Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
5th Edition
ISBN: 9780133994612
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 27, Problem 4CQ
A water pump can fail to provide the proper amount of flow of coolant through the cooling system if what has happened?
- a. The coolant is leaking from the weep hole.
- b. The bearing is noisy.
- c. The impeller blades are worn or slipping on the shaft.
- d. A bearing failure has caused the shaft to become loose.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
For the fluid power automobile lift system of Fig. 1, the hydraulic piston has a 250-mm diameter. How much of oil pressure (kPa) is required to lift a 13300 N automobile?
What causes coolant to leak from the water
pump weep hole?
Select one:
a. A faulty thermostat
b. A faulty radiator cap
C. A faulty bypass hose
d. A faulty pump shaft seal
Which among the valves is called non return valve
a.flap check
b.ball
c.plunger valve
d.diaphragm
e.Check
Chapter 27 Solutions
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Ch. 27 - How can a thermostat fail?Ch. 27 - How can a water pump fail, requiring replacement?Ch. 27 - Prob. 3RQCh. 27 - Why must timing belts be replaced?Ch. 27 - Why is it important that the READY light be out on...Ch. 27 - Prob. 1CQCh. 27 - Prob. 2CQCh. 27 - Coolant drained from the cooling system when...Ch. 27 - A water pump can fail to provide the proper amount...Ch. 27 - Intake manifold gaskets on a V-type engine can...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to t...
Mechanics of Materials (10th Edition)
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
The triple jump is a track-and-field event in which an athlete gets a running start and tries to leap as far as...
Vector Mechanics For Engineers
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which among the following is not correct statement on poppet valve. O a. Less wear on internal seals o b. Simple construction, easy repair and maintenance. O c. They are balanced type O d. Negligible leakagearrow_forwardIf oil pressure is higher than specifications: Select one: a. there may be excessive clearance in the engine bearings. b. the oil pump may be worn. c. the engine is noisy. d. the oil pressure regulator might be stickingarrow_forwardThe turbine is connected to generator which converts mechanical energy to electrical energy. A. True B. Falsearrow_forward
- If the oil on the dipstick looks milky gray, it is possible that there is water (or coolant) being mixed into the oil. This could have been caused by any of the following EXCEPΤ: Select one: a. a bad head gasket. b. a cracked head. C. a leaky oil cooler. d. a leaky fuel injector.arrow_forwardA vehicle comes in with no coolant and a core plug popped out of the engine block. Technician A states that the water pump is likely to be overpressurizing the system. Technician B states that the coolant may not have a low enough freezing point. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A andB d. Neither Technician A nor Barrow_forwardWhen fitting a freshly ground valve into a freshly ground seat: Technician A says that the seat should be ground more with the same stone if the margin is too small. Technician B says that the seat should be ground more with the same stone if the valve seat is too high. Who is correct?arrow_forward
- is a type of safety valve used to control or limit the pressure in a system. Select one: O a. On and off valve O b. One way flow control valve O . Shutoff valve O d. Pressure relief valvearrow_forwardTechnician A uses a feeler gauge and straightedge to determine the pump cover flatness.Technician B uses an outside micrometer tomeasure the diameter and thickness of theouter rotor. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardThe diesel engines operates with low pressure than petrol engine a. FALSE b. TRUEarrow_forward
- What part of a relief valve covers the exhaust port? A. Cap B. Ball C. Spring D. Diaphragmarrow_forwardWhen installing a spin-on oil filter, failure to lube the O-ring will: Select one: a. lead to double gasketing. b. damage the threads on the adapter. C. cause it to bind and roll out of the oil filter groove. d. damage the threads on the adapter.arrow_forwardWhen performing a coolant pressure test, Technician A says to pressurize the system to the pressure shown on the radiator cap. Technician B says that the coolant should be drained before performing the test. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY