ELECTRICAL WIRING:RESIDENTAL-6 PLANS
18th Edition
ISBN: 9781305098329
Author: MULLIN
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19.2, Problem 19R
A condominium owner complains of not getting enough hot water. The serviceman checks the voltage at the water heater and finds the voltage to be 208 volts. The serviceman checks further and finds the electrical service on the building to be a 120/208-volt, three-phase, 4-wire system. The main electrical panelboard for each condominium unit is fed with a 3-wire supply. The nameplate on the electric water heater is marked 4500 watts, 240 volts. What is the wattage output of the heating element in this water heater when connected to a 208-volt supply? _____________________
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2. A facility manager replaces all the TS lights in an office when they have reached 80% of their
rated life of 20,000 hours. The lights operate for 12 hours each day, 5 days per week for 52
weeks of the year. What is the group re-lamping interval for these lights?
a.
3.7 years
b.
4.6 years
c. 5.1 years
d. 6.4 years
6.
when seeking to measure the voltage of an industrial power supply (600 Volts AC) an
electrician needs to do the following to prepare the Simpson 260 meter for
measurement (insert the words to make the following statements correct).
a. Set the function switch to
b. The black lead should be inserted in the
jack.
C. The red lead should be inserted in the
jack.
d. The range switch should be set to the
position.
Did you note the safety warnings in this section? Fairly significant, eh?!
Nothing to mess around with!!
7.
Why must you "zero" the meter (adjust it for zero (0)) when measuring resistance?
8.
Describe the steps needed to accomplish the task of zeroing the meter. (4pts)
For the following questions, refer to section 4.19 in the Simpson meter manual.
9.
The Rx 1 resistance range is intended for resistances between
and
Ω.
10. The R x 100 range is intended for resistances between
and
Ω.
11. The Rx 10,000 range is intended for resistances over
0450…
If the per unit reactance of a power system up to the fault point is 0.2pu and base power (VAb) is
10 MVA, then the fault level (VAsc) is
O 2 MVA
O 100 MVA
50 MVA
O 500 MVA
Chapter 19 Solutions
ELECTRICAL WIRING:RESIDENTAL-6 PLANS
Ch. 19.1 - Does a jet pump have any electrical moving parts...Ch. 19.1 - Prob. 2RCh. 19.1 - Where is the jet of the pump located?...Ch. 19.1 - Prob. 4RCh. 19.1 - Prob. 5RCh. 19.1 - Prob. 6RCh. 19.1 - Prob. 7RCh. 19.1 - What is compressed in the water storage tank?...Ch. 19.1 - Explain the difference between a 2-wire...Ch. 19.1 - Prob. 10R
Ch. 19.1 - Why is a 240-volt motor preferable to a 120-volt...Ch. 19.1 - How many amperes does a 1-horsepower, 240-volt,...Ch. 19.1 - What size are the conductors used for this branch...Ch. 19.1 - Prob. 14RCh. 19.1 - What provides the running overload protection for...Ch. 19.1 - What is the maximum ampere setting permitted for...Ch. 19.1 - Prob. 17RCh. 19.1 - Because the controller contains the motor starting...Ch. 19.1 - Prob. 19RCh. 19.1 - Proper pressure of the submersible pump system is...Ch. 19.1 - Fill in the data for a 16-ampere electric motor,...Ch. 19.1 - The NEC is very specific in its requirement that...Ch. 19.1 - Does the NEC allow submersible pump cable to be...Ch. 19.1 - Must the disconnect switch for a submersible pump...Ch. 19.1 - A metal well casing (shall) (shall not) be bonded...Ch. 19.2 - Prob. 1RCh. 19.2 - A major hazard involved with water heaters is that...Ch. 19.2 - Prob. 3RCh. 19.2 - The heating elements in electric water heaters are...Ch. 19.2 - An 80-gallon electric water heater is energized...Ch. 19.2 - Prob. 6RCh. 19.2 - For residential water heaters, the Consumer...Ch. 19.2 - An 80-gallon electric water heater has 60F...Ch. 19.2 - Approximately how long would it take to produce...Ch. 19.2 - Two thermostats are generally used in an electric...Ch. 19.2 - a. How many heating elements are provided in the...Ch. 19.2 - When does the lower heating element operate?...Ch. 19.2 - Prob. 14RCh. 19.2 - Prob. 15RCh. 19.2 - Prob. 16RCh. 19.2 - a. If both elements of the water heater in this...Ch. 19.2 - a. How much power in watts would the two elements...Ch. 19.2 - A condominium owner complains of not getting...Ch. 19.2 - For a single, nonmotor-operated electrical...Ch. 19.2 - A 7000-watt resistance-type heating appliance is...Ch. 19.2 - Prob. 22R
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of these places has the highest voltage in a properly working truck electrical system with the engine running and the batteries charging? A. Across battery terminals B. Across cranking motor B+ and cranking motor ground C. Across the alternator plus output stud and alternator ground stud cranking motor ground D. All of the above would be the exact same voltagearrow_forwardLoad in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a maintenance engineer, you need to proposed cable size for the load, Determine the following issues. 1) Calculate current demand for the circuit. 1) Detemine suitable MCCB (Model and nominal current rating) should be used to protect the load against over-current. im Propose suitable cable size for the load in Figure 1. iv) Calculate voltage drop of the proposed cable WITHOUT consider the cable reactance and voltage drop correction due to higher cable operating temperature v) Calculate voltage drop of the proposed cable BY consider the cable reactance and voltage drop correction due to higher cable operatıng temperature vi) If the multicore PVC eable is change into 3 single core PVC cables, what the suitable cable size. All other multicore cables not available. (25 + variable x) m (A) 30 m (B) (15 + variable b) m (C) Multicore PVC cable MCCB 95 kW. (400 + variable y) V. 0.85 p.f. Load MSB…arrow_forwardAn uncharged condenser in series with a 120V voltmeter of 10,000 ohms resistance is suddenly connected to a 100V battery. One second later, the voltmeter reads 60 volt. Determine the capacitance of the condenser. *Round off the final answer to the nearest 4 decimal places with unit. Rounding off should only be done on final answer.arrow_forward
- According to the following specifications, a single solar 295-watt solar panel has maximum power operation voltage at 24 volts. What is the maximum number of solar panels that can be used in a single string? a. 35 solar panels. b. 30 solar panels. c. 25 solar panels. d. 40 solar panels. e. 20 solar panels.arrow_forwardmatch column a to b. Electricity flows from the power plant Through wires to the step-up transformer. The transformer raises the voltage so it can travel long distances - it is raised as high as 756,000 volts. Electricity is generated in the power plant by hydroelectric, nuclear, wind or geothermal energy. The electric current then runs through the power lines to the substation transformer where voltage is lowered to between 2000 and 13000 volts. The turbine spins a huge magnet inside a copper wire. Heat energy converts to mechanical energy which then converts to electrical energy in the generator. From there, electricity comes into your home through a service box, where your heter IS located to electrical consumption. measure your Wires Taice electricity around your home, powering your lights and all your other electrical appliances. Electricity is then taken through the lines to a pole transformer or transformer box if underground then the voltage is lowered again to 120 or 220…arrow_forwardh.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor isA. 250 kcmil.B. 3/0.C. 500 kcmil.D. 4/0. h.2. The figure shows a fault condition in an ungrounded electrical system. Which of the following will occurbecause of the fault in this system?A. Only the overcurrent protector at Point A will trip open.B. The ground fault will heavily damage the service.C. Nothing will happen until a second ground fault occurs.D. The overcurrent protection will trip, shutting off all the line side power.arrow_forward
- Lamp outlets Duplex convenience outlets Single gang switches Two gang switch Three gang switch Count the number of the following.arrow_forwardWe are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"arrow_forwardFour electricians are discussing wiring under raised floors in information technology equipment rooms. Electrician A says that wiring under the raised floor requires fire-resistant walls, floors, and ceilings between other occupancies. Electrician B says that wiring under the raised floor requires fire resistant halfway up the walls and floors between other occupancies. Electrician C says that the room must employ a disconnecting means that removes half of the power to all equipment in the room. Electrician D says that a disconnecting means isn't necessary for the room. Which of the following statements is correct? A. Electrician B is correct. B. Electrician D is correct. C. Electrician A is correct. D. Electrician C is correct.arrow_forward
- c) Based on the Figure 1 (c), a 240V circuit supplies power to an electrical appliance. Based on the figure, briefly interpret the scenarios if: i. Fault is detected on hot/live wire ii. Ground wire disconnected Fault breaker Hot wire Service panel The resistor symbol represents all the internal components of an appliance like a washing machine. Neutral Neutral to supply transformer Ground wire Figure 1 (c)arrow_forwardWrite a short essay about the difference between an indoor and an outdoor substation. Compare each substation in terms of operation, and setup. specifications,arrow_forwardin the circuit, the voltage across R1 in volts is ___ in the circuit, the voltage across R2 in volts is ___ in the circuit, the voltage across R3 in volts is ___arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
What is an electric furnace and how does it work?; Author: Fire & Ice Heating and Air Conditioning Inc;https://www.youtube.com/watch?v=wjAWecPGi0M;License: Standard Youtube License