Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 16, Problem 16.13PP
A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Nozzle of diameter 20 mm is fitted to a pipe of diameter 10 min find the force exerted on the water which is flowing through the pipe at the rating 1.2 m/min..
Water at a pressure of 300 kN/m flows through a horizontal pipe of 120 mm diameter with a velocity of 3 m/s. If the diameter of the pipe gradually reduces to 65 mm, what is the axial force on the pipe assuming no loss of energy.
For the system shown below, calculate the vertical distance (in meters) between the surfaces of the two reservoirs when water at 10°C flows from A to B at the rate of 0.03 m3/s. The elbows are standard. The inlet is inward projecting, and the exit is square edged. The total length of the 4-in pipe is 94 m. For the 6-in pipe it is 274 m.
Chapter 16 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 16 - Calculate the force required to hold a flat plate...Ch. 16 - What must be the velocity of flow of water from a...Ch. 16 - Calculate the force exerted on a stationary curved...Ch. 16 - A highway sign is being designed to withstand...Ch. 16 - Compute the forces in the vertical and horizontal...Ch. 16 - Figure 16.13 O shows a free stream of water at 180...Ch. 16 - Compute the horizontal and vertical forces exerted...Ch. 16 - In a plant where hemispherical cup-shaped parts...Ch. 16 - A stream of non-flammable oil (sg 5 0.90) is...Ch. 16 - A 2 -in-diameter stream of water having a velocity...
Ch. 16 - Figure 16.17 O represents a type of flowmeter in...Ch. 16 - Water is piped vertically from below a boat and...Ch. 16 - A 2 -in nozzle is attached to a hose with an...Ch. 16 - Seawater (sg 5 1.03) enters a heat exchanger...Ch. 16 - A reducer connects a standard 6 -in Schedule...Ch. 16 - Calculate the force on a elbow attached to an in...Ch. 16 - Calculate the force required to hold a 90 elbow in...Ch. 16 - Calculate the force required to hold a 180 close...Ch. 16 - A bend in a tube causes the flow to turn through...Ch. 16 - A vehicle is to be propelled by a jet of water...Ch. 16 - A part of an inspection system in a packaging...Ch. 16 - Shown in Fig. 16.20 is a small decorative wheel...Ch. 16 - For the wheel described in Problem 16.22. compute...Ch. 16 - A set of louvers deflects a stream of warm air...Ch. 16 - Prob. 16.25PPCh. 16 - Prob. 16.26PPCh. 16 - Figure 16.22 shows a device for clearing debris...Ch. 16 - Prob. 16.28PPCh. 16 - Figure 16.23 is a sketch of a turbine in which the...Ch. 16 - Repeat Problem 16.29 with the blade rotating as a...Ch. 16 - Repeat Problem 16.29, except with the blade...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A jet of water with a diameter of 100 mm flows vertically until it meets a solid vane that deflected it at an angle of 180°. The initial velocity of the jet is 20 m/s. As a result of friction, the velocity of the jet leaving the vane is 15 m/s. Assuming the fluid is at atmospheric pressure throughout and neglecting the gravity effects, calculate the magnitude of the force exerted by the water on the vane. (water density 1000 kg/m3)arrow_forwardThe drawing shows a centrifugal fan. The fan draws 25 m^3/s of air from the room through the 0.75 diameter bellmouth inlet. The air is discharged into a 0.5 m diameter pipe which is connected to the downstream piping by a flexible connector. Note that the flexible connector does not transmit any forces or momentum between the connected components. Determine the forces in the x and y directions which the floor must apply to hold the fan in place. Assume incompressible flow with p=1.3 kg/m^3. Atmospheric pressure is 101 kPa.arrow_forwardA fire pump delivers water through a 150 mm main to a hydrant to which is connected a 75 mm hose, terminating in a 25 mm nozzle. The nozzle is 3 m above the hydrant and 18 m above the pump. Assuming a total frictional loss of 18.5 m from the pump to the base of the nozzle, and a loss in the nozzle of 10 per cent of the velocity head in the jet, and neglecting air resistance, what gage pressure at the pump is necessary to throw a stream 30 m vertically above the nozzle?arrow_forward
- A jet of water of diameter 50 mm, having a velocity of 30 m/s strikes a curved vane which is moving with a velocity of 15 m/s. The jet makes an angle of 30º with the direction of motion of vane at inlet and leaves at an angle of 120º to the direction of motion of vane at outlet, calculate a) Vane angles, if water enters and leaves the vane without shock b) work done per second per unit weight of water striking the vanes per seconarrow_forwardThe volume flow rate of water that recirculates from the blade outlet to the impeller is estimated to be 0.4524 ft^3/min, and the losses through the shaft sealing is negligible. The hydraulic and mechanical efficiency of a centrifugal pump are 95% and 93%, respectively. If the pump delivers water a flow rate of 12 ft^3/min, calculate the pump efficiency in %.arrow_forwardA Huston turbine impeller with a diameter of 0.217 m is used in a tank with a diameter of 0.65 m filled with liquid to a height of 0.65 m. Four baffles (baffles) are used to avoid vortex, all with a width of 0.01 m. The turbine operates at 275 rpm with a liquid that has a density of 1000 kg/m³ and a viscosity of 0.020Pa.s. a) Considering that the mechanical efficiency is 50%, what is the power in HP of the commercial engine that you should specify?arrow_forward
- Water flows from a large tank through an orifice of 75 mm diameter and against a block as shown in the figure. The water jet strikes the block at the vena contrata. The block weighs 223 N and the coefficient of friction between the block and the floor is 0.57. The coefficient of discharge C = 0.60 and its coefficient of contraction Cc = 0.62. What is the minimum height to which water must rise in the tank in order to start the block moving to the right?arrow_forwardInclude a free body diagram. A 100-mm-diameter jet of water is discharged (horizontally) from a nozzle into the air. The flow rate of the water jet is 0.22 m3/s. Determine the power in the jet. Assume the jet of water is at the datum.arrow_forwardOil with a specific weight of 53 lb/ft3 is exiting from a pipe whose center line is 17 ft below the surface of the oil. What is the velocity of the oil from the pipe if there is 1.5 ft head loss in the exit pipe?arrow_forward
- A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The lost head in the nozzle is 20% of the velocity head in the jet. If the pressure at the base of the nozzle is 725 KPa: compute the discharge in m3/min; the maximum horizontal range to which the stream can be thrown; the maximum vertical reach, and the diameter of the jet mid-height. Neglect air resistance.arrow_forwardTwo circular water jets (d = 0.5 in.) issue steadily from this unusual nozzle. If Vj = 80.2 ft/s, what force is required at the flange to hold the nozzle in place in the x-direction. The pressure in the 4 in. pipe (D = 3.5 in) is 50 psig.arrow_forwardWater is flowing out of the nozzle (2) into atmospheric pressure (101 kPa). What is the gauge pressure at point (1), when flow rate is 32.18 m3/h and frictional losses are ignored? Water density is 1000 kg/m3.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License