Concept explainers
The shredder energy requirement for shredding.
Answer to Problem 4.4P
The shredder energy requirement for shredding is
Explanation of Solution
Given:
The fraction of feed retained on sieve is shown in the table below:
Sieve Size |
Fraction of Feed Retained on the Sieve |
Assume, from the figure that the axis is a logarithmic scale then for
Calculation:
Write the equation to calculate the shredder energy requirement for shredding.
Here, the shredder energy is
Write the equation to calculate the slope
Substitute
Write the equation to calculate the slope
Substitute
The slope
Calculate the shredder energy requirement for shredding.
Substitute
Conclusion:
Thus, the shredder energy requirement for shredding is
Want to see more full solutions like this?
- application of fractional losses in pipesarrow_forwardName of a report STRENGTH OF MATERIALS LABORATORY COMPRESSION TEST Hi sir, I know your precious time will be taken, please get a report. I want you to explain to me one or two pages is enough for me, dear sir, by solving the last schedule, may God help you and grant you God bless youarrow_forward(B) Prove the following relations: e-wGs 1) S= 1+e Gs+s.e 2) Yt=¯ Yw 1+e A SaturatodiSam Q2arrow_forward
- A 1.2-ff3 block of aluminum is tied to a piece of cork (SG=0.22), as shown. What volume of cork is required to keep the aluminum (SG=2.7) from sinking in castor oil (SG=0.96)?arrow_forwardFor material testing,Take one destructive and one non-destructive test and explain how both test procedures produce useful results.arrow_forwardThe loads which include the weight of the structural material and the stored products are called : a. ash loads b. dead loads c. live loads d. wind loadsarrow_forward
- Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?arrow_forwardA lead cylinder is placed into a blind hole cut into a large tungstenblock, Assume it is a tight fit. 50 MPa pressure is applied to the top of the cylinder.The cylinder is 100 mm long, and 25 mm in diameter. c)How much shorter will the cylinder get under load? d)What is the volume change? e)Supposethere was a “new lead alloy”where the supplierclaimed it had a Poisson’sratio of0.75. Explain why this claimdefies logic.arrow_forward(c) Elaborate the principles of vacuum forming process for thermoplastics, given a shaped form. Question 5 [4] (a) i. Explain the Spin welding process with the help of a diagram. [6] ii. Name the two requirements for the process to be successful? [4] i. Which are the most common fastners used in assembly? [2] ii. Which joining process could be suitable for joining rubber sheet material? [2] (0) i. Give three reasons why mechanical fastners must be kept to a minimum for the assembly process. [37 What are the three things recommended to lower the assembly costs? [3]arrow_forward
- Mention correct options and provide complete solutionarrow_forwardStandard Test Method for Ductility of Bituminous Materials 1. Importance of ductility test for road construction.2. Iraqi standard for minimum ductility.3. Effect of “temperature and rate of pulling” on ductility value.arrow_forwardA trapezoidal gutter is to be made from a tin by bending up the edges. If the tin has a width of 12 inches and to be folded into three equal parts, find the width across the top gives the maximum carrying capacity. Show detailed solution. (Draw the illustration of the given problem)arrow_forward
- Solid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning