The Science and Engineering of Materials (MindTap Course List)
7th Edition
ISBN: 9781305076761
Author: Donald R. Askeland, Wendelin J. Wright
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 4, Problem 4.51P
(a)
To determine
The Hall-Petch equation’s constants.
(b)
To determine
The required grain size for a strength of 200MPa.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The magnesium-lead alloy was cooled from 600°C to 450°C. Microstructures are composed of initial Mg2Pb and process microstructures factors. Find the composition of this alloy if the weight fraction of the microorganism factor is 0.28.
A 609 g eutectoid steel ( about 0.8%C) is heated to 1,002 C and cooled slowly through the eutectorid temperature. This results in the formation of cementite Fe3C (6.67%C) and ferrite (0.025%C). Calculate the number of grams of cementite that form in the steel.
A 50%Ni-50%Cu alloy is slowly cooled from 1400°C to 1200°C. Determine: At 1300°C, estimate the weight fractions of the solid and liquid.
Chapter 4 Solutions
The Science and Engineering of Materials (MindTap Course List)
Ch. 4 - Gold has 5.82108vacancies/cm3 at equilibrium at...Ch. 4 - Prob. 4.2PCh. 4 - Calculate the number of vacancies per cm3 expected...Ch. 4 - Prob. 4.4PCh. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Prob. 4.7PCh. 4 - Prob. 4.8PCh. 4 - Prob. 4.9PCh. 4 - Au and Ag form a substitutional solid solution....
Ch. 4 - Prob. 4.11PCh. 4 - Prob. 4.12PCh. 4 - Prob. 4.13PCh. 4 - Prob. 4.14PCh. 4 - Prob. 4.15PCh. 4 - Prob. 4.16PCh. 4 - Prob. 4.17PCh. 4 - Prob. 4.18PCh. 4 - Write down the defect chemistry equation for...Ch. 4 - Prob. 4.20PCh. 4 - What is the Burger’s vector orientation...Ch. 4 - What is slip system and what role does it play in...Ch. 4 - Draw a Burgers circuit around the dislocation...Ch. 4 - What are the Miller indices of the slip...Ch. 4 - Prob. 4.25PCh. 4 - Prob. 4.26PCh. 4 - Calculate the length of the Burgers vector in the...Ch. 4 - Prob. 4.28PCh. 4 - Prob. 4.29PCh. 4 - The crystal shown in Figure 4-19 contains two...Ch. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - Prob. 4.33PCh. 4 - Prob. 4.34PCh. 4 - Prob. 4.35PCh. 4 - Prob. 4.36PCh. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Prob. 4.42PCh. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Why is it that single crystal and polycryst alline...Ch. 4 - Prob. 4.46PCh. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Prob. 4.50PCh. 4 - Prob. 4.51PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Prob. 4.57PCh. 4 - Prob. 4.58PCh. 4 - Determine the ASTM grain size number for the...Ch. 4 - Certain ceramics with special dielectric...Ch. 4 - Prob. 4.61PCh. 4 - Calculate the angle of a smalla ngle grain...Ch. 4 - For BCC iron, calculate the average distance...Ch. 4 - Every time we alloy a metal, it gets stronger. Is...Ch. 4 - Prob. 4.65PCh. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Prob. 4.70PCh. 4 - Prob. 4.71PCh. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75DPCh. 4 - You would like a metal plate with good...Ch. 4 - Prob. 4.77DPCh. 4 - Temperature dependence of vacancy conc enlralwns....Ch. 4 - Prob. 4.79CPCh. 4 - Prob. 4.80CPCh. 4 - Describe the problems associated with metal...Ch. 4 - Prob. 4.2KP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An uncold-worked brass specimen of average grain size 0.006 mm has a yield strength of 178 MPa. Estimate the yield strength of this alloy (in MPa) after it has been heated to 600°C for 1000 s, if it is known that the value of ky is 11 MPa-mm1/2. The Animated Figure 7.25 may be helpful. Attached is the question and the figure referenced.arrow_forwardFor the alloy Mg-45 wt% alloy at 500 C, what is the weight percentage of Pb in the alpha phase?arrow_forwardThe yield strength for an alloy that has an average grain diameter of 4.1 × 10-2 mm is 131 MPa. At a grain diameter of 7.6 × 10-3 mm, the yield strength increases to 246 MPa. At what grain diameter, in mm, will the yield strength be 236 MPa?arrow_forward
- Calculate the dislocation spacing of a low-angle tilt boundary in aluminumfor θ = 0.5◦. Take G = 26.1 GPa, v = 0.345, and rAl = 0.143 nm.arrow_forwardExplain the phases shown in the attached image of a stress strain cureve for 0.15% carbon steelarrow_forwardIron (Fe) undergoes an allotropic transformation at 912°C: upon heating from a BCC (α phase) to an FCC (γ phase). Accompanying this transformation is a change in the atomic radius of Fe—from RBCC = 0.12584 nm to RFCC = 0.12894 nm—and, in addition, a change in density (and volume). Compute the percentage volume change associated with this reaction. Indicate a decreasing volume by a negative number.arrow_forward
- Consider an aluminum polycrystal with a grain size of 10 μm. If a dislocationsource at the center of a grain emits dislocations under an appliedshear stress of 50 MPa that pile up at the grain boundaries, what is the stressexperienced by a grain boundary? Take G = 26 GPa and b = 0.3 nm.arrow_forwardCan you explain the kinetics of recovery, recrystallization, and grain growth? (Draw three plots showing the kinetics of each prosess and explain the plot)arrow_forwardPlease show how the value of b was calculated Calculate the dislocation density in tungsten if the stress is controlled by the stress necessary to operate a Frank-Read source. The stress in the plane is 31 Mpa. Take G = 275 Gpaarrow_forward
- Do you have an answer to Q3? "Determine values for the constants n and k for the recrystallization of copper at 119°C. Enter your results in the questions below" jarrow_forwardThe minimum yield strength for iron with an average grain size of 6x10^-2 mm is 135 MPa, this increases to 260 MPa when the average grain size is reduced to 8x10^-3 mm.What must the average grain size be to achieve a yield strength of 205 MPa.arrow_forward1) Give a brief explanation why the solubility of C is higher in y-iron than in alpha-iron. 2) Why must the samples be quenched rapidly to obtain high hardness?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY