Mastering Engineering with Pearson eText -- Standalone Access Card -- for Engineering Mechanics: Dynamics
14th Edition
ISBN: 9780133976687
Author: HIBBELER, Russell C.
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 21.3, Problem 25P
The large gear has a mass of 5 kg and a radius of gyration of kz = 75 mm. Gears B and C each have a mass of 200 g and a radius of gyration about the axis of their connecting shaft of 15 mm. If the gears are in mesh and C has an angular velocity of ωc = {15j} rad/s, determine the total angular momentum for the system of three gears about point A.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The 30-kg turbine disk has a centroidal radius of gyration of 175 mm and is rotating clockwise at a constant rate of 60 rpm when a small blade of weight 0.5 N at point A becomes loose and is thrown off. Neglecting friction, determine the change in the angular velocity of the turbine disk after it has rotated through (a ) 90°, (b ) 270°.
The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 32 kg and a radius of gyration k_O = 260 mm. The men A and B have a mass of 60 kg and 70 kg, respectively. Assume they do not move relative to the rope during the motion. Neglect the mass of the rope.
If two men A and B grab the suspended ropes and step off the ledges at the same time, determine the speed of man A in 4.2 s starting from rest.
vA= ???
If two men A and B grab the suspended ropes and step off the ledges at the same time, determine the speed of man B in 4.2 s starting from rest.
vB= ???
Chapter 21 Solutions
Mastering Engineering with Pearson eText -- Standalone Access Card -- for Engineering Mechanics: Dynamics
Ch. 21.1 - Show that the sum of the moments of inertia of a...Ch. 21.1 - Determine the moment of inertia of the cone with...Ch. 21.1 - Determine moment of inertia Iy of the solid formed...Ch. 21.1 - Determine the moments of inertia Ix and Iy of the...Ch. 21.1 - The density of the material is . Express the...Ch. 21.1 - Prob. 6PCh. 21.1 - Prob. 7PCh. 21.1 - Prob. 8PCh. 21.1 - The weight of the cone is 15 lb, the height is h =...Ch. 21.1 - The density of the material is .
Ch. 21.1 - Prob. 11PCh. 21.1 - Determine the moment of inertia Ixx of the...Ch. 21.1 - Determine the product of inertia Iyz of the...Ch. 21.1 - Prob. 14PCh. 21.1 - Prob. 15PCh. 21.1 - Determine the moment of inertia of the rod about...Ch. 21.1 - Prob. 17PCh. 21.1 - Prob. 18PCh. 21.1 - Prob. 19PCh. 21.1 - Prob. 20PCh. 21.1 - Prob. 21PCh. 21.3 - If a body contains no planes of symmetry, the...Ch. 21.3 - Prob. 23PCh. 21.3 - Prob. 24PCh. 21.3 - The large gear has a mass of 5 kg and a radius of...Ch. 21.3 - Prob. 26PCh. 21.3 - Prob. 27PCh. 21.3 - Prob. 28PCh. 21.3 - Prob. 29PCh. 21.3 - Prob. 30PCh. 21.3 - Prob. 31PCh. 21.3 - Prob. 32PCh. 21.3 - The 20-kg sphere rotates about the axle with a...Ch. 21.3 - The 200-kg satellite has its center of mass at...Ch. 21.3 - Prob. 35PCh. 21.3 - Prob. 36PCh. 21.3 - Prob. 37PCh. 21.3 - Prob. 38PCh. 21.3 - Prob. 39PCh. 21.3 - Prob. 40PCh. 21.4 - Derive the scalar form of the rotational equation...Ch. 21.4 - Prob. 42PCh. 21.4 - Prob. 43PCh. 21.4 - Prob. 44PCh. 21.4 - The disk has a weight of 15 lb. Neglect the weight...Ch. 21.4 - Prob. 46PCh. 21.4 - Prob. 47PCh. 21.4 - Prob. 48PCh. 21.4 - Prob. 49PCh. 21.4 - Prob. 50PCh. 21.4 - Prob. 51PCh. 21.4 - The 5-kg circular disk is mounted off center on a...Ch. 21.4 - Prob. 53PCh. 21.4 - Prob. 54PCh. 21.4 - Prob. 55PCh. 21.4 - The 4-kg slender rod AB is pinned at A and held at...Ch. 21.4 - Prob. 57PCh. 21.4 - Prob. 58PCh. 21.4 - Prob. 59PCh. 21.4 - Show that the angular velocity of a body, in terms...Ch. 21.4 - Prob. 61PCh. 21.6 - The gyroscope consists of a uniform 450-g disk D...Ch. 21.6 - Prob. 63PCh. 21.6 - Prob. 64PCh. 21.6 - Prob. 65PCh. 21.6 - When viewed from the front of the airplane, the...Ch. 21.6 - Prob. 67PCh. 21.6 - Prob. 68PCh. 21.6 - Prob. 69PCh. 21.6 - Prob. 70PCh. 21.6 - Prob. 71PCh. 21.6 - Prob. 72PCh. 21.6 - Prob. 73PCh. 21.6 - Prob. 74PCh. 21.6 - Prob. 75PCh. 21.6 - Prob. 76PCh. 21.6 - Prob. 77PCh. 21.6 - Prob. 78P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The spool has a mass of 20 kg and a radius of gyration of kO = 160 mm If the 15-kg block A is released from rest, determine the velocity of the block when it descends 850 mm .arrow_forwardEach of the two links has a mass of 2 kg and a centroidal radius of gyration of 60mm. The slider at B has a mass of 3 kg and moves freely in the vertical guide. The springhas a stiffness of 6 kN/m. If a constant torque M = 20 N∙m is applied to link OA throughits shaft at O starting from the rest position at θ = 45°, determine the angular velocity ofOA when θ = 0.arrow_forwardThe assembly weighs 10 lblb and has a radius of gyration kGkGk_G = 0.60 ftft about its center of mass GG. The kinetic energy of the assembly is 25 ft⋅lbft⋅lb when it is in the position shown. (Figure 1) If it rolls counterclockwise on the surface without slipping, determine its linear momentum at this instant.arrow_forward
- The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2arrow_forwardThe 10-kg uniform slender rod is suspended at rest when the force of F = 150 N is applied to its end. Determine the angular velocity of the rod when it has rotated 180° clockwise from the position shown. The force is always perpendicular to the rod.arrow_forwardThe 31-kg reel is mounted on the 16-kg cart. Part A: If the cable wrapped around the inner hub of the reel is subjected to a force of P=50N, determine the velocity of the cart when t = 4.2 s. The radius of gyration of the reel about its center of mass O is kO=250mm. Neglect the size of the small wheels. Part B: Determine the angular velocity of the reel when t = 4.2 s.arrow_forward
- In the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.arrow_forwardAt the instant shown, the 200-lb bar rotates clockwise at 4 rad/s. The spring attached to its endalways remains vertical due to the roller guide at C. If the spring has an unstretched length of 2ft and a stiffness of k = 9 lb/ft, determine the angular velocity of the bar the instant it has rotated 39° clockwise.arrow_forwardGears A and B each have a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A torque M with constant magnitude of 10 N.m to gear C. Determine a) the number of revolutions of gear C that is required for its angular velocity to increase from 100 to 450 rpm. b) the corresponding tangential force acting on gear A Please include the free body diagram if necessary.arrow_forward
- The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheelsarrow_forwardThe 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.11. The radius of gyration about the mass center is kG = 0.26 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest.arrow_forwardIn the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License