I
10th Edition
ISBN: 9781259489563
Author: BUDYNAS
Publisher: INTER MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 15, Problem 6P
To determine
The power rating for gear-set based bending strength.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear.
Part A
Find the appropriate standard diametral pitch for the gearset.
Part B
Find the minimum required face width of the gears needed to satisfy the safety requirements
A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut.
A.Determine the diametral pitch,
B. face width,
C. and tooth numbers if the material is cast iron, class 25
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45.
A. Determine the diametral pitch,
B. face width,
C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
Chapter 15 Solutions
SHIGLEY'S MECH.ENGINEERING DESIGN-EBK>I
Ch. 15 - An uncrowned straight-bevel pinion has 20 teeth, a...Ch. 15 - For the gearset and conditions of Prob. 15-1, find...Ch. 15 - An uncrowned straight-bevel pinion has 30 teeth, a...Ch. 15 - For the gearset and conditions of Prob. 15-3, find...Ch. 15 - An uncrowned straight-bevel pinion has 22 teeth, a...Ch. 15 - Prob. 6PCh. 15 - In straight-bevel gearing, there are some analogs...Ch. 15 - Refer to your solution to Probs. 15-1 and 15-2. If...Ch. 15 - Prob. 9PCh. 15 - Prob. 10P
Ch. 15 - Apply the relations of Prob. 15-7 to Ex. 15-1 and...Ch. 15 - Prob. 14PCh. 15 - 15-15 to 15-22 As in Ex. 15-4, design a...Ch. 15 - 15-15 to 1 5-22 As in Ex. 154, design a...Ch. 15 - 15-15 to 15-22 As in Ex. 15-4, design a...Ch. 15 - 15-15 to 15-22 As in Ex. 15-4, design a...Ch. 15 - 15-15 to 15-22 As in Ex. 15-4, design a...Ch. 15 - 15-15 to 15-22 As in Ex. 15-4, design a...Ch. 15 - 15-15 to 15-22 As in Ex. 15-4, design a...Ch. 15 - Prob. 22P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q/A steel spur pinion and gear of grade 1 have a diametral pitch of 11 teeth/in , shaped profile teeth, 16 and 32 teeth, respectively, a 20. pressure angle, the pinion speed is 585 rev/min. The tooth properties are Sactual bending =20230 psi and the Brinell hardness is 210. For a design factor of 3, a face width of 0.85 in, what is the power due to bending and wear for pinion? Hint: - use "Shigleys Mechanical Engineering Design 8th Edition"arrow_forwardA Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.arrow_forwardFind the gear ratio, circular pitch, base pitch, pitch diameters, pitch radii, center distance, addendum, dedendum, whole depth, clearance of a gearset with the given parameters. A diametral pitch is 6 teeth per inch, 20°-pressure-angle, 19-tooth pinion and a 37-tooth gear. Assumptions: The tooth forms are standard AGMA full-depth involute profiles.arrow_forward
- A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic loadarrow_forwardA pair of 20 pressure angle bevel gears of N , = 30 and N2 = 60 has a module m of 8.5 mm at the outside diameter . Determine the power capacity of the pair , using the Lewis and Buckingham equations . The gears have face width of 70 mm , K , = 1.5 , and the pinion rotates at 720 rpm . The gears are made of steel SAE 1040 and hardened to about 200 Bhn Hi sir this design machinearrow_forwardPlease answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0arrow_forward
- 13-32 The 247 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 1000 rev/min and is driven at a power of 25 hp. Gears 4, 5, and 6 have 24, 36, and 144 teeth, respectively. What torque can arm 3 deliver to its output shaft? Draw free-body diagrams of the arm and of each gear and show all forces that act upon them.arrow_forwardA parallel-shaft gearset consists of an 18-tooth helical pinion driving a 32-tooth gear. The pinion has a left-hand helix angle of 20, a normal pressure angle of 25, and a normal module of 3 mm. Evaluate root diameter (mm) of the pinion. A) 51,21 B) 49,92 C) 50,00 D) 48,00 E) 52,08arrow_forwardThe figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.arrow_forward
- Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4arrow_forwardA helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.arrow_forwardProvide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License