A+ Guide To It Technical Support
10th Edition
ISBN: 9780357108291
Author: ANDREWS, Jean.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Expert Solution & Answer
Chapter 3, Problem 12TC
Explanation of Solution
Given:
The DIMM rated at PC4 24000.
To find: The speed of the DIMM rated at PC4 24000 in MHz.
Solution:
The speed of a DIMM at a rate of PC4 24000 is 3000 MHz. The speed of a DIMM rated at PC4 24000 is calculated by dividing the PC rating by 8 bytes...
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
How does the "spin speed" (RPM) of an HDD impact its performance?
I want a report on the Raspberry Pi for a digital controlitem that should be for printing .
Computer Science
Embedded system
Write the code in MPLAB and apply it on Protues to make the led blink on bit five on port B?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Explain why the peripheral mapped 1/0 can only have 256 output ports.arrow_forward3. Equipment that uses RS 232 cables typically connects to a 9 pin port on a PC.The above statement is: a. TRUE b. FALSEarrow_forwardWhat is the role of GPIO (General-Purpose Input/Output) pins in microcontrollers?arrow_forward
- Which input device exists on MC8088/EV Microcomputer Trainer and will be used when it is needed to process an audio signal by the trainer?arrow_forwardQuestion 1 Given the below arduino code for a blinking LED: void setup() { int LED = 8 pinMode(LED,OUTPUT); } void loop() { digitalWrite(LED,HIGH); delay(200); digitalWrite(LED,LOW); delay(300); } Modify the code so that the LED is connected to pin 5 and the delay is one and half second between each blinking. What happened to the led speed blinking when the delay was changed?arrow_forwardThe VGA specifications give the following details for the parts of a single horizontal scan: Active Data 25.422 μs (colors!) Front Porch 0.636 μs (dark time) Sync Pulse 3.813 μs (dark time) Back Porch 1.907 μs (dark time) A. Calculate the total time for a complete horizontal scan line (sum all the parts above). Calculate the horizontal scan rate (how many scan lines per second?) expressed in kilohertz (kHz). B. Calculate the number of clock cycles for each of these parts of the signal, including the total (divide the time by the time per clock cycle, calculated in step 1). As a reality check, the data should be 640 pixels wide (remember, 1 clock cycle = 1 pixel) and the whole scan line should be 800 pixels. Round your answers to integers since we can only count in units of whole pixelsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- A+ Guide To It Technical SupportComputer ScienceISBN:9780357108291Author:ANDREWS, Jean.Publisher:Cengage,
Comptia A+ Core 1 Exam: Guide To Computing Infras...Computer ScienceISBN:9780357108376Author:Jean Andrews, Joy Dark, Jill WestPublisher:Cengage Learning
A+ Guide to Hardware (Standalone Book) (MindTap C...Computer ScienceISBN:9781305266452Author:Jean AndrewsPublisher:Cengage Learning
A+ Guide To It Technical Support
Computer Science
ISBN:9780357108291
Author:ANDREWS, Jean.
Publisher:Cengage,
Comptia A+ Core 1 Exam: Guide To Computing Infras...
Computer Science
ISBN:9780357108376
Author:Jean Andrews, Joy Dark, Jill West
Publisher:Cengage Learning
A+ Guide to Hardware (Standalone Book) (MindTap C...
Computer Science
ISBN:9781305266452
Author:Jean Andrews
Publisher:Cengage Learning