EBK MANUFACTURING ENGINEERING & TECHNOL
EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 27, Problem 23QLP

Describe your thoughts regarding the laser-beam machining of nonmetallic materials. Give several possible applications, including their advantages compared with other processes.

Blurred answer
Students have asked these similar questions
Calculate the material removal rate and electrode feed rate in the electrochemical machining of an iron surface that is 25 mm × 25 mm in cross-section, using NaCl in water as electrolyte. The gap between the tool and the work-piece is 0.25 mm. The supply voltage is 12 volt D.C. The specific resistance of electrolyte is 3 2 cm. Take for iron: Valency = 2, Atomic weight = 55.85,Density = 7860 kg/m³.
For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a matrix of 0.1 mm (0.004 in) diameter holes in a plate of 3.2 mm (0.125 in) thick hardened tool steel. The matrix is rectangular, 75 by 125 mm (3.0 by 5.0 in) with the separation between holes in each direction = 1.6 mm ( 0.0625 in).
(b) During a certain machining experiment at the UCSI workshop, it is observed that temperature at the tool workpiece interface is 1200 °C at a cutting speed of 300 mm/min with a feed rate of 0.002 mm/rev. (1) Analyse how the temperature will be affected if the cutting speed is increased by 100 %. (ii) Detemine the cutting speed necessary to achieve a maximum cutting temperature of 900 °C.

Chapter 27 Solutions

EBK MANUFACTURING ENGINEERING & TECHNOL

Ch. 27 - What type of workpiece is not suitable for...Ch. 27 - What is an undercut? Why must it be considered in...Ch. 27 - Explain the principle of hybrid machining.Ch. 27 - Give technical and economic reasons that the...Ch. 27 - Why is the preshaping or premachining of parts...Ch. 27 - Explain why the mechanical properties of workpiece...Ch. 27 - Prob. 17QLPCh. 27 - Prob. 18QLPCh. 27 - Why has electrical-discharge machining become so...Ch. 27 - Prob. 20QLPCh. 27 - Which of the advanced machining processes would...Ch. 27 - Which of the processes described in require a...Ch. 27 - Describe your thoughts regarding the laser-beam...Ch. 27 - Are deburring operations still necessary for some...Ch. 27 - List and explain factors that contribute to a poor...Ch. 27 - What is the purpose of the abrasives in...Ch. 27 - Which of the processes described in this chapter...Ch. 27 - Is kerf width important in wire EDM? Explain.Ch. 27 - Comment on your observations regarding Fig. 27.4.Ch. 27 - Why may different advanced machining processes...Ch. 27 - A 200-mm-deep hole that is 30 mm in diameter is...Ch. 27 - If the operation in Problem 27.31 were performed...Ch. 27 - A cutting-off operation is being performed with a...Ch. 27 - A 0.80-in.-thick copper plate is being machined by...Ch. 27 - Explain why it is difficult to produce sharp...Ch. 27 - Make a list of the processes described in this...Ch. 27 - Would the processes described in this chapter be...Ch. 27 - Prob. 38SDPCh. 27 - Describe your thoughts as to whether the...Ch. 27 - Make a list of machining processes that may be...Ch. 27 - At what stage is the abrasive in abrasive...Ch. 27 - Describe the similarities and differences among...Ch. 27 - Describe the similarities and differences among...Ch. 27 - Describe any workpiece size limitations in...Ch. 27 - Suggest several design applications for the types...Ch. 27 - Based on the topics covered in Parts III and IV,...Ch. 27 - Review Example 27.1 and explain the relevant...Ch. 27 - Precision engineering is a term that is used to...Ch. 27 - With appropriate sketches, describe the principles...Ch. 27 - Make a table of the process capabilities of the...Ch. 27 - One of the general concerns regarding advanced...Ch. 27 - It can be seen that several of the processes...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY