Concept explainers
a.
Instructions in Vole machine language:
Computer can understand only machine language, so the instruction must be given in vole machine language. It is an encoded language. The instructions are encoded by using total 16-bits that is also represented by hexadecimal digits. Instructions in vole machine consist of op-code and operation field of the register. First 4 bits are called the op-code and operation field has last 12 bits.
b.
Instructions in Vole machine language:
Computer can understand only machine language, so the instruction must be given in vole machine language. It is an encoded language. The instructions are encoded by using total 16-bits that is also represented by hexadecimal digits. Instructions in vole machine consist of op-code and operation field of the register. First 4 bits are called the op-code and operation field has last 12 bits.
c.
Instructions in Vole machine language:
Computer can understand only machine language, so the instruction must be given in vole machine language. It is an encoded language. The instructions are encoded by using total 16-bits that is also represented by hexadecimal digits. Instructions in vole machine consist of op-code and operation field of the register. First 4 bits are called the op-code and operation field has last 12 bits.
Want to see the full answer?
Check out a sample textbook solutionChapter 2 Solutions
Computer Science: An Overview (12th Edition)
- If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?arrow_forwardThe time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?arrow_forwardA set of ten packed BCD numbers is stored in the memory location starting at 3050H. i. Write a program with a subroutine to add these numbers in BCD. If a carry is generated, save it in register B, and adjust it for BCD. The final sum will be less than 9999sCD. ii. Write a second subroutine to unpack the BCD sum stored in registers A and B, and store them in the memory locations starting at 3070H. The most significant digit (BCD4) should be stored at 3070H and the least significant digit (BCD) at 3073H.arrow_forward
- if a program has 471 bytes and will be loaded into page frames of 100 bytes each, and the instruction is to be used at bytr 132, answer the following question: how many pages are needed to do the entire job?arrow_forward26. Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RETarrow_forwardQ1- Write a program in assembly language for the 8085 microprocessor to receive 10 bytes of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When you receive each byte of the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception (start bits), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit). The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes The solution must be integrated and include the calculation of the baudrate delay time Of+CD!HID+[00 Yes SIDATA Read SID Start Bit? Wait for Half-Bit Time Set up Bit Counter Wait Bit Time Read SID Save Bit Decrement Bit Counter All Bits Received? Add Bit to Previous Bits Go Back to Get Next Bit Return IMUNIarrow_forward
- y of H Q. For the given circuit, which of the following is correct? E OF RAM 256 X 4 A. The number 5 is being written to the memory at address location 203. B. The chip has not been enabled, since the EN terminal is 0; therefore, nothing will be written to the chip and the output is tri- 1 A0 1 A1 O A2 O A3 1 A4 A 255 O A5 1 A6 1 A7 71 QO stated. O DO 1 D1 O D2 1 D3 C. Decimal 10 is being written into memory location 211. D. The read/write line is LOW; therefore, WRITE decimal 5 is being stored at memory O R/W O CS READ EN location 211. Data inputs Address inputs DDDD Data outputsarrow_forwardConsider the instruction “slt $t3, $s2, $s1” . What is the rd field in binary using the required number of bits for representing the rd field in the machine language Instruction or write DNE if it does not exist?arrow_forwardQ2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay timearrow_forward
- Assume that the instruction pointer, EIP, contains 9810 and the assembly language representation of the instruction in memory at address 9810 is JAE 131. If the flags are currently CF=1, ZF=0 and SF=0 what is the value of the EIP after the instruction executes? The answer 102 is not correct so what is the correct answer?arrow_forward2- Write a program in assembly language for the 8085 microprocessor to receive 10 bytes of data via the SID and store it at the memory address (3000h) using a baud rate of 1200. And two high pulses must be sent before each byte (start bits) and one low pulse after each byte (end bits). You can use this flowchart, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes No CDD CHHICE 10 Yes SIDATA Read SID Start Bit? Wait for Half-Bit Time Set up Bit Counter Wait Bit Time Read SID Save Bit Decrement Bit Counter All Bits Received? Add Bit to Previous Bits Go Back to Get Next Bit Returnarrow_forwardWrite a 8085 assembly language program which will be interrupted by giving a rising signal at RST 7.5 input. The program will copy 512 bytes of data which is stored at memory location starting from 1235H to memory location starting from 9999H. The interrupt signal should, however, be able to introduce a delay of 1 sec. Once the delay finishes, it should then move to the main program. The main program for moving the data is in a loop that reruns the same task repeatedly.arrow_forward
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage LearningPrinciples of Information Systems (MindTap Course...Computer ScienceISBN:9781285867168Author:Ralph Stair, George ReynoldsPublisher:Cengage Learning