Manufacturing Engineering And Technology
7th Edition
ISBN: 9789810694067
Author: Stephen R. Schmid (author) Serope Kalpakjian (author)
Publisher: Pearson Education Orphans
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 17, Problem 33QTP
Estimate the maximum tonnage required to compact a brass slug 3.0 in. in diameter. Would the height of the slug make any difference in your answer? Explain your reasoning.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In powder processing, a cylinder with a diameter of 2 inches and a height of 10 inches is to be made from fine copper powders. A single-action press is used for compaction. If the average density of the green product is 7 g/cm3 at the bottom half of the cylinder, estimate the compaction pressure at the punch surface. Assume no friction between the powders. The coefficient of friction between particles and containers is 0.2.
Briefly explain the Casting and Molding processes and define their basic requirements.
If a manufacturer was asked to produce a set of plastic bottles, which method would you suggest?Justify your answer.
What kind of system is compression molding machine? open, closed, or isolated? Explain.
Chapter 17 Solutions
Manufacturing Engineering And Technology
Ch. 17 - Describe briefly the production steps involved in...Ch. 17 - Name the various methods of powder production and...Ch. 17 - Explain why metal powders may be blended.Ch. 17 - Describe the methods used in metal powder...Ch. 17 - What is isostatic pressing? How is it different...Ch. 17 - What hazards are involved in PM processing?...Ch. 17 - Describe what occurs to metal powders during...Ch. 17 - Prob. 8RQCh. 17 - Why might secondary and finishing operations be...Ch. 17 - Prob. 10RQ
Ch. 17 - Prob. 11RQCh. 17 - Prob. 12RQCh. 17 - Prob. 13RQCh. 17 - What is screening of metal powders? Why is it...Ch. 17 - Why are protective atmospheres necessary in...Ch. 17 - Why is there density variation in the compacting...Ch. 17 - What is the magnitude of the stresses and forces...Ch. 17 - List the similarities and differences of forging...Ch. 17 - Give some reasons that powder-injection molding is...Ch. 17 - How does the equipment used for powder compaction...Ch. 17 - Explain why the mechanical and physical properties...Ch. 17 - What are the effects of the different shapes and...Ch. 17 - Describe the relative advantages and limitations...Ch. 17 - How different, if any, are the requirements for...Ch. 17 - The powder metallurgy process can be competitive...Ch. 17 - What are the reasons for the shapes of the shown...Ch. 17 - Should green compacts be brought up to the...Ch. 17 - Because they undergo special processing, metal...Ch. 17 - In Fig. 17.12, it can be seen that the pressure is...Ch. 17 - Why do the compacting pressure and the sintering...Ch. 17 - What will be stronger: a blend of stainless steel...Ch. 17 - Name the various methods of powder production and...Ch. 17 - Estimate the maximum tonnage required to compact a...Ch. 17 - Refer to Fig. 17.11a. What should be the volume of...Ch. 17 - Determine the shape factors for (a) a cylinder...Ch. 17 - Estimate the number of particles in a 500-g sample...Ch. 17 - Prob. 37QTPCh. 17 - A coarse copper powder is compacted in a...Ch. 17 - A gear is to be manufactured from iron powders. It...Ch. 17 - What volume of powder is needed to make the gear...Ch. 17 - The axisymmetric part shown in Fig. P17.41 is to...Ch. 17 - Prepare an illustration similar to Fig. 13.1,...Ch. 17 - Prob. 44SDPCh. 17 - Compare the design considerations for PM products...Ch. 17 - Prob. 46SDPCh. 17 - Prob. 47SDPCh. 17 - Using the Internet, locate suppliers of metal...Ch. 17 - Explain why powder metal parts are commonly used...Ch. 17 - Prob. 50SDPCh. 17 - Describe how the information given in Fig. 17.15...Ch. 17 - It was stated that, in the process shown in Fig....Ch. 17 - Prob. 53SDPCh. 17 - The axisymmetric parts shown in Fig. P17.54 are to...Ch. 17 - Assume you are working in technical sales. What...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Should green compacts be brought up to the sintering temperature slowly or rapidly? Explain your reasoning.arrow_forwardWhich law of thermodynamics best apply to compression molding machine? Explain why.arrow_forwardCompare compression and injection molding for speed, cost per part, investment cost, and flexibility in types of material that can be handled?arrow_forward
- Explain what you know about crystallographic anisotropy, which has an important place in sheet metal forming operations, with the help of shapes and formulations.arrow_forwardCeramics are much stronger in compression rather than indentation explain why?arrow_forwardMoulds for blow moulding can be made using aluminium whereas moulds for injection moulding are usuallymade out of tool steel, why?arrow_forward
- What were the main needs to develop colloidal technique for powder processing, explain your arguments clearly?arrow_forwardWhat is the difference between caulking and fullering? Explain with the help of neat sketches.arrow_forwardFor a sand casting a steel rectangular plate with dimensions 80mm x 120mm x 20mm. Calculate shrinkage and draft allowance. And draw the designed pattern. Assume shrinkage of material as 0.1% for 12 inch, pattern material is wood and assume suitable draft anglesarrow_forward
- EXPLAIN WHAT IS PROTOTYPE BY FIGURE AND WHY IS IMPORTANT ? EXPLAIN WHICH FACTORS TO BE CONSIDERED OF SIZING THE DESIGN PARTS ? EXPLAIN WHICH FACTORS TO BE CONSIDERED IN MATERIALS SELECTION BY FIGURES ?arrow_forwardDiscuss the effect of monomodal and bimodal particle size distribution of powderson the microstructure and properties of advanced ceramics. Which starting powders would youprefer and WHY?arrow_forwardA polymer straight propeller with a diameter = 15in(measured diameter = 382mm) and pitch = 5.6in(142.24mm). A drawing is given below for the propeller. Explain the diameter of the propeller, pitch of the propellerand the drawing given.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dimensional Analysis - in physics; Author: Jennifer Cash;https://www.youtube.com/watch?v=c_ZUnEUlTbM;License: Standard youtube license