Fill in the data for a 16-ampere electric motor, single-phase, no Code letters.
- a. Branch-circuit protection, non-time-delay fuses:
Normal size _____________A Maximum size _____________A
Switch size _____________A Switch size _____________A
- b. Branch-circuit protection dual-element, time-delay fuses:
Normal size _____________A Maximum size _____________A
Switch size _____________A Switch size _____________A
- c. Branch-circuit protection instant-trip breaker:
Normal setting _____________A
Maximum setting _____________A
- d. Branch-circuit protection—inverse time breaker:
Normal rating _____________A
Maximum rating _____________A
- e. Branch-circuit conductor size, Type THHN
Ampacity _____________A
- f. Motor overload protection using dual-element time-delay fuses:
Maximum size _____________A
Trending nowThis is a popular solution!
Chapter 19 Solutions
ELECTRICAL WIRING:RESIDENTAL-6 PLANS
Additional Engineering Textbook Solutions
Introductory Circuit Analysis (13th Edition)
Electric Circuits. (11th Edition)
ELECTRICITY FOR TRADES (LOOSELEAF)
Basic Engineering Circuit Analysis
Principles Of Electric Circuits
Programmable Logic Controllers
- Draw the power circuit and control circuit of a Direct On Line Motor Starter fo a three-phase motor. Add 4 pilot lights (PL) in the control circuit; red PL for running forward, orange PL for running in reverse, green for not running and yellow for overload.1. List the components used. 2. Procedures.arrow_forwarda" printed-circuit motor" is another term for a _________motor.arrow_forward(b) () Discuss the cascade control scheme for a heat exchanger system with a neat diagram. (ii) List down any two merits and two demerits of a cascade control system over ratio control system.arrow_forward
- Sketch the electronic symbol (schematic) for the following components/ devices. Briefly describe the function of the electronic component and use the IEEE/ANSI standard symbol as indicated below. Component/ Device IEEE/ANSI Standard Symbol Function 1. Wire 2. Wires joined 3. Wires not joined 4. Cell 5. Battery 6. DC Supply 7. AC Supply 8. Fuse 9. Transformer 10. Ground (Common) 11. Lamp (Lighting) 12. Lamp (Indicator) 13. Heaterarrow_forwardQUESTION 13 The resistance of the Armature's conductor coil(s) in most motors is: quite high, usually a few thousand ohms or more depending on the size of the motor. Typically an open circuit value on most multimeters quite low, usually a few ohms or less depending on the size of the motor. very high, usually in the megaohms.arrow_forwardAll answers should be written in complete sentences. Calculations should be shown in detail, and Codereferences should be cited when appropriate. Unless otherwise stated, all conductors are copper type THHN, and the supply is AC. 1. What is the minimum conductor ampacity, overload protection, and dual-element fuserating for a circuit supplying a 560-volt, 3-phase, code J, 40°C, 125-horsepower motorwith a nameplate full-load current of 115 amperes?arrow_forward
- The amount of short-circuit current from a motor is equal approximately to_current for each motor. A.accelerating b. locked-rotor c. stator d. finalarrow_forwardTechnician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or Barrow_forward460VAC squirrel cage, 60 hp, 3 phase induction-type AC motor, is to be controlled with 220VAC rated magnetic contactor. Control circuit will be supplied with 110VAC. What is the full-load current and the conductor size.arrow_forward
- With the aid of block diagram/circuit connection and relevant equations, describe the working principle of following systems. Emphasis should be given on usage of power electronic converter in the system. Uninterrupted Power Supply(UPS). 2. C Motor Drive.arrow_forwardThe pointer moving across a scale in the speedo meter is an example for ___________ of the instrumentation system. a.Feed back element b.Sensing element c.Data presentation element d.Signal conditioning elementarrow_forward8.a. Which of the following most accurately describes the difference between a contactor and a starter?A. A starter contains a contactor and some additional protective circuitry.B. A starter is always mounted in an enclosure.C. A starter contains reversing contacts.D. A starter is always three-phase while a contactor may be single-phase or three-phase.8.b. The main bus in a motor control center is used toA. reduce the possibility of overload with large loads.B. enclose motors within a protective shield.C. distribute power to all starters in the center.D. reduce the voltage of the plant's supply.arrow_forward