Engineering Mechanics
14th Edition
ISBN: 9780133951929
Author: HIBBELER, Russell C.
Publisher: Pearson Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19.4, Problem 35P
The 2-kg rod ACB supports the two 4-kg disks at its ends If both disks are given a clockwise angular velocity (ωA)1 = (ωB)1 = 5 rad/s while the rod is held stationary and then released, determine the angular velocity of the rod after both disks have stopped spinning relative to the rod due to frictional resistance at the pins A and B. Motion is in the horizontal plane. Neglect friction at pin C.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
Chapter 19 Solutions
Engineering Mechanics
Ch. 19.2 - Determine the angular momentum of the 100-kg disk...Ch. 19.2 - Determine the angular impulse about point O for t...Ch. 19.2 - If it is subjected to a couple moment of M = (3t2)...Ch. 19.2 - The 300-kg wheel has a rad1us of gyration about...Ch. 19.2 - If rod OA of negligible mass is subjected lo the...Ch. 19.2 - Gears A and B of mass 10 kg and 50 kg have radii...Ch. 19.2 - The 50-kg spool is subjected to a horizontal force...Ch. 19.2 - The reel has a weight of 150 lb and a radius of...Ch. 19.2 - The rigid body (slab) has a mass m and rotates...Ch. 19.2 - At a given Instant, the body has a linear momentum...
Ch. 19.2 - Show that if a slab is rotating about a fixed axis...Ch. 19.2 - The 40-kg disk is rotating at = 100 rad/s. When...Ch. 19.2 - The Impact wrench cons1sts of a slender 1-kg rod...Ch. 19.2 - The airplane is traveling in a straight line with...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The assembly weighs 10 lb and has a radius of...Ch. 19.2 - The disk has a weight of 10 lb and is pinned at...Ch. 19.2 - The 30-kg gear A has a radius of gyration about...Ch. 19.2 - Determine the angular velocity of the pulley when...Ch. 19.2 - The 40-kg roll of paper rests along the wall where...Ch. 19.2 - The slender rod has a mass m and is suspended at...Ch. 19.2 - The rod of length L and mass m lies on a smooth...Ch. 19.2 - A 4-kg disk A is mounted on arm BC. which has a...Ch. 19.2 - The frame of a tandem drum roller has a weight of...Ch. 19.2 - The 100-lb wheel has a radius of gyration of kG =...Ch. 19.2 - The 4-kg slender rod rests on a smooth floor If it...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The 100-kg spool is resting on the inclined...Ch. 19.2 - The spool has a weight of 30 lb and a radius of...Ch. 19.2 - The two gears A and B have weights and radii of...Ch. 19.2 - The hoop (thin ring) has a mass of 5 kg and is...Ch. 19.2 - The 30-kg gear is subjected to a force of P =...Ch. 19.2 - The 30-lb flywheel A has a radius of gyration...Ch. 19.2 - If the shaft is subjected to a torque of M = (...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The crate has a mass mc. Determine the constant...Ch. 19.4 - The turntable T of a record player has a mass of...Ch. 19.4 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19.4 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19.4 - The circular disk has a mass m and is suspended at...Ch. 19.4 - The 80-kg man is holding two dumbbells while...Ch. 19.4 - The platform swing consists of a 200-lb flat plate...Ch. 19.4 - The 2-kg rod ACB supports the two 4-kg disks at...Ch. 19.4 - The satellite has a mass of 200 kg and a radius of...Ch. 19.4 - Disk A has a weight of 20 lb. An inextensible...Ch. 19.4 - The plank has a weight of 30 lb, center of gravity...Ch. 19.4 - The 12-kg rod AB is pinned to the 40-kg disk. If...Ch. 19.4 - A thin rod of mass m has an angular velocity o...Ch. 19.4 - Tests of impact on the fixed crash dummy are...Ch. 19.4 - The vertical shaft is rotating with an angular...Ch. 19.4 - The mass center of the 3-lb ball h3s a velocity of...Ch. 19.4 - Prob. 44PCh. 19.4 - The 10-lb block is sliding on the smooth surface...Ch. 19.4 - Determine the height hat which a billiard ball of...Ch. 19.4 - The pendulum consists of a 15-kg solid ball and...Ch. 19.4 - The 4-lb rod AB is hanging in the vertical...Ch. 19.4 - Determine the largest angular velocity 1 the disk...Ch. 19.4 - The solid ball of mass m is dropped with a...Ch. 19.4 - The wheel has a mass of 50 kg and a radius of...Ch. 19.4 - The wheel has a mass of 50 kg and a radius of...Ch. 19.4 - The rod of mass m and length L is released from...Ch. 19.4 - Prob. 55PCh. 19.4 - A ball having a mass of 8 kg and initial speed of...Ch. 19.4 - A solid ball with a mass m is thrown on the ground...Ch. 19.4 - The pendulum consists of a 10-lb solid ball and...Ch. 19.4 - The cable is subjected to a force of P = (10t2)...Ch. 19.4 - The space capsule has a mass of 1200 kg and a...Ch. 19.4 - The tire has a mass of 9 kg and a rad1us of...Ch. 19.4 - The wheel having a mass of 100 kg and a radius of...Ch. 19.4 - The spool has a weight of 30 lb and a radius of...Ch. 19.4 - Spool B is at rest and spool A is rotating at 6...Ch. 19.4 - A thin disk of mass m has an angular velocity 1...Ch. 19.4 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The smooth surface of the vertical cam is defined in part by the curve r =(0.2 cos θ + 0.3) m. The forked rod is rotating with an angular acceleration of 2rad/s^2, and when θ = 45° the angular velocity is 6 rad/s. Determine the force the camand the rod exert on the 2-kg roller at this instant. The attached spring has a stiffnessk = 100 N/m and an unstretched length of 0.1 m.arrow_forwardThe 12-kg slender rod is pinned to a small roller A that slides freely along the slot. If the rod is released from rest at f) = 0°, determine the angular acceleration of the rod and the acceleration of the roller immediately after the release.arrow_forwardThe double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 32 kg and a radius of gyration k_O = 260 mm. The men A and B have a mass of 60 kg and 70 kg, respectively. Assume they do not move relative to the rope during the motion. Neglect the mass of the rope. If two men A and B grab the suspended ropes and step off the ledges at the same time, determine the speed of man A in 4.2 s starting from rest. vA= ??? If two men A and B grab the suspended ropes and step off the ledges at the same time, determine the speed of man B in 4.2 s starting from rest. vB= ???arrow_forward
- The spring-held follower AB has a mass of 0.4 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z=(0.02cos2θ)m. The cam is rotating at a constant rate of 30 rad/s. The spring is uncompressed when θ = 90. Determine the maximum force component FzFz the follower exerts on the cam. Determine the minimum force component FzFz the follower exerts on the cam.arrow_forwardThe trailer has a mass of 400kg and the mass center at G. is being pulled by a horizontal force of magnitude of F = 800N. Determine the acceleration of the trailer, as well as the normal forces (Na and Nb) on the pair of wheels at A and B respectively. Assume the wheels are free to roll and have negligible mass.arrow_forwardThe particle of mass m = 2.4 kg is attached to the light rigid rod of length L = 0.77 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙θ˙ = ω = 3.5 rad/s. Determine the force T in the rod when θ = 29°. The force T is positive if in tension, negative if in compression.arrow_forward
- The particle of mass m = 2.1 kg is attached to the light rigid rod of length L = 0.91 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙θ˙ = ω = 2.9 rad/s. Determine the force T in the rod when θ = 28°. The force T is positive if in tension, negative if in compression. Determine the force T in the rod when θ = 28°. The force T is positive if in tension, negative if in compression.arrow_forwardDetermine the velocity of the cylinder A when t=4s if the system is released from rest. Cylinder A has mass of 8kg and cylinder B has a mass of 6kg. Neglect the mass of the pulleys and cords.arrow_forward5. The 25-kg block AA is released from rest.arrow_forward
- The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheelsarrow_forward15-102. The two spheres each have a mass of 3 kg and are attached to the rod of negligible mass. Determine the time the torque M = (8t) N·m where, is in seconds, must be applied to the rod so that each sphere attains a speed of 3 m/s starting from restarrow_forwardThe 0.2-Kg pin P is constrained to move in the smooth curved slot. Which is defined by the lemniscate r = (0.6cos 2theta) m. Its motion is controlled by the rotation of the slotted arm OA, which has a constant clockwise angular velocity of dot theta =-3 rad/s . Determine (a)-the force arm OA exerts on the pin P when theta = 0 ^ 0 ,note that the motion is in the vertical plane, (b) the acceleration in the r and 0 direction. r = (0.0cos 2theta) m 4arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License