Physics for Scientists and Engineers With Modern Physics
9th Edition
ISBN: 9781133953982
Author: SERWAY, Raymond A./
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 19, Problem 14P
To determine
The increase in length.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Each year thousands of children are badly burned by hot tap water. The figure below shows a cross-sectional view of an antiscalding faucet attachment designed to prevent such accidents. Within the device, a spring made of material with a high coefficient of thermal expansion controls a movable plunger. When the water temperature rises above a preset safe value, the expansion of the spring causes the plunger to shut off the water flow. Assuming that the initial length L of the unstressed spring is 2.05 cm and its coefficient of linear expansion is 22 ✕ 10-6 (°C)-1, determine the increase in length of the spring when the water temperature rises by 35.0°C
A high-pressure gas cylinder contains 80.0 L of toxic gas at a pressure of 1.20 107 N/m2 and a temperature of 12.0°C. Its valve leaks after the cylinder is dropped. The cylinder is cooled to dry ice temperatures (−78.5°C), to reduce the leak rate and pressure so that it can be safely repaired. what is the final pressure in the tank, assuming a negligible amount of gas leaks while being cooled and that there is no phase change? What is the final pressure if one-tenth of the gas escapes? To what temperature must the tank be cooled to reduce the pressure to 1.00 atm (assuming the gas does not change phase and that there is no leakage during cooling)?
A cylinder with a cross-sectional area of 0.035 m2 is fitted with a piston that is free to move up and down. The piston has a weight of 14.0 N. The uninsulated cylinder is sitting in a water bath with a temperature of 16◦C. Inside the cylinder is a gas, occupying a volume of 3.6×10−4 cubic meters.
(a) What is the initial pressure inside the cylinder?
(b) The piston is locked in place and the cylinder is moved to a water bath with a temperature of 70 ◦C. What will be the volume of the gas? What will be the pressure in the gas when it reaches thermal equilibrium with the hot water bath? What kind of a change is this? Isothermal, isobaric, isovolumetric, or adiabatic?
(c) A weight of 15.5 N is placed on top of the piston and then the piston is unlocked so that it is free to move again. What will be the pressure in the gas when the piston is in equilibrium? What will be the volume of the gas when the pistion is in equilibrium? What kind of a change is this? Isothermal, isobaric,…
Chapter 19 Solutions
Physics for Scientists and Engineers With Modern Physics
Ch. 19.1 - Prob. 19.1QQCh. 19.3 - Consider the following pairs of materials. Which...Ch. 19.4 - If you are asked to make a very sensitive glass...Ch. 19.4 - Prob. 19.4QQCh. 19.5 - A common material for cushioning objects in...Ch. 19.5 - On a winter day, you turn on your furnace and the...Ch. 19 - Prob. 1OQCh. 19 - Prob. 2OQCh. 19 - Prob. 3OQCh. 19 - Prob. 4OQ
Ch. 19 - Prob. 5OQCh. 19 - Prob. 6OQCh. 19 - Prob. 7OQCh. 19 - Prob. 8OQCh. 19 - Prob. 9OQCh. 19 - Prob. 10OQCh. 19 - Prob. 11OQCh. 19 - Prob. 12OQCh. 19 - Prob. 13OQCh. 19 - Prob. 14OQCh. 19 - Prob. 1CQCh. 19 - Prob. 2CQCh. 19 - Prob. 3CQCh. 19 - Prob. 4CQCh. 19 - Prob. 5CQCh. 19 - Metal lids on glass jars can often be loosened by...Ch. 19 - Prob. 7CQCh. 19 - Prob. 8CQCh. 19 - Prob. 9CQCh. 19 - Prob. 10CQCh. 19 - Prob. 1PCh. 19 - Prob. 2PCh. 19 - Prob. 3PCh. 19 - Prob. 4PCh. 19 - Liquid nitrogen has a boiling point of 195.81C at...Ch. 19 - Prob. 6PCh. 19 - Prob. 7PCh. 19 - Prob. 8PCh. 19 - Prob. 9PCh. 19 - Prob. 10PCh. 19 - A copper telephone wire has essentially no sag...Ch. 19 - Prob. 12PCh. 19 - The Trans-Alaska pipeline is 1 300 km long,...Ch. 19 - Prob. 14PCh. 19 - Prob. 15PCh. 19 - Prob. 16PCh. 19 - Prob. 17PCh. 19 - Why is the following situation impossible? A thin...Ch. 19 - A volumetric flask made of Pyrex is calibrated at...Ch. 19 - Review. On a day that the temperature is 20.0C, a...Ch. 19 - Prob. 21PCh. 19 - Prob. 22PCh. 19 - Prob. 23PCh. 19 - Prob. 24PCh. 19 - Prob. 25PCh. 19 - Prob. 26PCh. 19 - Prob. 27PCh. 19 - Prob. 28PCh. 19 - Prob. 29PCh. 19 - Prob. 30PCh. 19 - An auditorium has dimensions 10.0 m 20.0 m 30.0...Ch. 19 - Prob. 32PCh. 19 - Prob. 33PCh. 19 - Prob. 34PCh. 19 - Prob. 35PCh. 19 - In state-of-the-art vacuum systems, pressures as...Ch. 19 - Prob. 37PCh. 19 - Prob. 38PCh. 19 - Prob. 39PCh. 19 - Prob. 40PCh. 19 - Prob. 41PCh. 19 - Prob. 42PCh. 19 - Prob. 43PCh. 19 - The pressure gauge on a cylinder of gas registers...Ch. 19 - Prob. 45APCh. 19 - Prob. 46APCh. 19 - Prob. 47APCh. 19 - Prob. 48APCh. 19 - Prob. 49APCh. 19 - Why is the following situation impossible? An...Ch. 19 - Prob. 51APCh. 19 - Prob. 52APCh. 19 - Prob. 53APCh. 19 - Prob. 54APCh. 19 - A student measures the length of a brass rod with...Ch. 19 - Prob. 56APCh. 19 - A liquid has a density . (a) Show that the...Ch. 19 - Prob. 59APCh. 19 - Prob. 60APCh. 19 - The rectangular plate shown in Figure P19.61 has...Ch. 19 - Prob. 62APCh. 19 - Prob. 63APCh. 19 - Prob. 64APCh. 19 - Prob. 65APCh. 19 - Prob. 66APCh. 19 - Prob. 67APCh. 19 - Prob. 68APCh. 19 - Prob. 69APCh. 19 - Prob. 70APCh. 19 - Prob. 71APCh. 19 - Prob. 72CPCh. 19 - Prob. 73CPCh. 19 - Prob. 74CPCh. 19 - Prob. 75CPCh. 19 - Prob. 76CPCh. 19 - Prob. 77CPCh. 19 - Prob. 78CPCh. 19 - A 1.00-km steel railroad rail is fastened securely...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A vertical cylinder of cross-sectional area A is fitted with a tight-fitting, frictionless piston of mass m (Fig. P16.56). The piston is not restricted in its motion in any way and is supported by the gas at pressure P below it. Atmospheric pressure is P0. We wish to find die height h in Figure P16.56. (a) What analysis model is appropriate to describe the piston? (b) Write an appropriate force equation for the piston from this analysis model in terms of P, P0, m, A, and g. (c) Suppose n moles of an ideal gas are in the cylinder at a temperature of T. Substitute for P in your answer to part (b) to find the height h of the piston above the bottom of the cylinder.arrow_forwardA vertical cylinder of cross-sectional area A is fitted with a tight-fitting, frictionless piston of mass m (Fig. P18.40). The piston is not restricted in its motion in any way and is supported by the gas at pressure P below it. Atmospheric pressure is P0. We wish to find the height h in Figure P18.40. (a) What analysis model is appropriate to describe the piston? (b) Write an appropriate force equation for the piston from this analysis model in terms of P, P0, m, A, and g. (c) Suppose n moles of an ideal gas are in the cylinder at a temperature of T. Substitute for P in your answer to part (b) to find the height h of the piston above the bottom of the cylinder. Figure P18.40arrow_forwardConsider a 300-L storage tank of a solar water heating system initially filled with warm water at 45°C. Warm water is withdrawn from the tank through a 2-cm diameter hose at an average velocity of 0.5 m/s while cold water enters the tank at 20°C at a rate of 5 L/min. Determine the amount of water in the tank after a 20-minute period. Assume the pressure in the tank remains constant at 1 atm.arrow_forward
- A cylinder with a diameter of 5.64 cm has a movable piston attached to a spring as shown in Figure P.40. The cylinder contains 1.32 liters of an ideal gas at 17.8°C and 0.93 atm pressure. After the gas is heated briefly and allowed to expand, it is found that the spring compresses 3.42 cm and the temperature of the gas increases to 103°C. What is the change in volume for this expansion?_______ mLWhat is the change in pressure?_______ atmWhat is the spring constant k?_______ N/marrow_forwardAn automobile engine works by injecting a fuel and air mixture into a cylinder with a piston. Once this mixture is injected, the piston compresses the mixture by a factor of 9, meaning that the volume is reduced by 1/9. Assume that the initial temperature is 25°C. Assume that the initial pressure is 1.00 atmospheres and the final pressure is 21.7 atmospheres. Treat the air-fuel mixture as an ideal gas. What is the temperature of the compressed mixture? A 723 K 745 K C 719 K 333 Karrow_forwardA pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve indicate the direction of the process, and the points of interest are labeled. The values 1 for the points in the diagram are shown in the table. Volume (m³) Pressure (Pa) Vo 25.8 Po = 1.00 x 104 3 Vi = 20.8 Pi = 1.00 × 104 V2 = 17.4 P2 5.34 x 103 V3 = 13.9 P3 5.34 x 103 V4 13.9 P4 3.20 x 103 5 Vs = 9.55 P5 = 1.00 x 103 Calculate the amount of work done on the system from 0-2 ( Wo2) and then for the entire curve from 0-5 (Wos). Volume (m³) -6.03 x104 Wo2 = J Incorrect -7.86 x104 Wo5 = J Incorrect Pressure (Pa)arrow_forward
- A high-pressure gas cylinder contains 70.0 L of toxic gas at a pressure of 2.10 x 107 N/m2 and a temperature of 14.0°C. Its valve leaks after the cylinder is dropped. The cylinder is cooled to dry Ice temperatures (-78.5°C), to reduce the leak rate and pressure so that it can be safely repaired. (a) What is the final pressure in the tank, assuming a negligible amount of gas leaks while being cooled and that there is no phase change? N/m² (b) What is the final pressure if one-tenth of the gas escapes? N/m² (c) To what temperature must the tank be cooled to reduce the pressure to 1.00 atm (assuming the gas does not change phase and that there is no leakage during cooling)? K Additional Materialsarrow_forwardA pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve indicate the direction of the process, and the points of interest are labeled. The values for the points in the diagram are shown in the table. Volume (m³) Pressure (Pa) Vo = 25.8 Po = 1.00 × 10ª %3D 2 3 Vị = 20.8 Рі 3D 1.00 х 104 V2 = 17.4 P2 = 5.34 × 103 V3 13.9 P3 = 5.34 x 103 4 V4 = 13.9 P4 = 3.20 × 10³ %3| Vs = 9.55 P5 = 1.00 x 103 %3D Calculate the amount of work done on the system from 0–2 ( Wo2) and then for the entire curve from 0-5 (Wo5). Volume (m³) 79.81 x103 Wo2 J Incorrect 107.09 x103 Wo5 J Incorrect Pressure (Pa)arrow_forwardA pressure versus volume (pv) diagram for a system is shown in the figure. The arrows of the curve indicate the direction of the process, and the points of interest are labeled. The values for the points in the diagram are shown in the table. Volume (m3) Pressure (Pa) v0=27.4 p0=1.00×104 v1=19.3 p1=1.00×104 v2=16.0 p2=4.92×103 v3=13.3 p3=4.92×103 v4=13.3 p4=3.20×103 v5=7.51 p5=1.00×103 Calculate the amount of work done on the system from 0–2 (W02) and then for the entire curve from 0–5 (W05).arrow_forward
- Water at 15°C is to be pumped from a reservoir (zA = 2 m) to another reservoir at a higher elevation (zB = 9 m) through two 25-m-long plastic pipes connected in parallel. The diameters of the two pipes are 3 cm and 5 cm. Water is to be pumped by a 68 percent efficient motor–pump unit that draws 8 kW of electric power during operation. The minor losses and the head loss in the pipes that connect the parallel pipes to the two reservoirs are considered to be negligible. Determine the total flow rate between the reservoirs and the flow rates through each of the parallel pipes.arrow_forwardA high-pressure gas cylinder contains 70.0 L of toxic gas at a pressure of 1.40 x 107 N/m² and a temperature of 16.0°C. Its valve leaks after the cylinder is dropped. The cylinder is cooled to dry ice temperatures (-78.5°C), to reduce the leak rate and pressure so that it can be safely repaired. (a) What is the final pressure in the tank, assuming a negligible amount of gas leaks while being cooled and that there is no phase change? 9.42e6 N/m² (b) What is the final pressure if one-tenth of the gas escapes? 8.61e6 N/m² (c) To what temperature must the tank be cooled to reduce the pressure to 1.00 atm (assuming the gas does not change phase and that there is no leakage during cooling)? 2.14 Review the values for initial and final pressure for this situation. Karrow_forwardA cell doesn’t need a circulatory system, but your body does. Let’s do a quick calculation to see why. A typical cell has a diameter of 10 mm. The smallest mammals in the world, shrews, are about 10 μm across. Compute the diffusion time for oxygen molecules through water at 25°C for these two distances.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning