EBK THERMODYNAMICS: AN ENGINEERING APPR
8th Edition
ISBN: 8220100257056
Author: CENGEL
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2.8, Problem 130FEP
To determine
The electric power output of hydroelectric power plant.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In rural housing the water source is obtained through groundwater pumped upwards. Suppose the groundwater source has a depth of 60 m from the surface. The water will be lifted as far as 5 m above ground level with a pump. The diameter of the pipe inlet is 10 cm and the outlet is 15 cm.By ignoring the interaction of heat with the environment and heat due to friction, determine the input work (Watt) required by the pump for the water to flow stable at a rate of 15 liters / s. (Water type mass 1000 kg / m ^ 3). (Application of the 1st Law of Thermodynamics to open systems)
Electric power is to be generated by installing a hydraulic turbine-generator at a site 77 m below
the free surface of a large water reservoir that can supply water steadily at a rate of 850 kg/s. If
the mechanical power output of the turbine is 520 kW and the electric power generation is 460
kW, determine:
a) the turbine efficiency and
b) the combined turbine-generator efficiency of this plant
Neglect losses in the pipes.
850 kg/s
T
77 m
Water is pumped from a lake to a storage tank 25 m above at a rate of 70 L's while consuming 22.4 kW of electric power. Disregarding any frictional losses in the pipes and any changes in
kinetic energy, determine the overall efficiency of the pump-motor unit.
Storage tank
25 m
Pump
Chapter 2 Solutions
EBK THERMODYNAMICS: AN ENGINEERING APPR
Ch. 2.8 - What is total energy? Identify the different forms...Ch. 2.8 - List the forms of energy that contribute to the...Ch. 2.8 - How are heat, internal energy, and thermal energy...Ch. 2.8 - What is mechanical energy? How does it differ from...Ch. 2.8 - Natural gas, which is mostly methane CH4, is a...Ch. 2.8 - Portable electric heaters are commonly used to...Ch. 2.8 - Prob. 7PCh. 2.8 - Prob. 8PCh. 2.8 - 2–9E Calculate the total potential energy, in Btu,...Ch. 2.8 - Prob. 10P
Ch. 2.8 - Prob. 11PCh. 2.8 - At a certain location, wind is blowing steadily at...Ch. 2.8 - A water jet that leaves a nozzle at 60 m/s at a...Ch. 2.8 - Prob. 14PCh. 2.8 - Prob. 15PCh. 2.8 - Consider a river flowing toward a lake at an...Ch. 2.8 - When is the energy crossing the boundaries of a...Ch. 2.8 - Consider an automobile traveling at a constant...Ch. 2.8 - A gas in a pistoncylinder device is compressed,...Ch. 2.8 - A room is heated by an iron that is left plugged...Ch. 2.8 - A room is heated as a result of solar radiation...Ch. 2.8 - Prob. 23PCh. 2.8 - A small electrical motor produces 5 W of...Ch. 2.8 - Prob. 25PCh. 2.8 - 2–26C Lifting a weight to a height of 20 m takes...Ch. 2.8 - Prob. 27PCh. 2.8 - Prob. 28PCh. 2.8 - Prob. 29PCh. 2.8 - Prob. 30PCh. 2.8 - Prob. 31PCh. 2.8 - Prob. 32PCh. 2.8 - Prob. 33PCh. 2.8 - A ski lift has a one-way length of 1 km and a...Ch. 2.8 - The engine of a 1500-kg automobile has a power...Ch. 2.8 - Prob. 36PCh. 2.8 - What are the different mechanisms for transferring...Ch. 2.8 - On a hot summer day, a student turns his fan on...Ch. 2.8 - Prob. 39PCh. 2.8 - A vertical pistoncylinder device contains water...Ch. 2.8 - At winter design conditions, a house is projected...Ch. 2.8 - A water pump increases the water pressure from 15...Ch. 2.8 - Prob. 43PCh. 2.8 - Prob. 44PCh. 2.8 - A university campus has 200 classrooms and 400...Ch. 2.8 - Prob. 46PCh. 2.8 - Consider a room that is initially at the outdoor...Ch. 2.8 - Prob. 48PCh. 2.8 - 2-49 The 60-W fan of a central heating system is...Ch. 2.8 - Prob. 50PCh. 2.8 - An escalator in a shopping center is designed to...Ch. 2.8 - Prob. 52PCh. 2.8 - How is the combined pumpmotor efficiency of a pump...Ch. 2.8 - Prob. 54PCh. 2.8 - Can the combined turbinegenerator efficiency be...Ch. 2.8 - Consider a 2.4-kW hooded electric open burner in...Ch. 2.8 - Prob. 57PCh. 2.8 - Prob. 58PCh. 2.8 - Prob. 59PCh. 2.8 - A geothermal pump is used to pump brine whose...Ch. 2.8 - Prob. 62PCh. 2.8 - Prob. 63PCh. 2.8 - The water in a large lake is to be used to...Ch. 2.8 - A 7-hp (shaft) pump is used to raise water to an...Ch. 2.8 - At a certain location, wind is blowing steadily at...Ch. 2.8 - Reconsider Prob. 265. Using appropriate software,...Ch. 2.8 - Water is pumped from a lake to a storage tank 15 m...Ch. 2.8 - Prob. 69PCh. 2.8 - A hydraulic turbine has 85 m of elevation...Ch. 2.8 - Prob. 71PCh. 2.8 - Water is pumped from a lower reservoir to a higher...Ch. 2.8 - Prob. 73PCh. 2.8 - An oil pump is drawing 44 kW of electric power...Ch. 2.8 - How does energy conversion affect the environment?...Ch. 2.8 - What is acid rain? Why is it called a rain? How do...Ch. 2.8 - Why is carbon monoxide a dangerous air pollutant?...Ch. 2.8 - What is the greenhouse effect? How does the excess...Ch. 2.8 - What is smog? What does it consist of? How does...Ch. 2.8 - Prob. 80PCh. 2.8 - Consider a household that uses 14,000 kWh of...Ch. 2.8 - When a hydrocarbon fuel is burned, almost all of...Ch. 2.8 - Prob. 83PCh. 2.8 - A typical car driven 20,000 km a year emits to the...Ch. 2.8 - What are the mechanisms of heat transfer?Ch. 2.8 - Which is a better heat conductor, diamond or...Ch. 2.8 - How does forced convection differ from natural...Ch. 2.8 - What is a blackbody? How do real bodies differ...Ch. 2.8 - Define emissivity and absorptivity. What is...Ch. 2.8 - Does any of the energy of the sun reach the earth...Ch. 2.8 - The inner and outer surfaces of a 5-m 6-m brick...Ch. 2.8 - The inner and outer surfaces of a 0.5-cm-thick 2-m...Ch. 2.8 - Reconsider Prob. 292. Using appropriate software,...Ch. 2.8 - Prob. 94PCh. 2.8 - Prob. 95PCh. 2.8 - Prob. 96PCh. 2.8 - Prob. 97PCh. 2.8 - For heat transfer purposes, a standing man can be...Ch. 2.8 - Prob. 99PCh. 2.8 - Prob. 100PCh. 2.8 - A 1000-W iron is left on the ironing board with...Ch. 2.8 - A 7-cm-external-diameter, 18-m-long hot-water pipe...Ch. 2.8 - A thin metal plate is insulated on the back and...Ch. 2.8 - Reconsider Prob. 2103. Using appropriate software,...Ch. 2.8 - The outer surface of a spacecraft in space has an...Ch. 2.8 - Prob. 106PCh. 2.8 - A hollow spherical iron container whose outer...Ch. 2.8 - Consider a vertical elevator whose cabin has a...Ch. 2.8 - Consider a homeowner who is replacing his...Ch. 2.8 - Prob. 110RPCh. 2.8 - Prob. 111RPCh. 2.8 - Prob. 112RPCh. 2.8 - 2–113 The U.S. Department of Energy estimates that...Ch. 2.8 - Prob. 114RPCh. 2.8 - Prob. 115RPCh. 2.8 - Prob. 116RPCh. 2.8 - Prob. 117RPCh. 2.8 - Consider a TV set that consumes 120 W of electric...Ch. 2.8 - Water is pumped from a 200-ft-deep well into a...Ch. 2.8 - Prob. 120RPCh. 2.8 - Prob. 121RPCh. 2.8 - In a hydroelectric power plant, 65 m3/s of water...Ch. 2.8 - The demand for electric power is usually much...Ch. 2.8 - The pump of a water distribution system is powered...Ch. 2.8 - On a hot summer day, the air in a well-sealed room...Ch. 2.8 - Prob. 126FEPCh. 2.8 - A 2-kW electric resistance heater in a room is...Ch. 2.8 - A 900-kg car cruising at a constant speed of 60...Ch. 2.8 - Prob. 129FEPCh. 2.8 - Prob. 130FEPCh. 2.8 - Prob. 131FEPCh. 2.8 - A 2-kW pump is used to pump kerosene ( = 0.820...Ch. 2.8 - Prob. 133FEPCh. 2.8 - Prob. 134FEPCh. 2.8 - Prob. 135FEPCh. 2.8 - Prob. 136FEPCh. 2.8 - Prob. 137FEPCh. 2.8 - Heat is transferred steadily through a...Ch. 2.8 - The roof of an electrically heated house is 7 m...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water in the rural areas is often extracted from underground water source whose free surface is 65m below ground level. The water is to be raised 5 m above the ground by a pump. The diameter of the pipe is 10 cm at the inlet and 15 cm at the exit. Neglecting any heat interaction with the surroundings and frictional heating effects. What is the necessary power input to the pump in kW for a steady flow of water at the rate of 0.55 m3/s? Assume pump efficiency of 75%.arrow_forwardWater is pumped from a lake to a storage tank 15 m above at a rate of 70 L/s while consuming 15.4 kW of electric power, as shown in Figure 4 below. Disregarding any frictional losses in the pipes and any changes in kinetic energy, determine a) the overall efficiency of the pump-motor unit and; b) the pressure difference between the inlet and the exit of the pump. Storage tank 15 m Pump Figure 4arrow_forwardA 10,000 KW run-of-river hydro-electric plant has an available head of 200 ft and has an overall efficiency of 90% that remains constant for all loads. For a given day during the low-water season the customers receiving primary power have the following loads: 8000KW for 2 hrs, 6000 KW for 2 hours, 4000 KW for 10 hrs, 2000 KW for 10 hrs. For a river flow remaining onstant at 525 ft/s, how much secondary power could this plant provide during the entire day?arrow_forward
- Water is stored in an elevated reservoir. To generate power, water flows from this reservoir down through a large conduit to a turbine and then through a similar-sized conduit. At a point in the conduit 89.5 m above the turbine, the pressure is 172.4 kPa and at a level 5 m below the turbine, the pressure is 89.6 kPa The water flow rate is 0.800ms The output of the shaft the turbine is 658 kW. The water density is 1000 ke m. If the efficiency of the turbine in converting the mechanical energy gven up by the fluid to the turbine shaft is 89 % (n =0.89). a) Draw a schematic diagram for the process b) Calculate the frictional loss in the turbine in J kg %3Darrow_forwardelectric power is to be generated by installing a hydraulic turbine-generator at a site 120 m below the free surface of a large water reservoir that can supply water at a rate of 2400 kg/s steadily. determine the power generation potential.arrow_forwardWater is pumped from a lake to a storage tank 30 m above at a rate of 75 L/s while consuming 21.8 kW of electric power, as shown in figure below. Disregarding any frictional losses in the pipes and any changes in kinetic energy, determine the overall efficiency of the pump-motor unit. 30 m Pump Storage tankarrow_forward
- A water from Agno River is pumped using a submerged pump at an efficiency of 78% that is discharged to a swimming pool in Itogon which has a free surface of 30 m above the Agno River water level. The pipe that was used has a diameter of 7 cm on the suction line and 5 cm on the discharge line from the pump. If the power requirement of the pump is 5 kW assuming that the elevation difference between the pump inlet and outlet and the effect of the kinetic energy correction factors are negligible, calculate for the followinga) Power requirement by the pump in kWb) Pressure difference across the pumpc) Pumping cost/day(24 hour) if the electricity cost is ₱2.00/kW-hrarrow_forwardA pumped storage scheme comprises two reversible pump turbines which transfer water between an upper and lower reservoir with a head difference of 400m. During a typical daily cycle, electrical power of 120kW is supplied to the pumps which deliver 15 litres/s for 6 hours overnight to the upper reservoir. During the daylight hours, a flow of 10 litres/s is used to release the same quantity of water to generate electrical energy. If the efficiency during generation is 90%, how much energy is lost per day? d. A horizontal-axis wind turbine with rotor 80m in diameter is 40% efficient in 15m/s wind at 600m altitude and 30°C. Calculate the total amount of power the wind turbine would produce in those winds. TABLE 6.1 Density of Dry Air at a Pressure of 1 Atmosphere i. Temperature Temperature Density Density Ratio (°C) (°F) (kg/m³) (KT) iii. -15 -10 -5 5 10 15 : 30 35 40 5.0 14.0 23.0 32.0 41.0 50.0 59.0 68.0 77.0 $6.0 95.0 104.0 1.368 1.342 1.317 1.293 1.269 1.247 1.225 1.204 1.184 1.165…arrow_forwardA dam with a hydraulic turbine–generator located 40 m below the water surface has a rate of 4600 kg/s flowing through the penstock. If the electric power generated is measured to be 1400 kW and the generator efficiency is 95%, determine: (a) the overall efficiency of the turbine–generator, (b) the mechanical efficiency of the turbine, (c) the shaft power supplied by the turbine to the generator.arrow_forward
- An oil pump is drawing 40 kW of electric power while pumping oil with p = 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet diameters of the pipe are 8 cm and 12 cm, respectively. If the pressure rise of oil in the pump is measured to be 250kPa and the motor efficiency is 90 percent, determine the mechanical efficiency of the pump. 33.53 O 31.53 32.8 34.7 12 cm Pump 8 cm +4 AP=2 Oil AP=250 kPa 0.1m³/s 40 kW Motorarrow_forwardWater is pumped from a lake to a storage tank 18 m above at a rate of 70 L/s whileconsuming 20.4 kW of electric power. Disregarding any frictional losses in the pipes and anychanges in kinetic energy, determine (a) the overall efficiency of the pump–motor unit and (b)the pressure difference between the inlet and the exit of the pump.arrow_forwardA high reservoir holds water. Water travels from this reservoir down via a big conduit to a turbine and then down a second, similar-sized conduit to create electricity. The pressure is 172.4 kPa at a location in the conduit 89.5 m above the turbine and 89.6 kPa at a level 5 m below the turbine. The flow rate of water is 0.800 m3/s. The turbine's shaft produces 658 kW of power. The density of water is 1000 kg/m3. Calculate the friction loss in the turbine in J/kg if the turbine's efficiency in transferring the mechanical energy given up by the fluid to the turbine shaft is 89 percent (t = 0.89). It is worth noting that in the mechanical-energy-balance equation, Ws equals the output of the turbine's shaft multiplied by t. Note: Use the equation provided below MECHANICAL ENERGY BALANCES W s + gAz + F = AP F = AÛ • For frictionless processes in which no shaft work is performed, the mechanical energy balance is reduced to: ΔΡ Au² gAz = 0 Bernoulli Equationarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license