Principles of Foundation Engineering
9th Edition
ISBN: 9780357684832
Author: Das
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Question
Chapter 3, Problem 3.14P
To determine
Find the friction angle
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In a deposit of normally consolidated dry sand a cone penetration test was conducted. Following are the result:
Depth(m)
Point resistance of cone, qc (MN/m²)
1.5
2.06
3.0
4.23
4.5
6.01
6.0
8.18
7.5
9.97
9.0
12.42
Assuming the dry unit weight of sand to be 16kN/m³, estimale the average peak friction angle, ф’, fo the sand. Use ф’=tan ¯1((0.38+0.27log(qc/ σ’o))
Question attached
A dilatometer test was conducted in a sand deposit ata
depth of 6 m. The groundwater table was located at a depth
of 2 m below the ground surface. Given, for the sand:
3.29
- 14.5 kN/m3 and Yat 19.8 kN/m3. The contact stress
during the test was 260 kN/m2. Estimate the soil friction
angle, ф".
Chapter 3 Solutions
Principles of Foundation Engineering
Ch. 3 - Prob. 3.1PCh. 3 - Prob. 3.2PCh. 3 - Prob. 3.3PCh. 3 - Refer to Figure P3.3. Use Eqs. (3.10) and (3.11)...Ch. 3 - Prob. 3.5PCh. 3 - Prob. 3.6PCh. 3 - Prob. 3.7PCh. 3 - Prob. 3.8PCh. 3 - Prob. 3.9PCh. 3 - Prob. 3.10P
Ch. 3 - Prob. 3.11PCh. 3 - Prob. 3.12PCh. 3 - Prob. 3.13PCh. 3 - Prob. 3.14PCh. 3 - Prob. 3.15PCh. 3 - Prob. 3.16PCh. 3 - Prob. 3.17PCh. 3 - Prob. 3.18PCh. 3 - Prob. 3.19PCh. 3 - Prob. 3.20PCh. 3 - Prob. 3.21PCh. 3 - Prob. 3.22PCh. 3 - Prob. 3.23PCh. 3 - Prob. 3.24PCh. 3 - Prob. 3.25PCh. 3 - Prob. 3.26PCh. 3 - Prob. 3.27PCh. 3 - Prob. 3.28PCh. 3 - Prob. 3.29PCh. 3 - Prob. 3.30PCh. 3 - Prob. 3.31P
Knowledge Booster
Similar questions
- Mcqarrow_forwardA silty sand of density index (ID or Dr) = 59% was subjected to standard penetration tests at a depth of 3 m. Groundwater level occurred at a depth of 1.5 m below the surface of the soil which was saturated throughout and had a unit weight of 19.3 kN/m3. The average N count was 15. During calibration of the test equipment, the energy applied to the top of the driving rods was measured as 350 Joules. Determine the (N1)60 value for the soil.arrow_forward3. Following are the results of a standard penetration test in fine dry sand. N60 Depth (m) 1.5 7 13 3.0 18 4.5 22 6.0 7.5 24 For, the sand deposit, assume the mean grain size, D50, to be 0.26 mm and the unit weight of sand to be 15.5kN/m3. Estimate the variation of relative density with depth using the correlation developed by Cubrinovski and Ishihara. Assume pas100kN/m2. denined frictionarrow_forward
- Question A sample of dry sand was tested in direct shear test apparatus under a normal load of 72 kg. The shear load required to fail the sample was found to be 36 kg. The angle of internal friction () will be:arrow_forward3. A dilatometer test was conducted in a clay deposit. The groundwater table was located at a depth of 3 m below the surface. At a depth of 8 m below the surface, the contact pressure (Po) was 280 kN/m² and the expansion stress (p.) was 350 kN/m². Determine the following: (a) Coefficient of at-rest earth pressure, K, (b) Overconsolidation ratio, OCR (c) Modulus of elasticity, E, Assume o', at a depth of 8 m to be 95 kN/m? and µ, = 0.35.arrow_forwardA dilatometer test was conducted in a clay deposit. The groundwater table was locatedat a depth of 3 m below the surface. At a depth of 8 m below the surface, the contact pressure spod was 280 kN/m2 and the expansion stress sp1d was 350 kN/m2. Determinethe following:a. Coefficient of at-rest earth pressure, Kob. Overconsolidation ratio, OCRc. Modulus of elasticity, EsAssume s 9o at a depth of 8 m to be 95 kN/m2 and ms 5 0.35.arrow_forward
- 7.12 A sand specimen was subjected to a drained shear test using hollow cylin- der test equipment. Failure was caused by increasing the inside pressure while keeping the outside pressure constant. At failure, o, = 193 kN/m² and o; = 264 kN/m². The inside and outside radii of the specimen were 40 and 60 mm, respectively. (a) Calculate the soil friction angle. (b) Calculate the axial stress on the specimen at failure.arrow_forward= A standard penetration test is carried out in sand where the efficiency of the hammer n 50%. If the measured N-value at 7.5 m depth is 20, find Noo and (N₁)60. The unit weight of the sand is = 15 MR = 1 and 18.08 kN/m³. Assume ¹ = 0.95. If you know that: nsarrow_forwardDetermine the relative density at each depth using attached equation. Assume moderately compressible sand and hence Qc = 1.arrow_forward
- Determine the relative density at each depth using attached equation. Assume moderately compressible sand and hence Qc = 1.arrow_forwardA dilatometer test (DMT) was conducted in a clay deposit. The water table was located at a depth of 3 mbelow theground surface. At 8 m depth the contact pressure (p1) was 280 kPa and the expansion stress (p2) was 350 kPa.Assume σo = 95 kPa at the 8 m depth and μ = 0.35. Determine (a) Coefficient of at-rest earth pressure Ko,(b) Overconsolidation ratio OCR and (c) Modulus of elasticity Es.arrow_forwardSoilarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781305081550
Author:Braja M. Das
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning