Fundamentals of Physics, Volume 1, Chapter 1-20
10th Edition
ISBN: 9781118233764
Author: David Halliday
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 26, Problem 2Q
Figure 26-16 shows cross sections through three wires of identical length and material; the sides are given in millimeters. Rank the wires according to their resistance (measured end to end along each wire’s length), greatest first.
Figure 26-16 Question 2.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
2 Figure 26-16 shows cross sections through three wires of identi-
cal length and material; the sides are given in millimeters. Rank the
wires according to their resistance (measured end to end along
each wire's length), greatest first.
6.
(a)
(6)
(c)
Figure 26-16 Question 2.
We have a copper conductor, length l = 1m and circular section of diameter d = 4mm a) Calculate the resistance of the conductor between its ends. b) If a current of 1 amp flows through said conductor: I) Calculate the drag speed of the electrons. II) calculate the number of electrons per second that cross the conductor section. Data: resistivity of copper PCu = 1.7 × 10-8 -8 ampere m: numerical density of charge carriers [nCu] = 8.5 × 1028 atoms m-3: resistivity of aluminum p Al = 2.8 × 10-8 ampere m elemental load = 1.6x10-19 C
A rod of semiconducting material of length L 2 m and cross-sectional area A- 4.5 mm? lies along the x-axis between z0 and a- L The material obeys Ohm's law, and its resistivity
varies along the rod according to p= p(1
where po4x 10 n m. The end of the rod at z=0 is at a potential V- 15 V greater than the end at z-L
L2
A) What is the total resistance, in units of fn, of the rod?
Chapter 26 Solutions
Fundamentals of Physics, Volume 1, Chapter 1-20
Ch. 26 - Figure 26-15 shows cross sections through three...Ch. 26 - Figure 26-16 shows cross sections through three...Ch. 26 - Figure 26-17 shows a rectangular solid conductor...Ch. 26 - Figure 26-18 shows plots of the current i through...Ch. 26 - Figure 26-19 shows four situations in which...Ch. 26 - In Fig. 26-20, a wire that carries a current...Ch. 26 - Figure 26-21 gives the electric potential Vx...Ch. 26 - The following table give the lengths of three...Ch. 26 - Prob. 9QCh. 26 - Three wires, of the same diameter, are connected...
Ch. 26 - Figure 26-23 gives, for three wires of radius R,...Ch. 26 - During the 4.0 min a 5.0 A current is set up in a...Ch. 26 - An isolated conducting sphere has a 10 cm radius....Ch. 26 - A charged belt, 50 cm wide, travels at 30 m/s...Ch. 26 - The United States National Electric Code, which...Ch. 26 - SSM WWW A beam contains 2.0 108 doubly charged...Ch. 26 - A certain cylindrical wire carries current. We...Ch. 26 - A fuse in an electric circuit is a wire that is...Ch. 26 - Prob. 8PCh. 26 - The magnitude Jr of the current density in a...Ch. 26 - The magnitude J of the current density in a...Ch. 26 - What is the current in a wire of radius R = 3.40...Ch. 26 - Near Earth, the density of protons in the solar...Ch. 26 - Prob. 13PCh. 26 - A human being can be electrocuted if a current as...Ch. 26 - SSM A coil is formed by winding 250 turns of...Ch. 26 - Copper and aluminium are being considered for a...Ch. 26 - Prob. 17PCh. 26 - A wire 4.00 m long and 6.00 mm in diameter has a...Ch. 26 - SSM What is the resistivity of a wire of 1.0 mm...Ch. 26 - Prob. 20PCh. 26 - ILW A common flashlight bulb is rated at 0.30 A...Ch. 26 - Kiting during a storm. The legend that Benjamin...Ch. 26 - Prob. 23PCh. 26 - GO Figure 26-25a gives the magnitude Ex of the...Ch. 26 - SSM ILW A wire with a resistance of 6.0 is drawn...Ch. 26 - In Fig. 26-26a. a 9.00 V battery is connected to a...Ch. 26 - SSM WWW Two conductors are made of the same...Ch. 26 - GO Figure 26-27 gives the electric potential Vx...Ch. 26 - Prob. 29PCh. 26 - Prob. 30PCh. 26 - Prob. 31PCh. 26 - Prob. 32PCh. 26 - Prob. 33PCh. 26 - GO Figure 26-29 shows wire section 1 of diameter...Ch. 26 - GO In Fig. 26-30, current is set up through a...Ch. 26 - GO Swimming during a storm. Figure 26-31 shows a...Ch. 26 - Prob. 37PCh. 26 - In Fig. 26-32a, a 20 resistor is connected to a...Ch. 26 - A certain brand of hot-dog cooker works by...Ch. 26 - Thermal energy is produced in a resistor at a rate...Ch. 26 - SSM A 1220 V potential difference is applied to a...Ch. 26 - In Fig. 26-33, a battery of potential difference V...Ch. 26 - ILW An unknown resistor is connected between the...Ch. 26 - A student kept his 6.0 V, 7.0 W radio turned on at...Ch. 26 - SSM ILW A 1250 W radiant heater is constructed to...Ch. 26 - A copper wire of cross-sectional area 2.00 106 m2...Ch. 26 - A heating element is made by maintaining a...Ch. 26 - Exploding shoes. The rain-soaked shoes of a person...Ch. 26 - A 100 W lightbulb is plugged into a standard 120 V...Ch. 26 - GO The current through the battery and resistors 1...Ch. 26 - GO SSM WWW Wire C and wire D are made from...Ch. 26 - GO The current-density magnitude in a certain...Ch. 26 - A 120 V potential difference is applied to a space...Ch. 26 - Go Figure 26-36a shows a rod of resistive...Ch. 26 - SSM A Nichrome heater dissipates 500 W when the...Ch. 26 - Prob. 56PCh. 26 - An 18.0 W device has 9.00 V across it. How much...Ch. 26 - An aluminum rod with a square cross section is 1.3...Ch. 26 - A cylindrical metal rod is 1.60 m long and 5.50 mm...Ch. 26 - The chocolate crumb mystery. This story begins...Ch. 26 - SSM A steady beam of alpha particles q = 2e...Ch. 26 - A resistor with a potential difference of 200 V...Ch. 26 - A 2.0 kW heater element from a dryer has a length...Ch. 26 - cylindrical resistor of radius 5.0 mm and length...Ch. 26 - A potential difference V is applied to a wire of...Ch. 26 - The headlights of a moving car require about 10 A...Ch. 26 - A 500 W heating unit is designed to operate with...Ch. 26 - The copper windings of a motor have a resistance...Ch. 26 - How much electrical energy is transferred to...Ch. 26 - A caterpillar of length 4.0 cm crawls in the...Ch. 26 - Prob. 71PCh. 26 - A steel trolley-car rail has a cross-sectional...Ch. 26 - A coil of current-carrying Nichrome wire is...Ch. 26 - Prob. 74PCh. 26 - A certain x-ray tube operates at a current of 7.00...Ch. 26 - A current is established in a gas discharge tube...Ch. 26 - In Fig.26-37, a resistance coil wired to an...Ch. 26 - An insulating belt moves at speed 30 m/s and has a...Ch. 26 - In a hypothetical fusion research lab, high...Ch. 26 - When a metal rod is heated, not only its...Ch. 26 - A beam of 16 MeV deuterons from a cyclotron...Ch. 26 - A linear accelerator produces a pulsed beam of...Ch. 26 - An electric immersion heater normally takes 100...Ch. 26 - A 400 W immersion heater is placed in a pot...Ch. 26 - A 30 F capacitor is connected across a programmed...
Additional Science Textbook Solutions
Find more solutions based on key concepts
23. How many significant figures are there in the following values?
a. 0.05 × 10-4 b. 0.00340
c. 7.2 × 104 ...
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
An aluminum calorimeter with a mass of 100 g contains 250 g of water. The calorimeter and water are in thermal ...
Physics for Scientists and Engineers, Technology Update (No access codes included)
Calculate the average volume per molecule for an ideal gas at room temperature and atmospheric pressure. Then t...
An Introduction to Thermal Physics
How is the charging time for a capacitor correlated with the initial current? That is, if the initial current i...
Matter and Interactions
In standard household wiring, parallel wires about 1 cm apart carry currents of about 15 A. Whats the force per...
Essential University Physics: Volume 2 (3rd Edition)
The process in which mass of an isotopes do not change is to be identified.
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- Two conductors are made of the same material and have the same length. Con- ductor A is a solid wire of diameter 1.0 mm. Conductor B is a hollow tube of outside diameter 2.0 mm and inside diameter 1.0 mm. What is the resistance ratio RA/RB, mea- sured between their ends?arrow_forwardWire C and wire D are made from different materials materials and have length L_{C} = L_{D} = 1m The resistivity and diameter of wire C are 2 * 10 ^ - 6 * Omega*m and 1.00 mm, and those of wire D are 1 * 10 ^ - 6 * Omega*m and 0.50 mm. The wires are joined as shown in Fig. 26-35, and a current of 2.0 A is set up in them. What is the electric potential difference be- tween (a) points 1 and 2 and (b) points 2 and 3? What is the rate at which energy is dissipated between (c) points 1 and 2 and (d) points 2 and 3?arrow_forwardAn independent and constant current source is supplying 0.6 ampere to a uniform copper conductor with length 40 mm, inner radius 7 mm, and outer diameter 20 mm. If the resistivity and the electron concentration of the conductor are 2.4 x 10-8 ohm-meter and 6.4 x 1024 electrons per cubic meter, respectively: a. The drift velocity in the conductor; b. The voltage across the conductor;arrow_forward
- A rod of semiconducting material of length L2 m and cross-sectional area A - 4.5 mm lies along the x-axis between z0 and z - L The material obeys Ohm's law, and its resistivity varies along the rod according to p- p(1- where p-4x 10 n-m. The end of the rod at a- 0 is at a potential V, - 15 V greater than the end at z- L B) What is the current, in units.of miliamperes in the rod? Answer:arrow_forward1 Figure 26-15 shows cross sections through three long conduc- tors of the same length and material, with square cross sections of edge lengths as shown. Conductor B fits snugly within conductor A, and conductor C fits snugly within conductor B. Rank the fol- lowing according to their end-to-end resistances, greatest first: the individual conductors and the combinations of A + B (B inside A), B+ C (Cinside B), and A + B + C(B inside A inside C). Figure 26-15 Question 1.arrow_forwardA straight, cylindrical wire lying along the x axis has a length of 0.5 m and a diameter of0.2 mm. It is made of a material described by Ohm’s law with a resistivity of ρ 4 × 10-8Ωm. Assume a potential of 4 V is maintained at the left end of the wire at x = 0. Alsoassume V = 0 at x = 0.5 m. Find (a) the magnitude and direction of the electric field in thewire, (b) the resistance of the wire, (c) the magnitude and direction of the electric currentin the wire, and (d) the current density in the wire. (e) Show that E = ρ J. (E = −dVdx)arrow_forward
- (b) A voltage of 3 V is applied across the ends of a copper alloy conductor which has a resistance of 1.5 at room temperature (20 °C). The conductor has a length of 20 m and a diameter of 0.7 mm. (i) (ii) (iii) Calculate the current which flows through the copper alloy conductor and the current density in it. What is the electrical conductivity of the material? After a while, the temperature in the copper alloy conductor rises and its resistance becomes 2.4 №. If the temperature coefficient of resistance of the copper alloy is 0.004/°C at 20 °C, calculate the temperature to which the conductor has risen.arrow_forwardA rod of semiconducting material of Length L=5 m and cross-sectional area A=3 mm2 lies along the x-axis between x=0 and x=L. The material obeys ohm’s Law, and its resistivity varies along the rod according to ρ = ρ0*( 1 - x2/L2) where ρ0=4.5 x 10-4 Ω.m. The end of the rod at x=0 is at potential V0=25 V greater than the end at x=L. What is the total resistance, in units of Ω, of the rod? What is the current, in units of miliamperes, in the rod? What is the electric potential, in units of volt, in the rod at x=L/2?arrow_forwardAn aluminum rod with a square cross section is 2.3 m long and 6.5 mm on edge. (a) What is the resistance between its ends? (b) What must be the diameter of a cylindrical copper rod of length 2.3 m if its resistance is to be the same as that of the aluminum rod? The resistivity of aluminum is 2.75 x 10-8 Q-m and the resistivity of copper is 1.69 x 10-8 Q-m. (a) Number i Units (b) Number Unitsarrow_forward
- An independent and constant current source is supplying 0.6 ampere to a uniform copper conductor with length 40 mm, inner radius 7 mm, and outer diameter 20 mm. If the resistivity and the electron concentration of the conductor are 2.4 x 10-8 ohm-meter and 6.4 x 1024 electrons per cubic meter, respectively: a. The drift velocity in the conductor; (5 points) b. The voltage across the conductor; (5 points)arrow_forwardA rod of semiconducting material of Length L=5 m and cross-sectional area A=3 mm2 lies along the x-axis between x=0 and x=L. The material obeys ohm’s Law, and its resistivity varies along the rod according to ρ = ρ0*( 1 - x2/L2) where ρ0=4.5 x 10-4 Ω.m. The end of the rod at x=0 is at potential V0=25 V greater than the end at x=L. What is the total resistance, in units of Ω, of the rod? What is the current, in units of miliamperes, in the rod? What is the electric potential, in units of volt, in the rod at x=L/2? What is the electric-field magnitude E, in units of V/m, in the rod at x=L/2?arrow_forward(a) A 35.1-m length of copper wire at 20.0°C has a radius of 0.23 mm. If a potential difference of 7.0 V is applied across the length of the wire, determine the current in the wire. (Use the values in the following table.) Resistivities and Temperature Coefficients of Resistivity for Various Materials (at 20°C) Material Resistivity(Ω · m) Temperature Coefficientof Resistivity [(°C)−1] Silver 1.59 ✕ 10−8 3.8 ✕ 10−3 Copper 1.7 ✕ 10−8 3.9 ✕ 10−3 Gold 2.44 ✕ 10−8 3.4 ✕ 10−3 Aluminum 2.82 ✕ 10−8 3.9 ✕ 10−3 Tungsten 5.6 ✕ 10−8 4.5 ✕ 10−3 Iron 10.0 ✕ 10−8 5.0 ✕ 10−3 Platinum 11 ✕ 10−8 3.92 ✕ 10−3 Lead 22 ✕ 10−8 3.9 ✕ 10−3 Nichromea 150 ✕ 10−8 0.4 ✕ 10−3 Carbon 3.5 ✕ 10−5 −0.5 ✕ 10−3 Germanium 0.46 −48 ✕ 10−3 Silicon 640 −75 ✕ 10−3 Glass 1010–1014 Hard rubber ≈1013 Sulfur 1015 Quartz (fused) 75 ✕ 1016 aA nickel–chromium alloy commonly used in heating elements. ??A(b) If the wire is heated to 36.0°C while the 7.0-V potential difference is…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Ohm's law Explained; Author: ALL ABOUT ELECTRONICS;https://www.youtube.com/watch?v=PV8CMZZKrB4;License: Standard YouTube License, CC-BY