Manufacturing Engineering And Technology
7th Edition
ISBN: 9789810694067
Author: Stephen R. Schmid (author) Serope Kalpakjian (author)
Publisher: Pearson Education Orphans
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 24, Problem 39QTP
Show that the distance lc in slab milling is approximately equal to
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In face milling, assume that the Diameter of the cutter is 200 mm, the width of the block is 60 mm, and the length of the block is 344 mm, if the depth of cut is 3 mm, = 0.6 mm/min, and N = 100 rpm. The cutter has 12 inserts, and the workpiece material is bronze. Calculate the estimated power required, the cutting force, and the torque.
Calculate the spindle speed for a Lathe Machine, if the cutting speed for a mild steel material workpiece is 34 m/min and the diameter of the cylindrical workpiece is 46 mm.
A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm in length and 50 mm in width, using a felicoidal bur with a diameter of 75 mm, with 10 teeth. If the feed per tooth is 0.2mm, and the cutting speed is 0.75 m / s, how would you determine the speed of metal removal to remove 6 mm from the surface of this piece?
Chapter 24 Solutions
Manufacturing Engineering And Technology
Ch. 24 - Explain why milling is such a versatile machining...Ch. 24 - Describe a milling machine. How is it different...Ch. 24 - Describe the different types of cutters used in...Ch. 24 - Define the following: face milling, peripheral...Ch. 24 - Can threads be machined on a mill? Explain.Ch. 24 - What is the difference between feed and feed per...Ch. 24 - Explain the relative characteristics of climb...Ch. 24 - Describe the geometric features of a broach and...Ch. 24 - What is a pull broach? A push broach?Ch. 24 - Why is sawing a commonly used process? Why do some...
Ch. 24 - What advantages do bed-type milling machines have...Ch. 24 - Explain why the axis of a hob is tilted with...Ch. 24 - What is a shell mill? Why is it used?Ch. 24 - Why is it difficult to saw thin sheet metals?Ch. 24 - Of the processes depicted in Fig. 24.2, which is...Ch. 24 - Describe the tool motion during gear shaping.Ch. 24 - When is filing necessary?Ch. 24 - Would you consider the machining processes...Ch. 24 - Why is end milling such an important versatile...Ch. 24 - List and explain factors that contribute to poor...Ch. 24 - Explain why broaching crankshaft bearings is an...Ch. 24 - Several guidelines are presented in this chapter...Ch. 24 - What are the advantages of helical teeth over...Ch. 24 - Explain why hacksaws are not as productive as band...Ch. 24 - What similarities and differences are there in...Ch. 24 - Why do machined gears have to be subjected to...Ch. 24 - How would you reduce the surface roughness shown...Ch. 24 - Why are machines such as the one shown in Fig....Ch. 24 - Comment on your observations concerning the...Ch. 24 - Explain how contour cutting could be started in a...Ch. 24 - Prob. 32QLPCh. 24 - Describe the parts and conditions under which...Ch. 24 - Explain the reason that it is difficult to use...Ch. 24 - Would you recommend broaching a keyway on a gear...Ch. 24 - Prob. 37QTPCh. 24 - A slab-milling operation is being performed at a...Ch. 24 - Show that the distance lc in slab milling is...Ch. 24 - Prob. 40QTPCh. 24 - Calculate the chip depth of cut, tc, and the...Ch. 24 - Estimate the time required to face mill a...Ch. 24 - A 12-in.-long, 1-in.-thick plate is being cut on a...Ch. 24 - A single-thread hob is used to cut 40 teeth on a...Ch. 24 - Assume that m the face-milling operation shown in...Ch. 24 - A slab-milling operation will take place on a part...Ch. 24 - Prob. 47QTPCh. 24 - In describing the broaching operations and the...Ch. 24 - The parts shown in Fig. 24.1 are to be machined...Ch. 24 - Would you prefer to machine the part in Fig. 24....Ch. 24 - Prob. 51SDPCh. 24 - Suggest methods whereby milling cutters of various...Ch. 24 - Prepare a comprehensive table of the process...Ch. 24 - Prob. 55SDPCh. 24 - Make a list of all the processes that can be used...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.arrow_forwardSuppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.arrow_forwardIn orthogonal turning of a bar 100 mm diameter with a feed of 0.25 mm/rev., depth of cut = 4 mm, cutting velocity = 90 m/min. it is observed that the main cutting force is perpendicular to friction force acting at the chip tool interface and cutting force is 1500 N. find (i) rake angle (ii) normal force.arrow_forward
- A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm, and depth of cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?arrow_forwardEstimate the machining time that will be required to finish a vertical flat surface of length 100 mm and depth 20 mm by an end mill cutter of 32 mm diameter and 60 mm length in a milling machine. Assume cutting speed of 30 m/min and feed of 0.12 mm/tooth. Let over run distance equal to approach distance.arrow_forwardFind the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.arrow_forward
- In an orthogonal machining with a tool of 9 degree orthogonal rake angle, the uncut chip thickness is 0.2mm. The chip thickness fluctuates between 0.25 mm and 0.4 mm. The ratio of the maximum shear angle to the minimum shear angle during machining isarrow_forwardAssuming that the coefficient of friction is 0.25, calculate the maximum depth of cut forturning a hard aluminium alloy on a 15-kW lathe (with a mechanical efficieny of 80%) at awidth of cut of 6 mm, rake angle of 0˚, and a cutting speed of 90 m/min, shear strength of 150 MPa.arrow_forwardWhat is difference in turning and boring processes? Explain the difference if any in the equations for cutting speed, material removal rate, and machining timearrow_forward
- A slab milling operation is performed on the top surface of a tool-steel workpiece 450 mm long by 7.5 cm wide. The helical milling cutter, which has an 80 mm diameter and seven teeth, is set up to overhang the width of the part on both sides. Cutting speed is 4000 mm/min, feed is 0.015 cm/tooth, and depth of cut = 0.60 cm. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.05 m is added at the beginning of the pass, and an overtravel distance at the end of the pass equal to the cutter radius plus 0.0115 cm, what is the duration of the feed motionarrow_forwardA slab-milling operation is being carried out on a block on a 200 mm-long, 150 mm-wide annealed mild steel block at a feed f=0.20mm/tooth and depth of cut d=2.5mm. The cutter is D=45 mm in dimater, has 20 straight teeth, rotates at N=110rpm and by the definition, is wider than the block to be machined. Calculate;1. Material removal2. Estimate the power and torque required for this operation3. Calculate the cutting timearrow_forwardDiscuss the impact of current and voltage on machining characteristics in EDM in detailarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License