Introduction to Heat Transfer 6th Edition (Wiley Editor's Choice Edition)
Introduction to Heat Transfer 6th Edition (Wiley Editor's Choice Edition)
6th Edition
ISBN: 9781119936268
Author: Bergman
Publisher: JOHN WILEY+SONS INC.
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 4, Problem 4.1P

In the method of separation of variables (Section 4.2)for two-dimensional, steady-state conduction, the separationconstant λ 2 in Equations 4.6 and 4.7 must be apositive constant. Show that a negative or zero value of λ 2 will result in solutions that cannot satisfy the prescribedboundary conditions.

Expert Solution & Answer
Check Mark
To determine

Whether a negative or zero value of λ2 will result in solutions that cannot satisfy the prescribed boundary conditions.

Answer to Problem 4.1P

The boundary condition 4 results in a trivial solution so a negative or zero value of λ2 will result in solutions that cannot satisfy the prescribed boundary conditions.

Explanation of Solution

Formula Used:

The temperature distribution equation is given by,

  θ(x,y)=X(x)Y(x)  .......(I)

The two dimensional steady state conduction equations is given by,

  2θx2+2θy2=0  .......(II)

Calculation:

Substitute Equation (I) in Equation (II).

  2θx2+2θy2=02( XY)x2+2( XY)y2=0Y2Xx2=X2Yy2  .......(III)

Divide Equation (III) by XY .

  YXY2Xx2=XXY2Yy21X2Xx2=1Y2Yy2  .......(IV)

Use separation constant λ2 in Equation (IV).

  1X2Xx2=λ22Xx2+Xλ2=0  .......(V)

  1Y2Yy2=λ22Yy2Yλ2=0  .......(VI)

Case 1:

Assume λ2=k2 .

Substitute λ2=k2 in Equation (V).

  2Xx2Xk2=0

From the above equation, the auxiliary equation is written as,

  m2k2=0m=±k

Here, the roots for the auxiliary equation are unequal and real.

The general solution for the auxiliary equation is given by,

  X(x)=C1ekx+C2ekx  .......(VII)

Substitute λ2=k2 in Equation (VI).

  2Xx2+Yk2=0

From the above equation, the auxiliary equation is written as,

  m2+k2=0m=±ik

The general solution for the auxiliary equation is given by,

  Y(y)C3cosky+C4sinky  .......(VIII)

Substitute (C1ekx+C2ekx) for X(x) and (C3cosky+C4sinky) for Y(y) in Equation (I).

  θ(x,y)=(C1ekx+C2ekx)(C3cosky+C4sinky)  .......(IX)

Apply boundary condition 1: at y=0 , θ(x,0)=0 in Equation (IX).

  θ(x,0)=(C1e kx+C2e kx)[C3cos(k×0)+C4sin(k×0)]0=(C1e kx+C2e kx)(C3)C3=0

Apply boundary condition 2: at x=0 , θ(0,y)=0 in Equation (IX).

  θ(x,y)=(C1e kx+C2e kx)(C3cosky+C4sinky)θ(0,y)=(C1e k×0+C2e k×0)(C3cosky+C4sinky)0=(C1+C2)(0×cosky+C4sinky)C4=0

A trivial solutions results as the constant C4=0 .

Case 2:

Assume λ2=0 .

Substitute 0 for λ2 in Equation (V).

  2Yy2Y(0)=02Yy2=0

Integrate the above obtained equation.

  dYdy=C7

Integrate the above equation.

  Y(y)=C7y+C8  .......(X)

Substitute (C5x+C6) for X(x) and (C7y+C8) for Y(y) in Equation (I).

  θ(x,y)=(C5xC6)(C7y+C8)  .......(XI)

Apply boundary condition 2: at x=0 , θ(0,y)=0 in Equation (XI).

  θ(x,y)=(C5x+C6)(C7y+C8)θ(0,y)=[C5×(0)+C6](C7y+C8)0=(C6)(C7y+C8)C6=0

Apply boundary condition 1: at y=0 , θ(x,0)=0 in Equation (XI).

  θ(x,y)=(C5x+C6)(C7y+C8)θ(x,0)=(C5x+0)[C7(0)+C8]0=(C5x)(C8)C8=0

Apply boundary condition 3: at x=L , θ(L,0)=0 in Equation (XI).

  θ(x,y)=(C5x+C6)(C7y+C8)θ(L,y)=[( C 5×L)+0](C7y+0)0=(C5L)(C7y)C5=0

Apply boundary condition 4: at y=W , θ(x,W)=1 in Equation (XI).

  θ(x,y)=(C5x+C6)(C7y+C8)θ(x,W)=[(0×x)+0][( C 7×W)+0]1=C7×W10

Conclusion:

The boundary condition 4 results in a trivial solution so a negative or zero value of λ2 will result in solutions that cannot satisfy the prescribed boundary conditions.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A heat-conducting rod, that is wrapped in insulation, is constructed with a 0.15-m length of alloy A and a 0.40-m length of alloy B, joined end-to-end. Both pieces have a cross-sectional area of 0.0020 m2. The thermal conductivity of alloy B is known to be 1.8 times as great as that of alloy A. The end of the rod in alloy A is maintained at a temperature of 10 degrees Celcius, and the other end of the rod is maintained at an unknown temperature. When the steady-state flow has been established, the temperature at the junction of the alloys is measured to be 40 degrees Celcius, and the rate of heat flow in the rod is measured at 56 W. What is the temperature of the end of the rod in alloy B.
Consider two-dimensional steady state conduction in the plate shown. Three sides are maintained at zero temperature. Along the fourth side the temperature varies spatially. Determine the temperature distribution T(x,y) in the plate
If the surface of a plane wall with heat conduction coefficient k is under constant heat flux (q0 ") condition at x = 0 and its surface at x = L is at temperature Ts, which of the following is the temperature distribution of this plane wall?

Chapter 4 Solutions

Introduction to Heat Transfer 6th Edition (Wiley Editor's Choice Edition)

Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
Recommended textbooks for you
Text book image
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license