Engineering Mechanics: Statics & Dynamics (14th Edition)
14th Edition
ISBN: 9780133915426
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 17.4, Problem 73P
Cable is unwound from a spool supported on small rollers at A and B by exerting a force T= 300 N on the cable. Compute the time needed to unravel 5 m of cable from the spool if the spool and cable have a total mass of 600 kg and a radius of gyration of kO = 1.2 m. For the calculation, neglect the mass of the cable being unwound and the mass of the rollers at A and B. The rollers turn with no friction.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The force F 250 N is applied to a wheel weighing 20 kg and having a radius of inertia of 150 mm as shown in the figure. This force lifts a weight B of 10 kg. Calculate the angular acceleration of the pulley and the normal acceleration of the weight B, the tension of the rope and the reaction in the bearing of the pulley.
The spool has mass, m, and a radius of gyration kG. An inextensible cord is attached to the wall at A. The cord is wound around the radius R and the outer radius 2R. The coefficient of friction between the spool and the ground is mu.
What it the critical force, Fcrit (force required to cause motion) applied at point B?
If force= 2Fcrit what is the linear acceleration of the center of mass?
If force= 2Fcrit what is the tension in cord AC?
The force F of 250 N is applied because a block with a mass of 20 kg and a radius of inertia of 160 mm as shown in the figure. This force lifts the weight B of 10 kg. Calculate the pulley angular acceleration and the normal acceleration of weight B, tension in the cable and reaction in the pulley bearing.
Chapter 17 Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
Ch. 17.1 - Determine the moment of inertia Iy for the slender...Ch. 17.1 - The solid cylinder has an outer radius R1 height...Ch. 17.1 - Determine the moment of inertia of the thin ring...Ch. 17.1 - The paraboloid is formed by revolving the shaded...Ch. 17.1 - Determine the radius of gyration kr of the body....Ch. 17.1 - The sphere is formed by revolving the shaded area...Ch. 17.1 - The frustum is formed by rotating the shaded area...Ch. 17.1 - Prob. 8PCh. 17.1 - Prob. 9PCh. 17.1 - The pendulum consists of a 4-kg circular plate and...
Ch. 17.1 - The assembly is made of the slender rods that have...Ch. 17.1 - Prob. 12PCh. 17.1 - The wheel consists of a thin ring having a mass of...Ch. 17.1 - If the large ring, small ring and each of the...Ch. 17.1 - Determine the moment of inertia about an axis...Ch. 17.1 - Prob. 16PCh. 17.1 - Determine the location y of the center of mass G...Ch. 17.1 - Prob. 18PCh. 17.1 - Prob. 19PCh. 17.1 - Determine the moment of inertia of the wheel about...Ch. 17.1 - The pendulum consists of the 3-kg slender rod and...Ch. 17.1 - Prob. 22PCh. 17.1 - Determine the moment of inertia of the overhung...Ch. 17.3 - Draw the free-body and kinetic diagrams of the...Ch. 17.3 - Prob. 2PPCh. 17.3 - Prob. 1FPCh. 17.3 - Prob. 2FPCh. 17.3 - Prob. 3FPCh. 17.3 - Prob. 4FPCh. 17.3 - At the instant shown both rods of negligible mass...Ch. 17.3 - Prob. 6FPCh. 17.3 - The door has a weight of 200 lb and a center of...Ch. 17.3 - The door has a weight or 200 lb and a center of...Ch. 17.3 - The jet aircraft has a total mass of 22 Mg and a...Ch. 17.3 - The sports car has a weight of 4500 lb and center...Ch. 17.3 - The assembly has a mass of 8 Mg and is hoisted...Ch. 17.3 - The assembly has a mass of 4 Mg and is hoisted...Ch. 17.3 - The uniform girder AB has a mass of 8 Mg....Ch. 17.3 - A car having a weight of 4000 lb begins to skid...Ch. 17.3 - A force of P = 300 N is applied to the 60-kg cart....Ch. 17.3 - Determine the largest force P that can be applied...Ch. 17.3 - The trailer with its load has a mass of 150-kg and...Ch. 17.3 - The desk has a weight of 75 lb and a center of...Ch. 17.3 - The desk has a weight of 75 lb and a center of...Ch. 17.3 - The 150-kg uniform crate rests on the 10-kg cart....Ch. 17.3 - The 150-kg uniform crate rests on the 10-kg cart....Ch. 17.3 - The bar has a weight per length w and is supported...Ch. 17.3 - The smooth 180-lb pipe has a length of 20 ft and a...Ch. 17.3 - The smooth 180-lb pipe has a length of 20 ft and a...Ch. 17.3 - The uniform crate has a mass of 50 kg and rests on...Ch. 17.3 - Determine the acceleration of the 150-lb cabinet...Ch. 17.3 - Prob. 44PCh. 17.3 - Prob. 45PCh. 17.3 - Prob. 46PCh. 17.3 - Prob. 47PCh. 17.3 - The snowmobile has a weight of 250 lb, centered at...Ch. 17.3 - If the carts mass is 30 kg and it is subjected to...Ch. 17.3 - Prob. 50PCh. 17.3 - The pipe has a mass of 800 kg and is being towed...Ch. 17.3 - The pipe has a mass of 800 kg and is being towed...Ch. 17.3 - Prob. 53PCh. 17.3 - Prob. 54PCh. 17.3 - Prob. 55PCh. 17.3 - Prob. 56PCh. 17.4 - The 100-kg wheel has a radius of gyration about...Ch. 17.4 - Prob. 8FPCh. 17.4 - Prob. 9FPCh. 17.4 - Prob. 10FPCh. 17.4 - Prob. 11FPCh. 17.4 - Prob. 12FPCh. 17.4 - The 10-kg wheel has a radius of gyration kA = 200...Ch. 17.4 - The uniform 24-kg plate is released from rest at...Ch. 17.4 - The uniform slender rod has a mass m. If it is...Ch. 17.4 - The tent rod has a mass of 2 kg/m. If it is...Ch. 17.4 - If a horizontal force of P = 100 N is applied to...Ch. 17.4 - The 10-lb bar is pinned at its center O and...Ch. 17.4 - The 10-lb bar is pinned at its center O and...Ch. 17.4 - A cord is wrapped around the outer surface of the...Ch. 17.4 - Disk A has a weight of 5 lb and disk B has a...Ch. 17.4 - Prob. 66PCh. 17.4 - If the cord at B suddenly fails, determine the...Ch. 17.4 - Prob. 68PCh. 17.4 - The 20-kg roll of paper has a radius of gyration...Ch. 17.4 - The 20-kg roll of paper has a radius of gyration...Ch. 17.4 - The reel of cable has a mass of 400 kg and a...Ch. 17.4 - Prob. 72PCh. 17.4 - Cable is unwound from a spool supported on small...Ch. 17.4 - The 5-kg cylinder is initially at rest when it is...Ch. 17.4 - Prob. 75PCh. 17.4 - Prob. 76PCh. 17.4 - Disk D turns with a constant clockwise angular...Ch. 17.4 - Prob. 78PCh. 17.4 - Prob. 79PCh. 17.4 - Prob. 80PCh. 17.4 - Prob. 81PCh. 17.4 - Prob. 82PCh. 17.4 - Prob. 83PCh. 17.4 - Prob. 84PCh. 17.4 - Prob. 85PCh. 17.4 - Prob. 86PCh. 17.4 - Prob. 87PCh. 17.4 - The 100-kg pendulum has a center of mass at G and...Ch. 17.5 - The Catherine wheel is a firework that consists of...Ch. 17.5 - The uniform 60-kg slender bar is initially at rest...Ch. 17.5 - Prob. 14FPCh. 17.5 - Prob. 15FPCh. 17.5 - The 20- kg sphere rolls down the inclined plane...Ch. 17.5 - The 200-kg spool has a radius of gyration about...Ch. 17.5 - The 12-kg slender rod is pinned to a small roller...Ch. 17.5 - If the disk in Fig. 17-19 rolls without slipping,...Ch. 17.5 - The 20-kg punching bag has a radius of gyration...Ch. 17.5 - The uniform 150-lb beam is initially at rest when...Ch. 17.5 - The tire has a weight of 30 lb and a radius of...Ch. 17.5 - The tire has a weight of 30 lb and a radius of...Ch. 17.5 - The spool has a mass of 100 kg and a radius of...Ch. 17.5 - Solve Prob.17-96 if the cord and force P = 50 N...Ch. 17.5 - The spool has a mass of 100 kg and a radius of...Ch. 17.5 - The 12-kg uniform bar is supported by a roller at...Ch. 17.5 - A force of F= 10 N is applied to the 10-kg ring as...Ch. 17.5 - If the coefficient of static friction at C is s =...Ch. 17.5 - The 25-lb slender rod has a length of 6 ft. Using...Ch. 17.5 - The 15-lb circular plate is suspended from a pin...Ch. 17.5 - If P = 30 lb, determine the angular acceleration...Ch. 17.5 - If the coefficient of static friction between the...Ch. 17.5 - The uniform bar of mass m and length L is balanced...Ch. 17.5 - Solve Prob.17-106 if the roller is removed and the...Ch. 17.5 - The semicircular disk having a mass of 10 leg is...Ch. 17.5 - The 500-kg concrete culvert has a mean radius of...Ch. 17.5 - The 15-lb disk rests on the 5-lb plate. A cord is...Ch. 17.5 - The semicircular disk having a mass of 10 kg is...Ch. 17.5 - The circular concrete culvert rols with an angular...Ch. 17.5 - The uniform disk of mass m is rotating with an...Ch. 17.5 - The uniform disk of mass m is rotating with an...Ch. 17.5 - A cord is wrapped around each of the two 10-kg...Ch. 17.5 - The disk of mass m and radius r rolls without...Ch. 17.5 - The uniform beam has a weight W. If it is...Ch. 17.5 - The 500-lb beam is supported at A and B when it is...Ch. 17.5 - The solid ball of radius rand mass m rolls without...Ch. 17.5 - By pressing down with the finger at B, a thin ring...Ch. 17.5 - Prob. 1RPCh. 17.5 - Prob. 2RPCh. 17.5 - Prob. 3RPCh. 17.5 - Prob. 4RPCh. 17.5 - Prob. 5RPCh. 17.5 - Prob. 6RPCh. 17.5 - Prob. 7RPCh. 17.5 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The pulley in Fig has radius R and a moment of inertia I. The rope does not slip over the pulley, and the pulley spins on a frictionless axle. The coefficient of kinetic friction between block A and the tabletop is mk . The system is released from rest, and block B descends. Block A has mass mA and block B has mass mB . Use energy methods to calculate the speed of block B as a function of the distance d that it has descended.arrow_forwardMotive power for the experimental 17.9-Mg bus comes from the energy stored in a rotating flywheel which it carries. The flywheel has a mass of 1380 kg and a radius of gyration of 560 mm and is brought up to a maximum speed of 3560 rev/min. If the bus starts from rest and acquires a speed of 60 km/h at the top of a hill 89 m above the starting position, compute the reduced speed N of the flywheel. Assume that 9 percent of the energy taken from the flywheel is lost. Neglect the rotational energy of the wheels of the bus. The 17.9-Mg mass includes the flywheel.arrow_forwardA 256-lb block is released from rest when the spring is unstretched. The drum has a weight of 76 lb and a radius of gyration of kO = 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k=78 lb/ft. The radius of the drum are: rin=0.485ft and rout=0.82ft. Find the velocity of the block after it has descended d=4 feet.arrow_forward
- Disk B weighs 322 lb and a massless hub with a radius of 2.00 ft is attached to it as shown. Block Cweighs 128.8 lb and has a downward velocity of 20.0 ft/s in the position shown. The spring is under a tension of 200 lb in the position shown. Calculate the force constant of the spring if block C has a speed of 10.00 ft/s downward after it has fallen 4.00 ft.arrow_forwardA Porter governor has equal arms each 250 mm long and pivoted on the axis of rotation. Each flyball has a mass of 10 kg and the mass of the central load on the sleeve is 50 kg. The radius of rotation of the flyball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Find the range of speed, when the friction at the sleeve is neglected. Select one: A. 35.4 rpm B. 25.4 rpm C. 15.4 rpm D. 45.4 rpmarrow_forwardThe thin rod of the figure has a mass of 15kg and is attached to a spring of constant K = 50 N/m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in horizontal position (ø = 0°) and only conservative forces act on it, determine: a) What is the moment of inertia of the thin rod around the axis of rotation in A? b) What is the angle at which the rod is momentarily resting again? c) What is the maximum angular speed of the route? Please attach the free body diagram if necessary. Thank you!arrow_forward
- A conical pendulum having a 2 kg massattached at the end of the string is rotating ata constant speed of 4.00 m/s around ahorizontal circle of radius 1.00 m. Calculate(a) the angle that the string makes with thevertical;(b) the tension in the string; and(c) the length of the string.arrow_forwardThe double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinningarrow_forwardThe mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear Bits mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction; a) The time elapsed until the angular velocity of gear B reaches 600 rpm.b) Find the tangential force from gear B to gear A.arrow_forward
- The thin rod in the figure has a mass of 15kg and is attached to a spring of constant k = 50 N / m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in a horizontal position (ѳ = 0 °) and only conservative forces act on it, determine:a) What is the moment of inertia of the thin rod around the axis of rotation at A? b) What is the angle at which the rod is momentarily at rest again? c) What is the maximum angular velocity of the path?arrow_forward1)Calculate the velocity of the arm, observed by a stationary person on the ground.2)Draw the FBD of the combined body (crane body, arm and load).3)Is the combined body stable? Why?4)Calculate the moment of the following, about wheel A,i) combined crane bodyii) load mass5)Which combined body’s component(s) will not fail? Why? (Hint: The crane was initially in equilibrium.)6)What are the various limits (maximum or minimum) for the combined body to be stable? Explain why.arrow_forwardThe mass of gear A is 25 kg and its centroidal radius of gyration is 105 mm. The mass of gear B is 13 kg and its centroidal radius of gyration is 85 mm. Calculate the angular acceleration of gear B when a torque of 16 N·m is applied to the shaft of gear A. Neglect friction. The angular acceleration is positive if counterclockwise, negative if clockwise..arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Introduction To Engg Mechanics - Newton's Laws of motion - Kinetics - Kinematics; Author: EzEd Channel;https://www.youtube.com/watch?v=ksmsp9OzAsI;License: Standard YouTube License, CC-BY