Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 22, Problem 28QLP
Titanium-nitride coatings on tools reduce the coefficient of friction at the tool–chip interface. What is the significance of this property?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
2 1.4 1 The Taylor tool-life equation is directly applicable to flank wear. Explain whether or not it can be used to model tool life if other forms of wear are dominant.
Discuss the effects of cutting speed, feed rate, and depth of cut on the tool wear rate during a turning operation.
How does each parameter influence the surface finish of the workpiece?
Provide a detailed explanation based on the principles of metal cutting mechanics.
2 2.46 Describe in detail your thoughts regarding the technical and economic factors involved in tool-material selection.
Chapter 22 Solutions
Manufacturing Engineering & Technology
Ch. 22 - What are the major properties required of...Ch. 22 - What is the composition of a typical carbide tool?Ch. 22 - Why were cutting-tool inserts developed?Ch. 22 - Why are some tools coated? What are the common...Ch. 22 - Explain the applications and limitations of...Ch. 22 - List the major functions of cutting fluids.Ch. 22 - Why is toughness important for cutting-tool...Ch. 22 - Is the elastic modulus important for cutting-tool...Ch. 22 - Explain how cutting fluids penetrate the toolchip...Ch. 22 - List the methods by which cutting fluids are...
Ch. 22 - Describe the advantages and limitations of (a)...Ch. 22 - What is a cermet? What are its advantages?Ch. 22 - Explain the difference between M-series and...Ch. 22 - Why is cBN generally preferred over diamond for...Ch. 22 - What are the advantages to dry machining?Ch. 22 - Explain why so many different types of...Ch. 22 - Which tool-material properties are suitable for...Ch. 22 - Describe the reasons for and advantages of coating...Ch. 22 - Make a list of the alloying elements used in...Ch. 22 - As stated in Section 22.1, tool materials can have...Ch. 22 - Explain the economic impact of the trend shown in...Ch. 22 - Why does temperature have such an important effect...Ch. 22 - Ceramic and cermet cutting tools have certain...Ch. 22 - What precautions would you take in machining with...Ch. 22 - Can cutting fluids have any adverse effects in...Ch. 22 - Describe the trends you observe in Table 22.2.Ch. 22 - Why are chemical stability and inertness important...Ch. 22 - Titanium-nitride coatings on tools reduce the...Ch. 22 - Describe the necessary conditions for optimal...Ch. 22 - Negative rake angles generally are preferred for...Ch. 22 - Do you think that there is a relationship between...Ch. 22 - Make a survey of the technical literature, and...Ch. 22 - In Table 22.1, the last two properties listed...Ch. 22 - It has been stated that titanium-nitride coatings...Ch. 22 - Note in Fig. 22.1 that all tool materials,...Ch. 22 - Referring to Table 22.1, state which tool...Ch. 22 - Which of the properties listed in Table 22.1 is,...Ch. 22 - If a drill bit is intended only for woodworking...Ch. 22 - What are the consequences of a coating on a tool...Ch. 22 - Discuss the relative advantages and limitations of...Ch. 22 - Emulsion cutting fluids typically consist of 95%...Ch. 22 - List and explain the considerations involved in...Ch. 22 - Review the contents of Table 22.1. Plot several...Ch. 22 - Obtain data on the thermal properties of various...Ch. 22 - The first column in Table 22.2 shows 10 properties...Ch. 22 - Describe in detail your thoughts regarding the...Ch. 22 - One of the principal concerns with coolants is...Ch. 22 - How would you go about measuring the effectiveness...Ch. 22 - There are several types of cutting-tool materials...Ch. 22 - Assume that you are in charge of a laboratory for...Ch. 22 - Tool life could be greatly increased if an...Ch. 22 - List the concerns you would have if you needed to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a matrix of 0.1 mm (0.004 in) diameter holes in a plate of 3.2 mm (0.125 in) thick hardened tool steel. The matrix is rectangular, 75 by 125 mm (3.0 by 5.0 in) with the separation between holes in each direction = 1.6 mm ( 0.0625 in).arrow_forward11. Estimate the machining time required to rough turn a 0.5 m long annealed copper alloyRound bar from a 60 mm diameter to a 58 mm diameter, using a high-speed tool. Estimate the time required for an uncoated carbide tool.arrow_forwarda rod is to be manufactured using turning operations and is made of Nickel alloy. The rod is 80 mm in length and 15 mm in diameter. The final required diameter is 10 mm and the spindle rotates at N = 500 rpm while the tool axial speed is 100 mm/ min. Calculate material removal rate, cutting speed, cutting time, the power dissipated, and cutting force.arrow_forward
- In an orthogonal cutting test, the cutting force and thrust force were observed to be 1000N and 500 N respectively. If the rake angle of tool is zero, What is the coefficient of friction in chip-tool interface ?arrow_forwardIn machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour and 40 minutes, at a spindle speed of 25 m/min. Calculate the tool life if it has to be operated at a speed of 30% higher than the initial cutting speed. Also calculate the cutting speed if the tool is required to have a life of 2 hours and 45 minutes. Assume Taylor’s exponent value n is 0.28.arrow_forwardPlease give the correct solution A cylinder of 25 mm diameter and 100 mm length is turned with a tool, for which the relation VT0.25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, the number of tool regrinds required to produce 425 cylinders is?arrow_forward
- A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel cutter travelling at 180 mm/min. The spindle rotates at 450 rpm and lathe is equipped with a 10 kW motor, operating at a mechanical efficiency of 92%. The final diameter of the magnesium alloy bar is 59,5 mm. Indicate with a sketch the recommend size and location of the following tool angles: back rake, side rake, end relief, side relief and side and end cutting edge. Calculate the cutting time for the machining process.Calculate the required cutting force.arrow_forward7. What is the manufacturing process of lathe bed? Which material will be suitable for the product? Justify your answer.arrow_forwardDraw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if ,cutting force = 80 kN, resultant of forces =100kN, friction force=75kN, rake angle =20° undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mmarrow_forward
- For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a through-hole in the shape of the letter L in a 12.5 mm (0.5 in) thick plate of glass. The size of the "L" is 25 by 15 mm (1.0 by 0.6 in) and the width of the hole is 3 mm (1/8 in).arrow_forward2 2 . 16 Explain why so many different types of cutting-tool materials have been developed over the years. Why are they still being developed further?arrow_forwardAn orthogonal cutting operation is being carried out in which to=0.2 mm, V=2m/s, a=7.5o, and the width of cut=5 mm. It is observed that tc=0.25mm, Fc=400N, and Ft=300N. Calculate the percentage of the total energy that is dissipated in friction at the tool-chip interface. A) 22% B) 50% C) 70% D)None of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY