CONNECT F/SHIGLEY'S MECH.ENGR.DESIGN>I<
10th Edition
ISBN: 9781260058499
Author: BUDYNAS
Publisher: INTER MCG
expand_more
expand_more
format_list_bulleted
Question
Chapter 20, Problem 3P
To determine
The purpose of ASME Y14.5-2009 standard in drawing.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Draw three views, dimension using datum dimensioning
Answer the following questions.
1. What are the procedures used to calibrate platform scale?
2. What are the equipments used to calibrate platform scale?
4. Describe the dimensions: design quality and conformance quality.
Chapter 20 Solutions
CONNECT F/SHIGLEY'S MECH.ENGR.DESIGN>I<
Ch. 20 - In the traditional coordinate dimensioning system,...Ch. 20 - Prob. 2PCh. 20 - Prob. 3PCh. 20 - What is the term that refers to a feature which...Ch. 20 - What are the four geometric attributes that must...Ch. 20 - Prob. 6PCh. 20 - What are the three geometric characteristics that...Ch. 20 - What are the three geometric characteristics that...Ch. 20 - How is a basic dimension toleranced? (Select one.)...Ch. 20 - Prob. 10P
Ch. 20 - For the part shown, clearly identify each of the...Ch. 20 - Prob. 12PCh. 20 - For the part shown, answer the following questions...Ch. 20 - For the part shown, answer the following questions...Ch. 20 - Prob. 15PCh. 20 - Prob. 16PCh. 20 - Prob. 17PCh. 20 - Prob. 18PCh. 20 - Prob. 19PCh. 20 - A shaft diameter is dimensioned 20 0.2. According...Ch. 20 - Prob. 21PCh. 20 - Prob. 22PCh. 20 - Prob. 23PCh. 20 - Prob. 24PCh. 20 - Which geometric characteristics never reference...Ch. 20 - Answer the following questions regarding material...Ch. 20 - The drawing shown is of a mounting fixture to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Question 04: Discuss the importance of lubrication in journal bearings. How does lubrication effect the rotation of journal bearings?arrow_forwardRefer to the Ø.8740 ± .0005 dimension. D) What is the MMC,(Maximum material condition) ? ________________________________ E) What is the LMC,?(least material condition) _________________________________ Refer to the 1.914 dimension. Where is the tolerance specified ? _________________________________arrow_forwardIs the dimensioning correct?arrow_forward
- What is the important factor to consider when choosing the proper measuring tool to inspect a dimension?arrow_forwardWhat is calibration and why is it important?arrow_forwardUse BS 4500A:1970 to determine the dimensional tolerance on the critical diameters in Gear Sub- assembly. The following tolerance should be determined (the limits and fits at each interface will be provided by Canvas): i. Bush & Shaft: Critical Diameter is 35 mm; (H8/f7) ii. Housing & Bush: Critical Diameter is 45 mm; (H7/s6) iii. Gear & Shaft: Critical Diameter is 20 mm (for the Right Gear) (H7/k6)arrow_forward
- Two machines are currently in use in a process at a local manufacturing plant. The standards for this process are LSL = .400 and USL=.403. Machine One is currently producing with mean =.401 and a standard deviation= .0004. Machine Two is currently producing with mean = .4015 and a standard deviation = .0005. Which of the two machines is capable based on the capability index?arrow_forwardWhat is the estimated error of an EDM instruments having specified errors of ±( 8 mm + 5 ppm) in measuring distance 1439.24 m?arrow_forwardProblem 21.2. An inspector reports a total of 16 defects out of a total batch size of 200 parts. On closer examination, it is determined that three of these reported defects were in fact good pieces, while a total of seven defective units were undetected by the inspector. What is the inspector’s accuracy in this instance? Specifically, what are the values of p1 and p2? (b) What was the true fraction defect rate?arrow_forward
- I need help answering these 3 parts. 1. The size description of an object on the print can best be described as dimensioning. TRUE or FALSE 2. The amount that any one dimension can vary is referred to as the tolerance. TRUE OR FALSE 3. While the MMC of a feature is important, for certain design calculations, it is important to also understand the LMC. TRUE or FALSEarrow_forwarda) Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7 b) Using part reduction method redesign paper punch and calculate the assembly time using Boothroyddewhurst method.arrow_forwardDimension the object using datum dimensioningarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY