Fundamentals of Electromagnetics with Engineering Applications
1st Edition
ISBN: 9780470105757
Author: Stuart M. Wentworth
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 2, Problem 2.56P
A nickel wire of diameter 5.0 mm is surrounded by a 0.50–mm–thick layer of silver. What is the resistance per unit length for this wire? Assuming 1.0 m of this wire caries 1.0 A of current, determine the power dissipated in the nickel portion and in the silver portion of the wire.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A long copper wire carries a current of 15A which is evenly distributed in each cross-section of the wire. If the diameter of the wire is 3 mm, and the resistance per unit length is 4 ohm/km. Calculate the density of the magnetic and electric fields on the surface of the wire.
5. A long copper wire carries a current of 20A which is evenly distributed in each cross-section of the wire. If the diameter of the wire is 4 mm, and the resistance per unit length is 5 Q2/km, calculate the energy density of the magnetic and electric fields on the surface of the wire!
Neglecting losses and fringing effects and assuming the substrate of a stripline to have a thickness of 0.42 (mm) and a dielectric constant of 2.83, determine the required width (in mm) of the metal strip in order for the stripline to have characteristics resistance of 78 Ohms. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.
Chapter 2 Solutions
Fundamentals of Electromagnetics with Engineering Applications
Ch. 2 - Given P(4, 2, 1) and APQ=2ax+4ay+6az, find the...Ch. 2 - Prob. 2.2PCh. 2 - Prob. 2.3PCh. 2 - Suppose Q1(0.0,-3.0m,0.0)=4.0nC,...Ch. 2 - Prob. 2.5PCh. 2 - Suppose 10.0nC point charges are located on the...Ch. 2 - Four 1.00nC point charges are located at...Ch. 2 - A 20.0nC point charge exists at...Ch. 2 - Prob. 2.9PCh. 2 - Convert the following points from Cartesian to...
Ch. 2 - Prob. 2.11PCh. 2 - Prob. 2.12PCh. 2 - Prob. 2.13PCh. 2 - A 20.0–cm–long section of copper pipe has a...Ch. 2 - A line charge with charge density 2.00nC/m exists...Ch. 2 - You are given two z–directed line charges of...Ch. 2 - Suppose you have a segment of line charge of...Ch. 2 - A segment of line charge L=10.nC/m exists on the...Ch. 2 - In free space, there is a point charge Q=8.0nC at...Ch. 2 - Prob. 2.20PCh. 2 - Sketch the following surfaces and find the total...Ch. 2 - Consider a circular disk in the x–y plane of...Ch. 2 - Suppose a ribbon of charge with density S exists...Ch. 2 - Sketch the following volumes and find the total...Ch. 2 - You have a cylinder of 4.00–in diameter and...Ch. 2 - Consider a rectangular volume with...Ch. 2 - Prob. 2.27PCh. 2 - Prob. 2.28PCh. 2 - Given D=2a+sinazC/m2, find the electric flux...Ch. 2 - Suppose the electric flux density is given by...Ch. 2 - Prob. 2.31PCh. 2 - A cylindrical pipe with a 1.00–cm wall thickness...Ch. 2 - Prob. 2.34PCh. 2 - Prob. 2.35PCh. 2 - A thick–walled spherical shell, with inner...Ch. 2 - Prob. 2.37PCh. 2 - Determine the charge density at the point...Ch. 2 - Given D=3ax+2xyay+8x2y3azC/m2, (a) determine the...Ch. 2 - Suppose D=6cosaC/m2. (a) Determine the charge...Ch. 2 - Suppose D=r2sinar+sincosaC/m2. (a) Determine the...Ch. 2 - Prob. 2.42PCh. 2 - A surface is defined by the function 2x+4y21nz=12....Ch. 2 - For the following potential distributions, use the...Ch. 2 - A 100nC point charge is located at the origin. (a)...Ch. 2 - Prob. 2.46PCh. 2 - Prob. 2.47PCh. 2 - Prob. 2.48PCh. 2 - Suppose a 6.0–m–diameter ring with charge...Ch. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - The typical length of each piece of jumper wire on...Ch. 2 - A 150–m length of AWG–22 (0.644 mm diameter)...Ch. 2 - Determine an expression for the power dissipated...Ch. 2 - Find the resistance per unit length of a stainless...Ch. 2 - A nickel wire of diameter 5.0 mm is surrounded by...Ch. 2 - Prob. 2.57PCh. 2 - A 20nC point charge at the origin is embedded in...Ch. 2 - Suppose the force is very carefully measured...Ch. 2 - The potential field in a material with r=10.2 is...Ch. 2 - In a mineral oil dielectric, with breakdown...Ch. 2 - Prob. 2.62PCh. 2 - For z0,r1=9.0 and for z0,r2=4.0. If E1 makes a 300...Ch. 2 - Prob. 2.64PCh. 2 - Consider a dielectric–dielectric charge–free...Ch. 2 - A 1.0–cm–diameter conductor is sheathed with a...Ch. 2 - Prob. 2.67PCh. 2 - For a coaxial cable of inner conductor radius a...Ch. 2 - Prob. 2.69PCh. 2 - Prob. 2.70PCh. 2 - A parallel–plate capacitor with a 1.0m2 surface...Ch. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Given E=5xyax+3zaZV/m, find the electrostatic...Ch. 2 - Suppose a coaxial capacitor with inner radius 1.0...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The numbers of orbiting electrons in aluminum and silver are 13 and 47, respectively. Draw the electronic confi...
Introductory Circuit Analysis (13th Edition)
The switch shown in Fig. P 7.4 has been open for a long time before closing at t = 0.
Figure P7.4
Find io(0−),...
Electric Circuits (10th Edition)
Design a differential amplifier with inputs v1 and v2 and an output vO=100(v2v1) using only one OP AMP. All res...
ANALYSIS+DESIGN OF LINEAR CIRCUITS(LL)
Find C(t) for t0 in the network in Fig. P7.26 using the step-by-step method.
Basic Engineering Circuit Analysis
Explain Faradays law and the function of Lenzs law.
Fundamentals of Applied Electromagnetics (7th Edition)
Determine the value of vx and iy in the circuit shown in Figure P1.71. Figure P1.71
Electrical Engineering: Principles & Applications (7th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is a proton? Where does it normally exist in an atom, and what is its charge?arrow_forwardCompute the conductivity of the given material whose resistivity is ρ=1.724∗10−8Ωm area of cross-section and length are 10cm2 and 15cm respectively?arrow_forwardA copper wire at 20 degrees C, and 164 cmil, has a K value of 10.4 ohms per mi-foot. If the distance to the load is 600 feet (183 m) calculate the resistance of the loop.arrow_forward
- A company wants to produce a ductile material with improved properties. Would impurity atoms of similar or dissimilar atomic size be better at maintaining the ductility of a metal?How does the impurities affect the crystal structure and properties of a solid?Justify your answer with a valid reasoning.arrow_forwardCompute for the resistance of (i) silver, (ii) copper, and (iii) aluminum wire using these Equations in the given. For the three wires, the length is 2 meters, the diameter is 1 millimeter, and the temperature is at 27◦C.arrow_forwardThe wires of our appliances are insulated with a material mixed with rubber, which has a very high resistivity. If a certain wire has a length of 2.5 m and the outer diameter is 5mm and its inner diameter is 0.5mm, what is its resistance? Note that the inner diameter is present to leave a hallow place where conducting wire ( usually copper) is present. Follow the format: Given: Required: Equation: Solution: Answer:arrow_forward
- An AWG #10 copper wire conductor has an 80.8 mil diameter. A 50-foot length carries a current of 30 Amperes. Find the electric field intensity E within the wire, the voltage drop across the conductor, and the resistance R of the 100-foot length.arrow_forwardAccording to the figure below, wire section 1 of diameter D1 = 8 R and wire section 2 of diameter D2= 4R connected by a tapered section. The wire is copper, its resistivity uniformly distributed across any cross-section area through the wire's width. The electric potential change V along the length L = 4 m shown in section 2 is 20 µV. The number of charge carriers per unit volume is 8.49 x 1028 m3.What is the drift speed of the conduction electrons in section. 1.69 x 10-8 Qm and carriers a current. Assume that the current isarrow_forwardConductors A conducting wire is 2 mm in radius and 100 m in length. When a dc voltage of 9 Vis applied to the wire, it results in a current of 0.3 A. Find: The E-field in the wire, The conductivity of the wire.arrow_forward
- Based on the definition of ∆V and current density J⃗ = σE⃗ , discuss the consequence of having a pinched wire running current to some device like the light in the last problem. (By pinched, expect that the cross section is decreased at one spot.)arrow_forwardCompute the resistivity of the given material whose resistance is 2 Ω; area of cross-section and length are 25cm2 and 15 cm respectively?arrow_forwardA copper wire 100 m long must experience avoltage drop of less than 1.5 V when a current of 2.5 A passesthrough it. Given that copper has an electrical conductivity of6.0E7 /(Ὠ-m), compute the minimum diameter of the wire.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningElectricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning
Conductivity and Semiconductors; Author: Professor Dave Explains;https://www.youtube.com/watch?v=5zz6LlDVRl0;License: Standard Youtube License