Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 35, Problem 41RQ
Why might a stress relief heat treatment be performed prior to machining?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What happens to a quench hardened tool or machine part that was not tempered when it is subject to shock loads or bending stress?
1. A milling operation is to be performed on a ductile cast iron shaft to make slots for assembly. The operation will be done at high speeds for good surface finish. For each of the following tool materials, indicate whether it is a reasonable candidate to use in the operation with a detailed description of why or why not including required alloying element/grade/group etc. where applicable:
(i) plain carbon steel,
(ii) high-speed steel,
(iii) cemented carbide,
(iv) ceramic, and
(v) Sintered polycrystalline diamond.
After selection of material/materials discuss about
(i) recommended angles and tool signature
(ii) how to held cutting edge, and type of cutting fluids
With reasons for each recommended material.
2. Make a figure and explain how shear plane angle effect the power requirements in the machining. How can you reduce the power requirements during machining in orthogonal cutting?
1. How does the type of steel used in firearms affect the overall length of its service life?
2. How have the manufacturing processes of the modern Era anabked gunmakers to produce high-quality firearms that will serve the test of time?
3. What are some finishing techniques that may be used to enhance performance as well?
Chapter 35 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 35 - What types of design features favor manufacture as...Ch. 35 - What types of manufacturing processes fall under...Ch. 35 - Define welding.Ch. 35 - What conditions are required to produce an ideal...Ch. 35 - What are some of the ways in which welding...Ch. 35 - What are some possible problems associated with...Ch. 35 - What are the three primary aspects required to...Ch. 35 - How are welding processes identified by the...Ch. 35 - What is thermal cutting?Ch. 35 - What are some of the common types of weld defects?
Ch. 35 - What are the four basic types of fusion welds?Ch. 35 - What are some of the common edge configurations...Ch. 35 - What is the role of an insert in welding?Ch. 35 - What types of weld joints commonly employ fillet...Ch. 35 - What are the five basic joint tvpes for fusion...Ch. 35 - What are some of the factors that influence the...Ch. 35 - Why is it important to consider welded products as...Ch. 35 - How does the fracture resistance and temperature...Ch. 35 - How might excessive rigidity actually be a...Ch. 35 - What is autogenous welding?Ch. 35 - In what way is the weld-pool segment of a fusion...Ch. 35 - Why is it possible for the fusion zone to have a...Ch. 35 - Why is it not uncommon for the selected filler...Ch. 35 - What are some of the defects or problems that can...Ch. 35 - Why can the material properties vary widely within...Ch. 35 - What are some of the structure and property...Ch. 35 - Why do most welding failures occur in the...Ch. 35 - Discuss the various regions within the...Ch. 35 - What are some of the characteristics and...Ch. 35 - What process features can increase the size of the...Ch. 35 - What are some of the difficulties or limitations...Ch. 35 - What is the purpose of pre- and postheating in...Ch. 35 - What heat-related metallurgical effects can...Ch. 35 - What causes weld-induced residual stresses?Ch. 35 - What is the cause of reaction-type residual...Ch. 35 - How are reaction stresses affected by the distance...Ch. 35 - What are some of the techniques that can reduce...Ch. 35 - How can the surfaces of weldments be put into...Ch. 35 - In what ways might welding create geometric...Ch. 35 - 40. Why might a welded structure warp if the...Ch. 35 - Why might a stress relief heat treatment be...Ch. 35 - What are some of the techniques that can be...Ch. 35 - Why are the terms weldability and joinability...Ch. 35 - Prob. 1PCh. 35 - Two pieces of AISI 1025 steel are being...Ch. 35 - Figure 35.A schematically depicts the design of a...Ch. 35 - Investigate and summarize some of the important...Ch. 35 - What do you foresee as the major difficulties when...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
It is necessary to cool and dehumidify air from 80 F db and 67 F wb to 60 F db and 34 F wb. (a) Discuss the fea...
Heating Ventilating and Air Conditioning: Analysis and Design
The friction force at the surface of contact (F).
Engineering Mechanics: Statics & Dynamics (14th Edition)
Determine the largest angle that will cause the wedge to be self-locking regardless of the magnitude of horizo...
Engineering Mechanics: Statics
In each case, determine the internal bending moment as a function of x, and state the necessary boundary and/or...
Mechanics of Materials
Show that this ducted propeller system when moving forward at velocity V1 will have an efficiency given by 2V1/...
Fox and McDonald's Introduction to Fluid Mechanics
Comprehension Check 7-16
A basketball has a diameter of approximately 27 centimeters [cm]. Find the spherical v...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What are the different types of throwaway FGD processes?arrow_forward(a) If you were designing a metallic tool to be used at very low temperatures (negative temperatures), which material class would be the best option?(b) If you wanted to increase the strength of that tool for that very low temperature, which strengthening method would be the best option?arrow_forwardWhat is hot work?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY