MINDTAP WELDING FOR JEFFUS' WELDING: PR
8th Edition
ISBN: 9781305494749
Author: Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 17, Problem 12R
Using Table 17-3, Table 17-5, and Table 17-6, list the filler metals for the following metals.
a. 1020 low carbon steel
b. 309 stainless steel
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
the parts
Answer the following
elating to the drawing in figure (3a):
1- What is the name of the component?
2- What size is the oil hole? How far is the oil hole from the edge of the
cylinder?
3- How many holes have to be drilled $12?
4- What is the overall height of the finished item?
5- What welding is specified by the symbol marked A?
6- How many pieces are used to make this item?
7- What sizes of welds are used? How thick is item 2?
8- What are the general tolerances? How many surfaces are machine finished?
63 all hole -4 holes 012
BO
3²8
44.00
5 ROUND BAR
MINOR WEDS
Section A-A
6
PARTS LIST
425x6
MS
70xBx56
MS
3 ROUND BAR
BEOXDO
MS
2 MAIN WEB
200xBx35 MS
1 BASE PLATE
200x400x120 MS
ITEM
DESCRIPTION
SIZE
MATL
AND ENGINEERING
DRAMA
FRACED
CHECKED
TAFE:
K BERYCES CONSORTIA
TITLE
SHAFT SUPPORT BEARING
SCALE
12
02-MF 1- MY 98
F
TYP
140
200
←
All welde et unicee indicated otherwise
First
CHANGE
AMENDMENTS
NOTE:
70/98
ISSUE DATE
-A
LZ DO
ECH BY CKD
825
UN ES NOTED OTHERANSE
TOLERANCES…
How to answer Number 3 of the problem? Thank you
Name
Part 11
1. What does the following welding symbol indicate?
100
(5)
c-d
GTAW
4. Describe the following weld(s).
ASW
2. Describe the weld(s) indicated by the following welding symbol.
d
3. Sketch in the weld(s) indicated by the welding symbol.
b-c
GMAW
000000
w
a.
C.
d.
e.
b.
b.
C.
d.
e
C.
d
a.
b.
e.
5. Sketch the welding symbol describing the following spot weld(s).
375
18 Spot, Seam, and Projection Welds 255
0.31
Copyright Goodheart-Wilcox Co., Inc. May not be reproduced or posted to a publicly accessible website
Chapter 17 Solutions
MINDTAP WELDING FOR JEFFUS' WELDING: PR
Ch. 17 - What effect does torch angle have on the shielding...Ch. 17 - Why must the end of the filler rod be kept in the...Ch. 17 - What can cause tungsten contamination?Ch. 17 - What determines the correct current setting for a...Ch. 17 - What is the lowest acceptable amperage setting for...Ch. 17 - List the factors that affect the gas flow setting...Ch. 17 - When should the minimum gas flow rates be...Ch. 17 - What is the minimum gas flow rate for a nozzle...Ch. 17 - What is the maximum gas flow rate for a nozzle...Ch. 17 - Which incorrect welding parameters does stainless...
Ch. 17 - Using Table 17-4, determine the approximate...Ch. 17 - Using Table 17-3, Table 17-5, and Table 17-6, list...Ch. 17 - Why is it possible to control a large aluminum...Ch. 17 - What may happen to the end of the aluminum welding...Ch. 17 - What should be done if someone comes in contact...Ch. 17 - Using Table 17-7, determine the suggested setting...Ch. 17 - What can be done to limit oxide formation on...Ch. 17 - How should the filler metal be added to the molten...Ch. 17 - How can the rod be freed if it sticks to the...Ch. 17 - How is an outside corner joint assembled?Ch. 17 - What must be done with the weld craters when back...Ch. 17 - What can prevent both sides of a stainless steel...Ch. 17 - How is the filler metal added for a 3F weld?Ch. 17 - What can cause undercutting on a 3F tee joint?Ch. 17 - What helps hold the weld in place on a 2F lap...Ch. 17 - What helps hold the weld in place on a 4G weld?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Referring to Table 28-5, what stainless steel filler metal would be selected for welding a. 304L stainless steel to 314 stainless steel? b. 321 stainless steel to 348 stainless steel? c. 316 stainless to mild steel?arrow_forwardWhat are the F-number and A-numbers for the stainless filler metal used in Practice 19-8?arrow_forwardAccording to Table 15-4, what is the range of volts and amps for E70T-11 0.035 diameter filler wire?arrow_forward
- 6/ Which one of the following statement is correct? Graphite is used as the mold material for producing the aluminium parts. The liquid metal is poured through the riser for smooth running of the liquid metal in to the mold. The liquid metal is poured through the runner for smooth running of the liquid metal in to the mold. The liquid metal is poured through the core for smooth running of the liquid metal in to the mold.arrow_forwardUsing Table 16-3, determine the gas post flow time for a 3/32-in. (2.4-mm) tungsten.arrow_forwardWhich of the following aluminium alloys will be stronger? A. 2024-T10 B. 2024 C. 2024-T6 D. 2024-H18arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Introduction to Ferrous and Non-Ferrous Metals.; Author: Vincent Ryan;https://www.youtube.com/watch?v=zwnblxXyERE;License: Standard Youtube License