Bundle: Automotive Technology: A Systems Approach, 6th + Online ASE Technician Test Preparation -Automotive Bi-Lingual Series (A6 - Electricity & ... Preparation -Automotive Bi-Lingual Series (A1
6th Edition
ISBN: 9781337217767
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 31, Problem 8RQ
Which of the following would not cause a hard-to-start problem on a PFI engine?
a. A defective IAC valve
b. A defective oxygen sensor
c. A leaking fuel pressure regulator
d. Dirty injectors
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
While discussing GDI systems: Technician A says that this type of system allows engines to run at very lean air-fuel ratios and at higher-than-normal compression ratios. Technician B says that GDI systems eliminate the need to have an EGR valve on the engine. Who is correct?
an engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?
Technician A says that only offshore engines are permitted to use port-helix metering fuel systems on
EPA MY 2010 compliant and later engines. Technician B says that port-helix metering injection
pumps can be used on current diesel engines when the peak power rating is less than 70 BHP (52 kW).
Who is correct?
Chapter 31 Solutions
Bundle: Automotive Technology: A Systems Approach, 6th + Online ASE Technician Test Preparation -Automotive Bi-Lingual Series (A6 - Electricity & ... Preparation -Automotive Bi-Lingual Series (A1
Ch. 31 - List four service precautions for working on the...Ch. 31 - What is indicated by a LTFT reading of 24 percent?Ch. 31 - What is the correct procedure for checking an...Ch. 31 - What is the difference between STFT and LTFT?Ch. 31 - The PCM checks for a closed throttle plate each...Ch. 31 - Which of the following is a likely cause of a lean...Ch. 31 - What problem may result from dirt buildup on an...Ch. 31 - Which of the following would not cause a...Ch. 31 - What is the correct way to test an injector with...Ch. 31 - What is the difference between the pulse width and...
Ch. 31 - How can you use a dual trace scope to make sure...Ch. 31 - What are three possible problems that can allow...Ch. 31 - What is the purpose of having two accelerator...Ch. 31 - What is indicated by a negative LTFT value?Ch. 31 - True or False? The signals from an air-fuel ratio...Ch. 31 - While discussing the causes of...Ch. 31 - While discussing IAC valve diagnosis: Technician A...Ch. 31 - While discussing IAC motor removal, service, and...Ch. 31 - While discussing injector testing: Technician A...Ch. 31 - While discussing airflow sensors: Technician A...Ch. 31 - While discussing scan tool diagnosis of fuel...Ch. 31 - While discussing a high idle speed problem:...Ch. 31 - While discussing the causes of a rich air-fuel...Ch. 31 - While diagnosing an idle speed problem: Technician...Ch. 31 - While looking at fuel trim values: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says there is less heat energy in high octane gasoline and, therefore less power is genorated during combustion. Technician B says usung a higher octane gasoline than required will not produce more power inless the engine has a knock sensor that allows the system to adjust ignition timing to take advantage of the higher octane. who is correct?arrow_forwardWhen the engine is idling, the pressure regulator in a PFI system provides ____fuel pressure compared to the fuel pressure at wide-open throttle.arrow_forwardWhile discussing EFI systems: Technician A says that the PCM provides the proper air-fuel ratio by controlling the fuel pressure. Technician B says that the PCM provides the proper air-fuel ratio by controlling injector pulse width. Who is correct? * 1 point a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Differentiate the two types of external combustion enginearrow_forwardTechnician A says that air-fuel ratios can be regulated by controlling the “on time” of the injectors. Technician B says that the air-fuel ratio can be regulated by controlling the pressure applied to the individual injectors. Who is correct?arrow_forwardWhat are three possible problems that can allow fuel pressure to rapidly bleed down once the engine is shut off?arrow_forward
- What is meant by sequential firing of fuel injectors?arrow_forwardCarbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardWhich of the following is similar to a PCV valve but is specific to diesel engines? PCM EGR AIR CDRarrow_forward
- While discussing the compression ratios used with engines equipped with a GDI system: Technician A says that higher ratios can be used because ignition timing is normally very advanced. Technician B says that higher ratios are possible because the small droplets of fuel injected directly into the cylinder tend to cool the mixture in the cylinder. Who is correct?a.tech a b.tech b c. Both a and b d. Neither a nor barrow_forwardWhen the engine is Idling, the pressure regulator in PFI system provides _____________ fuel pressure compared to the fuel pressure at wild open throttle.arrow_forwardTechnician A says that air-fuel ratios can be regulated by controlling the “on time” of the injectors. Technician B says that the air-fuel ratio can be regulated by controlling the pressure applied to the individual injectors. Who is correct? * 1 point a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY