Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 16, Problem 21P
A two-jaw clutch has the dimensions shown in the figure and is made of ductile steel. The clutch has been designed to transmit 2 kW at 500 rev/min. Find the bearing and shear stresses in the key and the jaws.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A wagon weighing 5100 Kg moving at a speed of 8 km/h has to be brought to rest. Springs made of wire diameter 25mm with a Dm of 250mm and with 24 turns are available. Find the number of springs required in buffer to stop the wagon at a compression of 180mm.
b)A close coiled helical spring is made of diameter wire 25mm. The spring index is 8. Findthe number of turns required and maximum allowable load if the allowable shear stress is100 MPa and elongation is limited to 40mm. [G=80 GPa
The two square-jaw grips have the dimensions shown in the figure and are made of mild steel. The clutch is designed to transmit a power of 1.8 kW at 600 rpm. Calculate the surface pressure and shear stresses on the wedges and jaws. they all in mm
A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces has worn away by 1.25 mm. find the maximum power that can be transmitted assuming uniform wear. A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces…
Chapter 16 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 16 - The figure shows an internal rim-type brake having...Ch. 16 - For the brake in Prob. 16-1, consider the pin and...Ch. 16 - In the Figure for Prob. 16-1, the inside rim...Ch. 16 - The figure shows a 400-mm-diameter brake drum with...Ch. 16 - The block-type hand brake shown in the figure has...Ch. 16 - Suppose the standard deviation of the coefficient...Ch. 16 - The brake shown in the figure has a coefficient of...Ch. 16 - Prob. 8PCh. 16 - Prob. 9PCh. 16 - Prob. 10P
Ch. 16 - The maximum band interface pressure on the brake...Ch. 16 - The drum for the band brake in Prob. 1611 is 12 in...Ch. 16 - The brake shown in the figure has a coefficient of...Ch. 16 - The figure depicts a band brake whose drum rotates...Ch. 16 - The figure shows a band brake designed to prevent...Ch. 16 - A plate clutch has a single pair of mating...Ch. 16 - A hydraulically operated multidisk plate clutch...Ch. 16 - Prob. 18PCh. 16 - A cone clutch has D = 12 in, d = 11 in, a cone...Ch. 16 - Prob. 20PCh. 16 - A two-jaw clutch has the dimensions shown in the...Ch. 16 - Prob. 22PCh. 16 - Prob. 23PCh. 16 - Prob. 24PCh. 16 - Using the data of Table 16-6, find the mean output...Ch. 16 - When a motor armature inertia, a pinion inertia,...Ch. 16 - For the conditions of Prob. 1627, make a plot of...Ch. 16 - Prob. 29PCh. 16 - Prob. 30PCh. 16 - Prob. 31P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The solid steel rotating shaft in the figure is supported at B and C, and is driven by a gear, not seen, which is linked to spur gear D which has a pitch diameter of 150 mm. The drive gear force F acts at a pressure angle of 20 degrees. The shaft transmits a torque to point A of Ta-350 N.m. The properties of machined steel shaft are Sy-420 MPa and Sut-560MPa. Use a safety factor of 2.5 and determine the minimum allowable diameter in section B and C. Assume sharp felt radii at the bearing shoulders to estimate the stress concentration factors.Explain.arrow_forwardDesign a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solutionarrow_forwardQ 3. The brake shown in the figure uses a band that has a coefficient of friction equivalent to rigid molded asbestos (dry) and is to operate using a maximum force F of 400 N. If the band width is 50 mm, find the band tensions and the braking torque.arrow_forward
- 8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.arrow_forward5. Design a sleeve coupling for the transmission of 12 kW at 300 rpm by two connected steel shafts. Take service factor KS 1.25. The sleeve is made of CI. The key and the shaft are made of the same material. Allowable stress: Shear stresses in key and shaft 50 MPa Crushing stress in key= 100 MPa Shear stress in CI sleeve = 10 MPaarrow_forwardA solid and a hollow shaft, connected by a coupling, transmit power. The outside diameters of the shafts are the same and the inside diameter of the hollow shaft is 75 % of its outside diameter. The solid shaft is three times as long as the hollow shaft. Take the modulus of rigidity for both shafts as 80 GPa. (a) If the angle of twist for the solid shaft is 1°, find the angle of twist for the hollow shaft. (b) If the maximum shear stress in the solid shaft is 30 MPa, find the maximum stress in the hollow shaft.arrow_forward
- A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPaarrow_forwardThe input shaft to a gearbox, shown in Figure 3, operates at a speed of n1 and transmits a power of 30 hp. The output power is 27 hp at a speed of n2. (a) What is the torque of each shaft (in kip · in.) and (b) the efficiency of the gearbox? Use n1 = 1800 rpm, n2 = 425 rpm. (c) Also compute for the torsional stress on the 1.5” diameter solid shaft C, and on the hollow shaft at E whose D =2” and d = 1.5”.arrow_forwardA pulley 610 mm diameter is driven at 300 revs/min by a belt, the tensions in the tight and slack sides of the belt being 670 N and 270 N. Find the power transmitted.arrow_forward
- Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80MPa while transmitting 45 kW at 900 rpm. Find the shaft if it is to be used for the input - output belts being on the same or opposite sides.arrow_forwardDesign a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solutionarrow_forwardA cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Everything About COMBINED LOADING in 10 Minutes! Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=N-PlI900hSg;License: Standard youtube license