Fundamentals of Physics, Volume 1, Chapter 1-20
10th Edition
ISBN: 9781118233764
Author: David Halliday
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 26, Problem 65P
A potential difference V is applied to a wire of cross-sectional area A, length L, and resistivity p. You want to change the applied potential difference and stretch the wire so that the energy dissipation rate is multiplied by 30.0 and the current is multiplied by 4.00. Assuming the wire’s density does not change, what are (a) the ratio of the new length to L and (b) the ratio of the new cross-sectional area to A?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A potential difference Vis applied to a wire of cross sectional area A, length L, and resistivity p. You want to change the applied
potential difference and stretch the wire so that the energy dissipation rate is multiplied by 38.0 and the current is multiplied by 4.65.
Assuming the wire's density does not change, what are (a) the ratio of the new length to L and (b) the ratio of the new cross-sectional
area to A?
(a) Number i
(b) Number i
Units
Units
A potential difference V is applied to a wire of cross-sectional area A, length L, and resistivity r.You want to change the applied potential difference and stretch the wire so that the energy dissipation rate is multiplied by 30.0 and the current is multiplied by 4.00. Assuming the wire’s density does not change, what are (a) the ratio of the new length to L and (b) the ratio of the new cross-sectional area to A?
A metallic conductor has a resistivity of 2 x10-6 Qm. What is the
resistance of a piece that is 40 m long and has a uniform cross
sectional area of 3.4 x10-6 m2?lf the potential difference across the
source is 2.7 volts, find the current flows through the conductor.
(a) Resistance of the conductor (in Q) =
(b) current flows through the conductor in A =
Chapter 26 Solutions
Fundamentals of Physics, Volume 1, Chapter 1-20
Ch. 26 - Figure 26-15 shows cross sections through three...Ch. 26 - Figure 26-16 shows cross sections through three...Ch. 26 - Figure 26-17 shows a rectangular solid conductor...Ch. 26 - Figure 26-18 shows plots of the current i through...Ch. 26 - Figure 26-19 shows four situations in which...Ch. 26 - In Fig. 26-20, a wire that carries a current...Ch. 26 - Figure 26-21 gives the electric potential Vx...Ch. 26 - The following table give the lengths of three...Ch. 26 - Prob. 9QCh. 26 - Three wires, of the same diameter, are connected...
Ch. 26 - Figure 26-23 gives, for three wires of radius R,...Ch. 26 - During the 4.0 min a 5.0 A current is set up in a...Ch. 26 - An isolated conducting sphere has a 10 cm radius....Ch. 26 - A charged belt, 50 cm wide, travels at 30 m/s...Ch. 26 - The United States National Electric Code, which...Ch. 26 - SSM WWW A beam contains 2.0 108 doubly charged...Ch. 26 - A certain cylindrical wire carries current. We...Ch. 26 - A fuse in an electric circuit is a wire that is...Ch. 26 - Prob. 8PCh. 26 - The magnitude Jr of the current density in a...Ch. 26 - The magnitude J of the current density in a...Ch. 26 - What is the current in a wire of radius R = 3.40...Ch. 26 - Near Earth, the density of protons in the solar...Ch. 26 - Prob. 13PCh. 26 - A human being can be electrocuted if a current as...Ch. 26 - SSM A coil is formed by winding 250 turns of...Ch. 26 - Copper and aluminium are being considered for a...Ch. 26 - Prob. 17PCh. 26 - A wire 4.00 m long and 6.00 mm in diameter has a...Ch. 26 - SSM What is the resistivity of a wire of 1.0 mm...Ch. 26 - Prob. 20PCh. 26 - ILW A common flashlight bulb is rated at 0.30 A...Ch. 26 - Kiting during a storm. The legend that Benjamin...Ch. 26 - Prob. 23PCh. 26 - GO Figure 26-25a gives the magnitude Ex of the...Ch. 26 - SSM ILW A wire with a resistance of 6.0 is drawn...Ch. 26 - In Fig. 26-26a. a 9.00 V battery is connected to a...Ch. 26 - SSM WWW Two conductors are made of the same...Ch. 26 - GO Figure 26-27 gives the electric potential Vx...Ch. 26 - Prob. 29PCh. 26 - Prob. 30PCh. 26 - Prob. 31PCh. 26 - Prob. 32PCh. 26 - Prob. 33PCh. 26 - GO Figure 26-29 shows wire section 1 of diameter...Ch. 26 - GO In Fig. 26-30, current is set up through a...Ch. 26 - GO Swimming during a storm. Figure 26-31 shows a...Ch. 26 - Prob. 37PCh. 26 - In Fig. 26-32a, a 20 resistor is connected to a...Ch. 26 - A certain brand of hot-dog cooker works by...Ch. 26 - Thermal energy is produced in a resistor at a rate...Ch. 26 - SSM A 1220 V potential difference is applied to a...Ch. 26 - In Fig. 26-33, a battery of potential difference V...Ch. 26 - ILW An unknown resistor is connected between the...Ch. 26 - A student kept his 6.0 V, 7.0 W radio turned on at...Ch. 26 - SSM ILW A 1250 W radiant heater is constructed to...Ch. 26 - A copper wire of cross-sectional area 2.00 106 m2...Ch. 26 - A heating element is made by maintaining a...Ch. 26 - Exploding shoes. The rain-soaked shoes of a person...Ch. 26 - A 100 W lightbulb is plugged into a standard 120 V...Ch. 26 - GO The current through the battery and resistors 1...Ch. 26 - GO SSM WWW Wire C and wire D are made from...Ch. 26 - GO The current-density magnitude in a certain...Ch. 26 - A 120 V potential difference is applied to a space...Ch. 26 - Go Figure 26-36a shows a rod of resistive...Ch. 26 - SSM A Nichrome heater dissipates 500 W when the...Ch. 26 - Prob. 56PCh. 26 - An 18.0 W device has 9.00 V across it. How much...Ch. 26 - An aluminum rod with a square cross section is 1.3...Ch. 26 - A cylindrical metal rod is 1.60 m long and 5.50 mm...Ch. 26 - The chocolate crumb mystery. This story begins...Ch. 26 - SSM A steady beam of alpha particles q = 2e...Ch. 26 - A resistor with a potential difference of 200 V...Ch. 26 - A 2.0 kW heater element from a dryer has a length...Ch. 26 - cylindrical resistor of radius 5.0 mm and length...Ch. 26 - A potential difference V is applied to a wire of...Ch. 26 - The headlights of a moving car require about 10 A...Ch. 26 - A 500 W heating unit is designed to operate with...Ch. 26 - The copper windings of a motor have a resistance...Ch. 26 - How much electrical energy is transferred to...Ch. 26 - A caterpillar of length 4.0 cm crawls in the...Ch. 26 - Prob. 71PCh. 26 - A steel trolley-car rail has a cross-sectional...Ch. 26 - A coil of current-carrying Nichrome wire is...Ch. 26 - Prob. 74PCh. 26 - A certain x-ray tube operates at a current of 7.00...Ch. 26 - A current is established in a gas discharge tube...Ch. 26 - In Fig.26-37, a resistance coil wired to an...Ch. 26 - An insulating belt moves at speed 30 m/s and has a...Ch. 26 - In a hypothetical fusion research lab, high...Ch. 26 - When a metal rod is heated, not only its...Ch. 26 - A beam of 16 MeV deuterons from a cyclotron...Ch. 26 - A linear accelerator produces a pulsed beam of...Ch. 26 - An electric immersion heater normally takes 100...Ch. 26 - A 400 W immersion heater is placed in a pot...Ch. 26 - A 30 F capacitor is connected across a programmed...
Additional Science Textbook Solutions
Find more solutions based on key concepts
Centrifuges are widely used in biology and medicine to separate cells and other particles from liquid suspensio...
Essential University Physics: Volume 1 (3rd Edition)
15. How do weight and mass differ?
Applied Physics (11th Edition)
Under what conditions can the electric flux through a surface be written as EA. where A is the surface area?
Essential University Physics (3rd Edition)
The rank of the carts by kinetic energy before they meet the incline.
Conceptual Physics: The High School Physics Program
2. (I) A delivery truck travels 21 blocks north, 16 blocks east, and 26 blocks south. What is its final displac...
Physics: Principles with Applications
If the pressure and volume of a system are given, is the temperature always uniquely determined?
University Physics Volume 2
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- An aluminum wire 1.628 mm in diameter (14-gauge) carries a current of 3.00 amps, (a) What is the absolute value of the charge density in the wire? (b) What is the drift velocity of the electrons? (c) What would be the drift velocity if the same gauge copper were used instead of aluminum? The density of copper is 8.96 g/cm3 and thedensity of aluminum is 2.70 g/cm3. The molar mass ofaluminum is 26.98 g/mol and the molar mass of copper is 63.5 g/mol. Assume each atom of metal contributes one free electron.arrow_forward(a) During surgery, a current as small as 20.0A applied directly to the heart may cause ventricular fibrillation. If the resistance of the exposed heart is 300 what is the smallest voltage that poses thisdanger? (b) Does your answer imply that special electrical safetyprecautions are needed?arrow_forwardTaking R = 1.00 k and = 250 V in Figure P21.49, determine the direction and magnitude of the current in the horizontal wire between a and e. Figure P21.49arrow_forward
- A strip of doped silicon 260.0 um wide contains 8.80 x 10-2 conduction electrons per cubic meter and an insignificant number of holes. When the strip carries a current of 102 µA, the drift speed of the electrons is 59.6 cm/s. What is the thickness of the strip? Umarrow_forwardA material is formed into a long rod with a square cross-section 0.50 cm on each side. When a 100 V voltage is applied across a 20 m length of the rod, a 5.0 A current is carried. a) What is the resistivity of the material? ρ = _______ Ω m b) Is the material a conductor, an insulator, or a semiconductor?arrow_forwardThe strain in a wire can be monitored and computed by measuring the resistance of the wire. Let Li represent the original length of the wire, Ai its original cross-sectional area, Ri = ρLi /Ai the original resistance between its ends, and δ = ΔL/Li = (L - Li )/Li the strain resulting from the application of tension. Assume the resistivity and the volume of the wire do not change as the wire stretches. (a) Show that the resistance between the ends of the wire under strain is given by R = Ri (1 + 2δ + δ2). (b) If the assumptions are precisely true, is this result exact or approximate? Explain your answer.arrow_forward
- A current I =0.35 A flows through a cylindrical resistor made out of some unknown ceramic-like composite. The radius of the cylindrical body is 4.25 mm while the length is 1.65 cm. If the potential drop over the resistor is 7.54 V, what is the resistivity of the unknown ceramic material? (Answer in Ohm*m)arrow_forwardIn a 100-m-long conductor of cylindrical cross-section (radius ro = 5 mm), the axial current density is J = î2 A/m². The conductivity is o= 5.8-107 S/m. Find a) the current flowing through the conductor, b) the voltage across the entire length of the conductor, c) the overall resistance of the conductor.arrow_forwardA copper wire of radius a = 0.172 mm has an aluminum jacket of outer radius b = 0.231 mm. There is a current i = 1.58A in the composite wire. Take the resistivity for copper and aluminum to be 1.69 × 10-Q-m and 2.75 × 10*°Q-m. Calculate the current in (a) the copper and (b) the aluminum. (c) If a potential difference V = 10.4 V between the ends maintains the current, what is the length in meters of the composite wire? (a) Number i Units (b) Number i Units (c) Number i Unitsarrow_forward
- A potential difference of 12 V is found to produce a current of 0.40 A in a 3.2 m length of wire with a uniform diameter of 0.80 cm. a) What is the value of the resistivity of the wire, and b) the resistance of the wire?arrow_forwardPart (a) I measure the resistance of this wire and find it to be R = 156 Q. What is the resistivity of the material the wire is made out of? p= Problem 7: A particular wire has a length of L = 2.7 m and a circular cross-sectional area of radius r= 1.69 mm. G= sin() cos cotan() asin()) acotan() atan() cosh() tanh() I= sin()) cos() cotan() asin() sinh() atan() acotan cosh() tanh() cotanh() Degrees O Radians B Degrees O Radians Part (b) What is the conductivity of this wire, in inverse Ohms per meter? 0 tan()) π ( acos() E ^^^L sinh() cotanh() g L P Y d h m r tan() π acos() E ^^^^ π E 1 Part (c) Give an expression for the current density in the wire if an electric field E is passing through it. Write this in terms of the resistivity and the other variables in the problem. J= n R ( ^^^ sin() cos() cotan() asin() atan() acotan() cosh() + + 7 8 9 4 5 6 1 2 3 0 END NO BACKSPACE DEL CLEAR Part (d) Calculate the current in the wire, in milliamperes, if the field strength is 5.28 V/m. - END NO…arrow_forwardA wire of Nichrome is 1.0 m long and 2.5 mm2 in cross-sectional area. It carries a current of 4.0 A. When a 12.0 V potential difference is applied between the ends. Calculate the conductivity δ of the Nichrome.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Circuits, Voltage, Resistance, Current - Physics 101 / AP Physics Review with Dianna Cowern; Author: Physics Girl;https://www.youtube.com/watch?v=q8X2gcPVwO0;License: Standard YouTube License, CC-BY