Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 21, Problem 2P
For problem 1, suppose you selected a speed of 145 sfpm and a feed of 0.015 in. per revolution. The workpiece is 4 in. in diameter.
- What is the input rpm?
- What is the MRR?
- What is the cutting time for a 6-in. cut?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A workpiece of 2000 mm length and 300 mm width was machined by a planning operation with the feed set at 0.3 mm/stroke. If the machine tool executes 10 double strokes/min,
What is the planning time for a single pass?
In face milling, assume that the Diameter of the cutter is 200 mm, the width of the block is 60 mm, and the length of the block is 344 mm, if the depth of cut is 3 mm, = 0.6 mm/min, and N = 100 rpm. The cutter has 12 inserts, and the workpiece material is bronze. Calculate the estimated power required, the cutting force, and the torque.
Assume that, in orthogonal cutting, the rake angle is 20 and the friction angle is 35 at thechip-tool interface. Determine the percentage change in chip thickness when the frictionangle is 50. Note that Merchant’s equation is more preferable.
Chapter 21 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 21 - Why has the metal-cutting process resisted...Ch. 21 - What variables must be considered in understanding...Ch. 21 - Which of the seven basic chip formation processes...Ch. 21 - How is feed related to speed in the machining...Ch. 21 - Before you select speed and feed for a machining...Ch. 21 - Milling has two feeds. What are they, and which...Ch. 21 - What is the fundamental mechanism of chip...Ch. 21 - What is the difference between oblique machining...Ch. 21 - What are the implications of Figure 21.13, given...Ch. 21 - Note that the units for the approximate equation...
Ch. 21 - For orthogonal machining, the cutting edge radius...Ch. 21 - How do the magnitude of the strain and strain rate...Ch. 21 - Why is titanium such a difficult metal to machine?...Ch. 21 - Explain why you get segmented or discontinuous...Ch. 21 - Why is metal cutting shear stress such an...Ch. 21 - Which of the three cutting forces in oblique...Ch. 21 - How is the energy in a machining process typically...Ch. 21 - Where does the energy consumed in metal cutting...Ch. 21 - What are two ways of estimating the primary...Ch. 21 - What are the three different ways to perform...Ch. 21 - Why does the cutting force Fc increase with...Ch. 21 - Why doesnt the cutting force Fc increase with...Ch. 21 - Prob. 23RQCh. 21 - How does the selection of the machining parameters...Ch. 21 - Suppose you had a machining operation (boring)...Ch. 21 - Make a sketch like that shown in Figure 21.1 with...Ch. 21 - Show how you would do near orthogonal machining in...Ch. 21 - Can you do orthogonal machining on a shaper or...Ch. 21 - What process and material combination would yield...Ch. 21 - What is meant by the statement that machining...Ch. 21 - Prob. 31RQCh. 21 - Figure 21.4 provides suggested cutting speeds and...Ch. 21 - For problem 1, suppose you selected a speed of 145...Ch. 21 - If the cutting forces is 1000 lb calculate the...Ch. 21 - Explain how you would estimate the cutting force...Ch. 21 - For a turning operation, you have selected a...Ch. 21 - For a slab milling operation using a...Ch. 21 - The power required to machine metal is related to...Ch. 21 - In order to drill a hole in the material described...Ch. 21 - Suppose you have the data in Table 21.A obtained...Ch. 21 - Calculate the horsepower that a process is going...Ch. 21 - Explain how you would estimate the cutting force...Ch. 21 - Derive equations for F and N using the circular...Ch. 21 - Prob. 14PCh. 21 - Prob. 15PCh. 21 - A manufacturing engineer needs an estimate of the...Ch. 21 - Using Figure 21.4 for input data, determine the...Ch. 21 - Estimate the horsepower needed to remove metal at...Ch. 21 - For a turning process, the horsepower required was...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A turbine is supplied with 0.6 m3/s of water from a 0.3 m diameter pipe; the discharge pipe has a 0.4 m diamete...
Fox and McDonald's Introduction to Fluid Mechanics
49. The maximum radius (R) a falling liquid drop can have without breaking apart is given by the equation , whe...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Modified coefficient of performance and power input for clean condition.
Introduction to Heat Transfer
The moment of the force F about an axis extending between A and C.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Find the time required for one full cut on a work piece of 350mm long and 20 mm in diameter. The cutting speed is 30 meters per minute and the feed is 0.5mm per revolution. Average. SHOW YOUR SOLUTION WITH DRAWINGSarrow_forwardIn orthogonal turning of a bar 100 mm diameter with a feed of 0.25 mm/rev., depth of cut = 4 mm, cutting velocity = 90 m/min. it is observed that the main cutting force is perpendicular to friction force acting at the chip tool interface and cutting force is 1500 N. find (i) rake angle (ii) normal force.arrow_forwardSuppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.arrow_forward
- In an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?arrow_forwardA motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate:arrow_forwardIn orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the main cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero Employing Merchant's theory, what is the ratio of friction force to normal force acting on the cutting tool?arrow_forward
- Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mmarrow_forwardA 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.arrow_forwardPlease give the correct solution A cylinder of 25 mm diameter and 100 mm length is turned with a tool, for which the relation VT0.25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, the number of tool regrinds required to produce 425 cylinders is?arrow_forward
- Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.arrow_forwardA 6.5 inch long, 0.5 inch diameter stainless steel rod is being reduced to 0.480 inches by turning on a lathe. The spindle rotates at 400 RPM and the tool is travelling at an axial speed of 8 inches/min. Calculate the cutting speed, feed, time, and material removal rate required.arrow_forwardNote: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License