Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 25, Problem 30RQ
Suppose you specified a drilling feed rate that was too large. What kinds of problems do you think this might cause? See Figure 25.6 and Table 25.4 for help.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Calculate the RPM for drilling at 200 SFM and feed rate (in/min) for a chip load of .010 (in/rev).
Material is aluminum
Sketch a radial drilling machine? Explain the working, advantages and disadvantages of a radial drilling machine
What are the advantages of directional drilling?
Chapter 25 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 25 - What functions are performed by the flutes on a...Ch. 25 - What determines the rake angle of a drill? See...Ch. 25 - Basically, what determines what helix angle a...Ch. 25 - When a large-diameter hole is to be drilled, why...Ch. 25 - Equation 25.4 for the MRR for drilling can be...Ch. 25 - Are the recommended surface speeds for spade...Ch. 25 - What can happen when an improperly ground drill is...Ch. 25 - Why are many drilled holes oversize with respect...Ch. 25 - What are the two primary functions of a...Ch. 25 - What is the function of the margins on a twist...
Ch. 25 - What factors tend to cause a drill to drift off...Ch. 25 - The drill shown in Figure 25.13 has coolant...Ch. 25 - Prob. 13RQCh. 25 - Why do cutting fluids for drilling usually have...Ch. 25 - How does a gang-drilling machine differ from a...Ch. 25 - Prob. 16RQCh. 25 - How does the thrust force vary with feed? Why?Ch. 25 - Holding the workpiece by hand when drilling is not...Ch. 25 - Prob. 19RQCh. 25 - In terms of thrust, what is unusual about the...Ch. 25 - Prob. 21RQCh. 25 - Prob. 22RQCh. 25 - What are the primary purposes of reaming?Ch. 25 - What are the advantages of shell reamers?Ch. 25 - A drill that operated satisfactorily for drilling...Ch. 25 - What precautionary procedures should be used when...Ch. 25 - What is the advantage of a spade drill? Is it...Ch. 25 - Prob. 28RQCh. 25 - Why does drill feed increase with drill size?Ch. 25 - Suppose you specified a drilling feed rate that...Ch. 25 - Suppose you wanted to drill a 1.5-in.-diameter...Ch. 25 - How much time will be required to drill the hole...Ch. 25 - What is the metal removal rate when a...Ch. 25 - If the specific horsepower for the steel in...Ch. 25 - If the specific power of an AISI 1020 steel of...Ch. 25 - Prob. 6PCh. 25 - Assume that you are drilling eight holes, equally...Ch. 25 - What machining difficulties should this process...Ch. 25 - Why were the distances between the holes too...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the normal stress in each member of the truss structure. All joints are ball joint, and the material ...
Introduction To Finite Element Analysis And Design
3.45 For the concrete structure shown, determine the magnitude, direction, and sense of the resultant force. De...
Applied Statics and Strength of Materials (6th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
A loading causes the mamber to deform into the dashed shape. Explain how to determine the normal strains CD and...
Mechanics of Materials (10th Edition)
Consider refrigerant R-134a flowing in a smooth, horizontal, tube of wall thickness 2 mm. The refrigerant is at...
Fundamentals of Heat and Mass Transfer
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Briefly contrast the speed and feed differences between drilling and reaming operations.arrow_forwardA o 20 mm through hole is to be drilled in a 30 mm thick plate using a double fluted, 120° lip angle drill The drill tip is at a distance of 3 mm from the plate surface when cutting is started and an over travel of 2 mm is recommended as a margin to ensure drilling through the full thickness of the plate. If the drill rotates at 500 rev/min and the feed per tooth is 0.01 mm,find the machining time of the operation.arrow_forwardA drilling operation is to be performed with a 12.7 mm diameter twist drill in a steelwork part. The hole is a blind hole at a depth of 60 mm and the point angle is 118 ̊. The cutting speed is 25 m/min and the feed is 0.3 mm/rev. determine The cutting time to complete the drilling operation,arrow_forward
- Calculate the machining time required for making 60 holes on an MS plate of 80 mm thickness with a drillbit of diameter 20 mm with a cutting speed V= 40 m/min, the feed f = 0.2 mm/rev. (Assume approach length,A and over run O as 2mm and point angle as 110o). Calculate material removal rate.arrow_forwardIn an orthogonal cutting operation an 8 mm deep groove is to be turned on a 50 mm diameter steel bar. Spindle speed is 300 rpm and a feed rate of 0.25 mm/rev is given to the tool. Produced chips have a width of 2 mm. Calculate the material removal rate at the beginning and at the end of the cut. Can u help me please?arrow_forwardThe cutting speed in in/min of a 12 mm drill operating at 600 rpm is nearly equal toarrow_forward
- How is twist drill manufactured? Explain with neat sketches wherever applicable.arrow_forward5.) Calculate the machining time required to reduce from 60mm diameter shaft to 50mm diameter, for a length of 1500mm with depth of cut 2mm for rough cut and 1mm for finish cut. Cutting speed and feed may be assumed as 30m/min and 0.5mm/rev respectively.arrow_forwardwhat are the disadvantages or restriction(limitation) for a automated drilling processarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License