![AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS](https://www.bartleby.com/isbn_cover_images/9780135257418/9780135257418_largeCoverImage.gif)
AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
6th Edition
ISBN: 9780135257418
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 4, Problem 3CQ
The three Cs include _____, _____, and _____.
a. correction, correct torque, and customer name
b. concern, cause, and correction
c. cause, cost, and caller name
d. captured data, cause, and cost (of the repair)
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
The term "maintenance" refers to
maintaining all of the systems and
features in working order. *
as close as possible to the original
O design purpose of the manufacturer
tons
as close to the manufacturer's original
design purpose as impossible
as impossible to the manufacturers
original design intent tons.
as possible to the manufacturers
unoriginal design intent tons
skip
Punctures are-
a small hole in a tire resulting in an get-
away of air
a large hole in a tire resulting in an get-
away of air
a small hole in an engine resulting in an
escape of air
a small hole in a tire resulting in an get-
away of oil
Skip
Although the information from different publishers vary in presentation and the arrangement of _______________, all are easy to use after you become familiar with their organization. Most are divided into a number of _______________, each covering different aspects of the _______________. The beginning sections commonly provide vehicle identification and basic maintenance information. The remaining sections deal with each different vehicle _______________ in detail, including diagnostic, _______________, and overhaul procedures. Each section has an index indicating more specific areas of information. To obtain the correct system _______________ and other information, you must first identify the exact system you are working on. The best source for vehicle identification is the _______________. The available information may also help you identify the system through the identification of key _______________ or other identification numbers and/or markings.
(General Questions Not Directly Print Related)
1. ____________use conventional symbols with single lines to show piping and electrical wires. The parts and components are shown by symbols.
A. Diagram Assembly Drawings
B. Altered Item Drawings
C. Modified Item Drawing
D. Dimensioned drawing
2. Balloons are shown on assembly drawings to reference parts to the ___________.
A. Title Block
B. Revision Block
C. Parts List
D. Supplemental B
3.
____________use conventional symbols with single lines to show piping and electrical wires. The parts and components are shown by symbols.
A. Diagram Assembly Drawings
B. Altered Item Drawings
C. Modified Item Drawing
D. Dimensioned drawing
Chapter 4 Solutions
AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
Ch. 4 - What factors are part of being a professional...Ch. 4 - Prob. 2RQCh. 4 - A formal evaluation could include what items?Ch. 4 - What are the three Cs?Ch. 4 - What should be included on the work order after...Ch. 4 - Professionalism includes which factor? a. Keeping...Ch. 4 - Types of communications include _____. a. verbal...Ch. 4 - The three Cs include _____, _____, and _____. a....Ch. 4 - Technician A says that customer-pay rate is...Ch. 4 - Housekeeping duties of a technician can include...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- attached file please. Thank youarrow_forwardWhich statement is true in the case of the term "Precision". The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in condition of measurement. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in time of measurement. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in location. The closeness of output readings when the same input is applied repetitively over a short period of time and there is no change in observer.arrow_forwardA. 18. Surface roughness comparators are used within industry to measure or verify the as manufactured surface finish of a part or assembly. Comparators are selected and used based on the design process used to create a particular A. Tr B. False mess Nonearrow_forward
- Do not give copied/wrong solution.arrow_forwardWhich of the following is least likely to be found on a basic parts list? A. Find Number B. Quantity Required C. Part Nomenclature D. Finish NOTE: I asked this question twice on 2 different occasions and received conflicting answers. First time the answer given to me from this site was "A. FInd Number" and the second time the answer given to me was "D. Finish". I need help figuring out which answer is correct.arrow_forwardDon't provide copied/wrong answerarrow_forward
- Subjects Vibrationarrow_forwarddescribe the information that should be include on a repair order.arrow_forwardComplete the following statement about scan tool using the following words.Words: Activate, Actuators, Always, Computer, Correct, Diagnose, Diagnosing, DTC’s, Procedures, Scan, Management, System A __________ tool and/or a special electronic tester is used to __________ most engine __________system. These can only retrieve __________; they may also be able to __________ various__________ in the system. The exact __________ and available data from the vehicle’s __________will vary with manufacturer and the __________ found on the vehicle. __________ refer to the__________ service information when __________ engine management systems.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337794213/9781337794213_smallCoverImage.jpg)
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license